Bobcat 310, 313 Skid Steer Loader Service Manual
188 pages · Publication 6556606_12_82
Added to your cart. View cart
What's inside
From the manual's own table of contents: 19 sections, 256 entries. See sample pages (PDF, 253 KB)
INTRODUCTION55 topics
- Symbols
- Serial Number Identifications
- Loader Serial Number
- Engine Serial Number
- Pre-Delivery Inspection
- Hour Inspection
- SERVICE SCHEDULE
- ENGINE SERVICE
- Oil Specifications
- To Check Oil, Add Or Replace
- Engine Oil Filter (313)
- Crankcase Breather
- Air Cooling System (310)
- Engine Cooling Syste (313)
- Spark Arrestor Muffler
- Cleaning The Cooling System (313)
- AIR CLEANER SYSTEM
- FUEL SYSTEM
- Fuel System Service
- Fuel Filter (310)
- Fuel Filter (313)
- Electric Fuel Pump
- ELECTRICAL SYSTEMS
- Fan And Alternator Belt Tension (313)
- Ignition System And Ignition Testing (310)
- Cleaning Or Replacing Spark Plugs
- Ignition Points And Condenser
- Ignition Timing
- Using And Extra Battery
- To Install A New Battery
- HYDRAULIC SYSTEM (313)
- Checking Hydraulic Fluid Level
- To Replace Hydraulic Fluid
- To Replace Hydraulic Filter
- HYDRAULIC SYSTEM (310)
- Checking Hydraulic Fluid Level
- To Replace The Hydraulic Fluid
- Remove Hydraulic Fluid Condensation
- To Replace The Hydraulic Filter
- DRIVE SYSTEM
- Adjustment Of Driven Belts
- Chaincase Hydraulic Fluid
- HYDRAULIC CYLINDERS AND CONTROL VALVE
- Inspecting Hydraulic Cylinders
- To Check Hydraulic Cylinder Seals
- Control Valve
- Adjustment Of Pedal Linkage
- TRANSMISSION AND DRIVE SYSTEM
- Clutches
- Drive Chains
- Tire Inflation
- Tire Rotation
- Tire Replacement
- LUBRICATION
- OPERATOR ENCLOSURE
HYDRAULIC / HYDROSTATIC SCHEMATICS21 topics
- DESCRIPTION OF HYDRAULIC CIRCUIT
- Tubelines, Hoses Fittings
- 37° Flare Connections
- Staright Thread O-ring Fitting
- Pipe Thread Fittings
- Tubelines & Hoses
- Hydraulic Reservoir
- To Check The Hydraulic System
- CHECKING OUTPUT OF HYDRAULIC PUMP
- HYDRAULIC PUMP REPAIR
- CONTROL VALVE
- Removal Of Control Valve
- Disassembly And Inspection Of Control Valve
- Assembling Control Valve
- Detent Spool Repair (Lift And Auxiliary)
- Relief Valve
- To Check Release Pressure
- Removal And Replacement Of Relief Valve
- HYDRAULIC CYLINDER INSPECTION
- TO CHECK CYLINDER SEALS
- REPAIR OF CYLINDER
DESCRIPTION OF DRIVE27 topics
- Clutch Adjustment
- Removal Of Clutch
- Replacement Of Clutch Needle Bearings
- Installation Of Clutch
- DRIVE CHAIN
- Adjustment Of Drive Chain
- Removal Of Drive Chain
- Installation Of Drive Chain
- STEERING LINKAGE
- CHAINCASE & COVER
- LOWER JACKSHAFT
- UPPER JACKSHAFT
- Removal Of Upper Jackshaft
- Disassembly Of Upper Jackshaft
- Installation Of Upper Jackshaft
- Removal Of Upper Jackshaft (One Piece)
- Installation Of Upper Jackshaft (One Piece)
- AXLES & BEARINGS
- To remove The Axles
- Assembly And Installation Of Axle
- TO SERVICE RANGE CONTROL CLUTCH
- To Remove Range Control Clutch
- Inspection Of Range Control Clutch
- Installation Of Range Control Clutch
- PARK BRAKE
- Removing The Park Brake
- Installing The Park Brake
THE BOB-TACH10 topics
- Removal of Bob-Tach
- Installation Of Bob-Tach
- LIFT ARMS
- Removal Of Lift Arms
- Installation Of Lift Arms
- REAR DOOR
- FUEL TANK
- Removal Of Fuel Tank
- Assembly Of Fuel Tank
- LIFT ARM SUPPORT BRACKET
ELECTRICAL SCHEMATICS28 topics
- ELECTRICAL SYSTEM OF THE LOADER
- TROUBLESHOOTING THE ELECTRICAL SYSTEM
- CHARGE SYSTEM SERVICE (310)
- CHARGE SYSTEM CHECKS (310)
- ALTERNATOR SERVICE (313)
- Checking Alternator Output
- Checking Regulator
- Servicing The Alternator
- Disassembly Of The Alternator
- Checking Rotor
- checking Stator
- Checking Diode Trio
- Checking Rectifier
- Alternator Assembly And Installation
- STARTER SERVICE (310)
- To Check Starter
- Removal Of Starter
- Disassembly Of Starter
- To Clean And Inspect Starter
- Replacement Of Brushes
- Starter Dust Shield
- Assembly Of Starter
- STARTER SERVICE (313)
- Checking The Starter
- Armature
- Field Coils
- Brushes & Brush Holders
- Solenoid Operating Test
TROUBLESHOOTING THE 310 ENGINE44 topics
- CARBURETOR
- FUEL PUMP
- GOVENOR
- AUTOMATIC COMPRESSION RELEASE
- Check And Adjustment The Automatic Compression Release
- ENGINE COMPRESSION
- ENGINE SHOCK SUPPORT
- REPAIR AND REPLACEMENT OF THE ENGINE
- TO OVERHAUL THE ENGINE
- DISASSEMBLY AND INSPECTION OF THE ENGINE
- To Check For Oil Leakage
- Disassembly Of The Engine
- Inspection And Cleaning Of Parts
- Cylinder Block
- Crankshaft
- Connecting Rod
- Piston And Piston Rings
- Piston And Rod
- Valve And Valve Mechanism
- Cylinder Head
- Ring Gear
- Dynamic Balance System
- Timing The Balance Gears
- ASSEMBLY OF THE ENGINE
- Rear Main Bearings
- Installation Of The Govenor
- Installation Of The Camshaft
- Installation Of The Crankshaft
- Installation Of The Bearing Plate
- Assembly Of Piston And Rod
- Assembly Of Connecting Rod To Cranshaft
- Installation Of Oil Seals On Crankshaft
- Installation Of The Oil Pan
- Installation Of The Valves
- Installation Of The Cylinder Head
- Engine Breather
- Installation Of The Flywheel
- Installation Of The Breaker Points
- Installation Of The Carburetor
- Installation Of The Govenor Linkage
- Installation Of The Blower Cover
- TO START A RECONDITIONED ENGINE
- Disassembly Of The Carburetor
- Assembly Of The Carburetor
TROUBLESHOOTING THE 313 ENGINE22 topics
- To Replace The Fuel Filter
- To Vent Vent The Fuel System
- Removal And Installing Fuel Injection Pump
- Timing The Fuel System
- Fule Lift Pump
- LUBRICATION SYSTEM
- RECONDITIONING THE ENGINE
- Removal Of Engine
- Cylinder Head Combustion Chamber
- Valve Adjustment
- Cylinder Head Removal
- Reconditioning The Valves
- Inspection Of The Rocker Arms
- Installation Of Cylinder Head
- To Adjust The Compression Release Mechanism
- Disassembly Of The Engine
- Cylinder Liners
- Crankshaft And Connecting Road Installation
- Camshaft And Camshaft Gear
- Installing Idler Gear And Govenor
- Installing Gearcase Housing
- Install Flywheel To Crankshaft
FUEL SPECIFICATIONS30 topics
- ENGINE OIL SPECIFICATIONS
- HYDRAULIC FLUID
- LOADER SPECIFICATIONS
- Operation & Performance
- Engine
- Hydraulic System
- Electrical
- Drive System
- Tires
- Fluid Capacities
- TORQUE SPECIFICATIONS
- ENGINE SPECIFICATION
- Torques
- Fits & Clearance
- Maximum Wear Tolerance & Clearance
- LOADER SPECIFICATIONS
- Operation & Performance
- Engine
- Hydraulic System
- Electrical
- Drive System
- Capacities
- Tires
- ENGINE SPECIFICATIONS
- Torque
- Fits & Clearance
- SPECIAL TOOLS
- STANDARD TORQUE SPECIFICATIONS FOR BOLTS
- DECIMAL AND MILLIMETER EQUIVALENTS
- U.S. TO METRIC CONVERSION
Inside this manual
Real pages from this service manual (192 pages). Open the sample pages (PDF, 253 KB)
- Color page, page 9
- Color page, page 90
- Foldout diagram (color), page 36
Other manuals for this machine
Save 10% on 2 manuals, 15% on 3 or more. Other manuals are listed below. Editions cover different serial number ranges: check the serial coverage and tick only the ones that match your machine.
Added to your cart. View cart
This is a service manual
Here's how it compares to the other manual types.
Service manual
Factory repair procedures and technical information such as specifications, troubleshooting, and wiring and hydraulic diagrams, for the models and systems the manual covers. See What's inside for its topics.
Operator's manual
Safe operation, controls, maintenance schedules, lubrication points, inspections, and basic checks. Repair procedures are in the service manual.
Parts manual
Illustrated diagrams with factory part numbers for identifying components and ordering parts. Repair procedures are in the service manual.
Engine service manuals are sometimes sold separately, since certain machine models were offered with more than one engine option.
What it's used for
Factory manual for in-house farm and construction shop use. Straightforward, complete, and easy to follow. It contains the OEM information dealership service departments and parts counters use to diagnose problems, identify components, and perform maintenance or repairs correctly.
Service shops and owner/operators who repair their own equipment
Identifying correct parts and seeing how assemblies come apart and go back together
Keeping equipment running with less downtime
Factory manual, 188 pages
Quantity one is the manual described above.
Fast free USA shipping
Ships in 1 business day.
60-day returns
Free if the mistake is ours. A manual ordered in error must come back unopened in its shrink-wrap; you pay return shipping and a 20% restocking fee applies. Return policy
Questions about model, serial number, engine coverage or contents? Contact us before purchasing and we'll help confirm it's the right manual. Please verify the manual type, machine model, serial number range and engine coverage before purchasing: manuals ordered in error carry a 20% restocking fee (return policy).