MidWestTechService, Parts and Operator's Manuals, in stock and ready to ship!
Fast free USA shippingShips in 1 business daySave 10% on 2 manuals, 15% on 3+

Case DCX101 Disc Mower Conditioner Service Manual

260 pages · Publication 87548193

$69.65
Fast free USA shippingShips in 1 business daySave 10% on 2 manuals, 15% on 3 or morePay by credit or debit card or with PayPal. No PayPal account needed.
Models
DCX101
Manual type
Service Manual
Pages
260
Publication
87548193
Condition
Brand new
Case DCX101 Disc Mower Conditioner Service Manual, publication 87548193

What's inside

From the manual's own table of contents: 124 sections, 166 entries. See sample pages (PDF, 452 KB)

Foreword
Precautionary Statements
Safety
Product Identification Number
Manual Holder
Hardware Torque Values
Installation of Adjustable Fittings in Straight Thread O-Ring Bosses
Standard Torque Data For Hydraulic Tubes and Fittings
Pipe Thread Fitting Torque
Installation of ORFS (O-Ring Flat Faced) Fittings
Ecology and the Environment
Universal Symbols
Tractor Requirements
Tractor Drawbar Dimensions
Attaching the Mower-conditioner to the Tractor
Jack Assembly
Hydraulic Hoses
Hydraulic Cylinders
Connecting Hydraulic Hoses to the Tractor
Bleeding Air from the Lift Cylinders
Transporting the Mower-conditioner
Slow-moving Vehicle Emblem
Transporting on Highways
Safety Chain
Show all 124 sections
Trailing Lights
Towing with a Tractor
Towing with a Truck
Parking the Machine
Storing the Mower-conditioner
Specifications
Special Tools
Conditioning (Roll Pressure)
Unplugging The Conditioner Rolls
Roll Timing2 topics
  • Rubber Rolls
  • Steel Rolls
Roll Gap
Conditioner Belt
Cutter Bar Flotation
Cutting Height
Lubrication
Recommended Lubricants
Lubrication Schedule
Grease Fittings
Gearboxes
PTO Slide Collar
Weasler Primary PTO
Every 50 Hours
Bondioli Primary PTO
Secondary PTO3 topics
  • Front CV Joint
  • Telescoping Section
  • Rear CV Joint and Slip Clutch Assembly
Roll Drive
Cutter Bar Drive Shaft
Upper Roll Pivot Arms
Wheel Arms and Header Lift Arms
Tongue Pivot Pin
Wheel Bearings
Cutter Bar Mounting Bolts
After First 50 Hours
Step-up Gearbox
Every 100 Hours
Roll Pressure Crank
Bevel Gearbox
Every 200 Hours
Roll Drive Gearbox
Cutter Bar Modules
Every 400 Hours
Troubleshooting
Description of Operation2 topics
  • Slide Lock -- Disassembly
  • Slide Lock -- Assembly
Drive Shaft Removal/Installation
Primary PTO2 topics
  • RPM PTO Units
  • Secondary PTO Assembly
RPM PTOs5 topics
  • Standard Drivelines Guards -- Disassembly
  • CV Drivelines Guards -- Disassembly
  • Driveline Guards -- Inspection
  • Standard Driveline Guards -- Assembly
  • Front Guard Assembly
RPM PTOs5 topics
  • RPM Assembly
  • Secondary PTO Disassembly
  • U-joints -- Disassembly
  • U-joints -- Inspection
  • U-joints -- Assembly
Repair Time Schedule
Slip Clutch6 topics
  • Slip Clutch - Removal
  • Slip Clutch - Disassembly
  • Slip Clutch - Inspection
  • Slip Clutch - Assembly
  • Slip Clutch - Installation
  • Slip Clutch - Run In
Overrunning Clutch3 topics
  • Overrunning Clutch - Disassembly
  • Overrunning Clutch - Inspection
  • Overrunning Clutch - Assembly
Slip with Overrunning Clutch5 topics
  • Disassembly
  • Assembly
  • To Convert Step-up Gearbox for Different PTO Speed
  • Step-up Gearbox - Disassembly
  • Step-up Gearbox - Assembly
Hydraulic Diagram
Lift Cylinder Removal
Master Cylinder1 topic
  • Inspection
Slave Cylinder
Header Tilt Cylinder1 topic
  • Removal
Swing Cylinder
Adjustment
Removal
Installation
Disassembly: Flotation Spring Wrench
Disassembly
Assembly3 topics
  • Installing the Wire Harness
  • Installing the Lights
  • Installing the Socket
Introduction
Discs
Knife and Bolt Inspection
Knife Replacement
Crop Lifter Replacement
Rock Guard Replacement
Skid Shoe Replacement
Cutter Bar Inspection/Failure Analysis
Top Cap Removal
Top Cap Installation
Cutter Bar Removal
Cutter Bar Installation
Cutter Bar Bayonet Bushing - Replacement
Cutter Bar Disassembly
Cutter Bar Reassembly
Disc Module - Disassembly
Disc Module - Assembly
Cutter Bar Drive Shaft - Disassembly
Cutter Bar Drive Shaft - Assembly
Bevel Gearbox - Removal
Bevel Gearbox - Disassembly
Bevel Gearbox - Reassembly
Bevel Gearbox - Installation
Conditioner Belt Replacement
Conditioner Roll Gearbox - Removal
Conditioner Roll Gearbox - Disassembly
Conditioner Roll Gearbox - Assembly
Conditioner Roll Gearbox - Installation
Upper Conditioner Roll Drive Shaft - Disassembly
U-joints - Assembly
Lower Conditioner Roll - Removal
Lower Conditioner Roll - Installation
Upper Conditioner Roll - Removal
Upper Conditioner Roll - Installation
Conditioner Roll Tension System2 topics
  • Left Side Torsion Arm and Bar Disassembly
  • Right Side Torsion Arm, Torsion Bar and Adjusting Tube Disassembly
Conditioner Roll Tension System - Assembly2 topics
  • Right Side Torsion Arm, Torsion Bar and Adjusting Tube Assembly
  • Left Side Torsion Arm and Bar Assembly
High Stubble Kit
Safety Decals

Inside this manual

Real pages from this service manual (260 pages). Open the sample pages (PDF, 451 KB)

Sample pages from the Case DCX101 Disc Mower Conditioner Service Manual: Specifications, Troubleshooting, Diagram
  • Specifications, page 45: SECTION 00 - GENERAL INFORMATION - CHAPTER 2
  • Troubleshooting, page 65: SECTION 00 - GENERAL INFORMATION - CHAPTER 4
  • Diagram, page 153: SECTION 55 - ELECTRICAL SYSTEM - CHAPTER 1

This is a service manual

Here's how it compares to the other manual types.

This manual

Service manual

Factory repair procedures and technical information such as specifications, troubleshooting, and wiring and hydraulic diagrams, for the models and systems the manual covers. See What's inside for its topics.

Operator's manual

Safe operation, controls, maintenance schedules, lubrication points, inspections, and basic checks. Repair procedures are in the service manual.

Parts manual

Illustrated diagrams with factory part numbers for identifying components and ordering parts. Repair procedures are in the service manual.

Engine service manuals are sometimes sold separately, since certain machine models were offered with more than one engine option.

What it's used for

Factory manual for in-house farm and construction shop use. Straightforward, complete, and easy to follow. It contains the OEM information dealership service departments and parts counters use to diagnose problems, identify components, and perform maintenance or repairs correctly.

Service shops and owner/operators who repair their own equipment

Identifying correct parts and seeing how assemblies come apart and go back together

Keeping equipment running with less downtime

Factory manual, 260 pages

Quantity one is the manual described above.

Fast free USA shipping

Ships in 1 business day.

60-day returns

Free if the mistake is ours. A manual ordered in error must come back unopened in its shrink-wrap; you pay return shipping and a 20% restocking fee applies. Return policy

Other editions and similar models

Questions about model, serial number, engine coverage or contents? Contact us before purchasing and we'll help confirm it's the right manual. Please verify the manual type, machine model, serial number range and engine coverage before purchasing: manuals ordered in error carry a 20% restocking fee (return policy).