Case Early Riser 1235 Mounted Stacker Planter Operator's Manual
292 pages · Publication 47698216
Added to your cart. View cart
- Models
- Early Riser 1235 Mounted Stacker
- Manual type
- Operator's Manual
- Pages
- 292
- Publication
- 47698216
- Condition
- Brand new
What's inside
From the manual's own table of contents: 16 sections, 133 entries. See sample pages (PDF, 534 KB)
Safety signs117 topics
- Tractor requirements
- Tractor hitch
- Hydraulic connections
- Motor case drain kits
- Lift assist wheel connections
- Electrical connections
- Planter preparation
- Forward mounted carrying wheels - 12 Row planters only
- Planting with hydraulic drive planters
- Balancing hydraulic load
- Folding and unfolding the planter
- Planter raising and lowering
- Frame modes
- Row unit operation
- Advanced Seed Meter (ASM) components
- Row unit down pressure adjustment
- AccuRow system (if equipped)
- Covering disk adjustment
- Meter unit speed compensator
- Removing the AccuDrive cable assembly
- Row unit seed hopper removal and installation
- Seed meter field operation
- Singulator and baffle adjustment
- AccuStat seed sensor
- Row unit hopper filling
- Vacuum adjustment
- Variable drive: row unit and seed meter drive
- Variable drive: planting speed
- Mechanical transmission
- Check planting results
- Drive wheel slip adjustment
- Advanced Farming System (AFS®) Pro 700 - Ground drive transmission
- Early Riser® IV monitor - Ground drive transmission
- Marker length adjustment
- Marker disk angle adjustment
- Marker breakaway adjustment
- Marker weight bias spring
- Adjust offset pivots
- No installed markers - Weight kit
- Marker controller operation
- Tillage support mounted attachments
- Granular chemical components
- Drive clutch control
- Granular chemical hopper
- Metering valve operation and adjustment
- Adjusting broadcast coverage rate
- Effects of varying seed rate on chemical rate
- Metering gate calibration
- Spring tooth incorporator
- Recommended settings chart
- Seed population/spacing chart
- Seed disk RPM
- Optimum operating range for planting peanuts
- Mechanical transmission sprocket tables
- Maintenance safety
- Maintenance accessories
- Torque - Hydraulic tubes and fittings – Hydraulic tubes and fittings
- Torque - Fasteners – Fasteners
- Maintenance chart
- Drive chain lubrication
- Mechanical transmission chain lubrication (if equipped)
- Lighting operation
- Pneumatic air compressor filter (if equipped)
- Pneumatic air tanks (if equipped)
- Ratchet clutch, wheel pivot and drive bearing
- Wheel torque
- Lift assist wheels (if equipped)
- Drive chain adjustment
- Marker lubrication (if equipped)
- Telescoping drive shaft
- Mechanical transmission set screws
- Drive wheel chain scraper
- Wheels and tires
- Frame lubrication
- Row unit hopper seed level sensor
- Granular chemical hopper level sensor
- Drive wheel bearings
- Granular chemical hoppers (if equipped)
- Granular chemical meter (if equipped)
- Lift assist wheel bearings
- Hydraulic hoses, cylinder rods and sprockets
- Pneumatic Down Pressure (PDP) compressor filter
- Seed meter inspection
- Singulator spool replacement procedure
- Singulator replacement
- Seed disk replacement
- Meter curved brush replacement
- Straight brush removal/replacement
- Seed tube cleaning
- Seed tube / seed sensor replacement
- Row unit tie strap location
- Opener disk inspection and replacement
- Disk scrapers
- Inspect closing disk
- Furrow firming point
- Replace firming point
- Seed shoe
- Check depth control
- Adjust depth control
- Ground speed sensor
- Vacuum gauge zero adjustment
- Vacuum sensor
- Seed meter vacuum system cleaning
- Hub bearings - Residue/tillage attachments
- Preparing for storage
- Lift assist wheels (if equipped)
- Seed disks and agitators
- Markers (if equipped)
- Mechanical transmission drive chains (if equipped)
- Drive chains
- Granular chemical hoppers (if equipped)
- Pneumatic Down Pressure (PDP) (if equipped)
- Air tank(s)
- General storage practices
- Planter specifications
- Delivery check sheet - Customer copy
- Delivery check sheet - Dealer copy
Inside this manual
Real pages from this operator's manual (292 pages). Open the sample pages (PDF, 534 KB)
- Controls and operation, page 118: Automatic marker switch
- Maintenance, page 194: Telescoping drive shaft
- Specifications, page 278: 7 - SPECIFICATIONS
This is an operator's manual
Here's how it compares to the other manual types.
Service manual
Factory repair procedures and technical information such as specifications, troubleshooting, and wiring and hydraulic diagrams, for the models and systems the manual covers. See What's inside for its topics.
Operator's manual
Safe operation, controls, maintenance schedules, lubrication points, inspections, and basic checks. Repair procedures are in the service manual.
Parts manual
Illustrated diagrams with factory part numbers for identifying components and ordering parts. Repair procedures are in the service manual.
What it's used for
Factory manual for in-house farm and construction shop use. Straightforward, complete, and easy to follow. It contains the OEM information dealership service departments and parts counters use to diagnose problems, identify components, and perform maintenance or repairs correctly.
Service shops and owner/operators who repair their own equipment
Identifying correct parts and seeing how assemblies come apart and go back together
Keeping equipment running with less downtime
Factory manual, 292 pages
Quantity one is the manual described above.
Fast free USA shipping
Ships in 1 business day.
60-day returns
Free if the mistake is ours. A manual ordered in error must come back unopened in its shrink-wrap; you pay return shipping and a 20% restocking fee applies. Return policy
Questions about model, serial number, engine coverage or contents? Contact us before purchasing and we'll help confirm it's the right manual. Please verify the manual type, machine model, serial number range and engine coverage before purchasing: manuals ordered in error carry a 20% restocking fee (return policy).