Case RB565 Round Baler Operator's Manual
358 pages · Publication 90437610
Added to your cart. View cart
- Models
- RB565
- Serial coverage
- PIN HBJRB560AKN198755 and after
- Manual type
- Operator's Manual
- Pages
- 358
- Publication
- 90437610
- Condition
- Brand new
What's inside
From the manual's own table of contents: 22 sections, 190 entries. See sample pages (PDF, 715 KB)
Informational decals139 topics
- Tractor requirements
- Tractor preparation
- Maximum static weight on the towing vehicle
- Tractor attachment
- Operator's panel / Virtual Terminal (VT) display mounts
- Operator's panel overview
- Deluxe operator's panel – Installation on the tractor
- Virtual Terminal (VT) display overview
- Virtual Terminal (VT) – Installation on the tractor
- Power-wire harness
- Electrical connections
- Hydraulic hose connections
- Hydraulic bale ramp connection (if equipped)
- Power Take-Off (PTO) connection
- Baler running-in procedure
- Bale-forming belt break-in
- Baler parking
- Baler towing
- Implement lighting control module
- Flatbed transport
- Lifting the machine
- Safety rules – Machine service access
- Bale formation rollers – Remove debris – Cleaning
- Driveline protection
- Baler controls
- Hydraulic tension system
- Bale density pressure
- Density cylinder system pressure – Mechanical adjust
- Density cylinder system pressure – In-cab (electronic) adjust
- Basic bale formation components
- Starting the bale
- Bale formation
- Bale completion
- Bale ejection
- Pickup lift setup
- Pickup gauge wheels
- Pickup flotation – Flotation springs
- Windguard
- Scraper clearance adjustment
- Baler start-up
- Crop preparation
- Baling
- Baling – Bale core formation
- Baling – Bale feeding – Windrow and driving patterns
- Baling – Bale shape and windrow formation
- Pickup – Remove a blockage of crop material
- Completing the bale
- Bale-forming belt de-clutch (if equipped) – Functional overview
- Bale-forming belt de-clutch (if equipped) – Technical overview
- Baling – Bale ejection – Spring type bale ramp
- Baling – Bale ejection – Hydraulic bale ramp (if equipped)
- TWINE WRAPPER
- Twine wrapper cycle
- Twine arm spacing
- Twine end distance
- Twine knife
- Twine ball joining knots
- Twine tension
- Twine spinner guide orientation
- Twine routing decal
- Twine installation – Twine (only) baler
- Twine installation – Net/Twine baler
- NET WRAPPER
- Net wrapper cycle
- Net roll installation
- Net tension – Check – Net tension pull test
- Net wrapping – Check
- Safety rules – Machine service access
- Welding on the machine – General welding
- Jacking points
- Hardware overview – Hardware specification examples
- Torque specifications – Nominal tightening torque values for normal assembly
- Standard torque data for hydraulics
- Consumables
- Lubrication
- Bale-forming belt tension
- Roller chains
- Laced bale-forming belt – Repair
- Maintenance chart
- Grease points
- Oil locations – Roller drive chains
- Roller bearings – Inspection for failure – Check
- Gearbox oil – Change fluid
- Net brake – Adjust (when the brake pad is new or a new replacement)
- Grease points
- Oil locations
- Gearbox oil level – Check
- Bale-forming belts – Check
- Hardware tightness – Check
- Adjustable tailgate idler roll – Check
- Pickup drive chain – Adjust – 1.5 m Standard pickup
- Wide pickup jackshaft drive chain – Adjust – Over Shot Feeder (OSF)
- Sledge pivot roll drive chain – Adjust
- Bale-forming belt drive roll chain – Adjust
- Floor roll drive chain – Adjust
- Starter roll drive chain – Adjust
- Stationary roll drive chain – Adjust
- Chain stretch – Check
- Scraper clearance – Check
- Tire pressure and wheel hardware torque
- Hydraulic hoses – Check
- Wheel bearings – Grease
- Lubrication points
- Gearbox oil – Change fluid
- Hydraulic hose – Expiration interval – Replace
- Cleaning the machine
- Automatic greaser reservoir – Filling
- Automatic greaser system – Bleed
- Density cylinder system – Charging – Overview, specifications, and requirements
- Bale formation – Operator's panel electronic controls – Adjust
- Tailgate chopping roll – Check (if equipped)
- Dual sledge follower rolls – Check (if equipped)
- Bale-forming belt – Standard lacing cable – Replace
- Bale-forming belt repair – Clipper® hook-type lace – Replace
- Bale-forming belts – Premium lacing pin – Replace
- Bale-forming belt repair – MATO rivet-type lace – Replace
- Endless bale-forming belt – Replace
- Bale-forming belts slipping – Adjust
- Bale-forming belts tracking – Adjust
- Bale-forming belt drive de-clutch (if equipped) – Hex shaft – Adjust
- Bale-forming belt drive de-clutch (if equipped)
- Bale-forming belt drive de-clutch (if equipped) Disengagement angle – Adjust
- Pickup auger scraper clearance – Adjust
- Pickup tine – Replace
- Power Take-Off (PTO) cut-out clutch – Check
- Pickup – 1.5 m Standard pickup – Friction disc slip clutch – Check
- Pickup – 1.5 m Standard pickup – Friction disc slip clutch – Adjust and burnish
- Net wrapper knives – Resurface (Sharpen)
- Twine knife – Resurface (Sharpen)
- Net wrapper duckbill baffle – Check and adjust
- Net wrapper duckbill return spring – Adjust
- Brake lift-off – Adjust
- Net tail length – Adjust
- Net tension – Adjust
- Preparing for storage
- Bale-forming belts – Storing
- End of season – Check and replace parts
- Removing from storage
- Problem / Possible cause / Correction
Specification – Over Shot Feeder (OSF)29 topics
- Specification – Bale-forming belts
- Specification – Bale wrapping mechanisms
- Automatic greaser kit
- Auxiliary twine box kit
- Bale-forming belt de-clutch kit
- Bale ramp sensor kit
- Chain oiler kit
- Dual castering pickup gauge wheels kit
- Dual no-tools adjustable gauge wheels kit
- Dual sledge follower roll kit
- Fire extinguisher kit
- Hydraulic pickup lift kit
- Implement lighting control module – Service part
- ISOBUS automation – Bale presence switch kit
- Lacing cable kit - Heavy duty
- Lacing cable kit - Standard
- Left-hand tailgate latch sensor kit
- Moisture sensor kit
- Operator's panel mounting kit
- Roller windguard kit – 1.5 m (meter)
- Roller windguard kit – 2.0 m (meter)
- Rotor transition kit
- Serpentine scraper kit – 5 ft (foot)
- Suction cup operator's panel mounting kit
- Tailgate chopping roll kit
- Twine motion sensor kit
- Twine straw kit
- Delivery report – Owner's copy
- Delivery report – Dealer's copy
Inside this manual
Real pages from this operator's manual (358 pages). Open the sample pages (PDF, 713 KB)
- Maintenance, page 217: MAINTENANCE CHART
- Controls and operation, page 277: Bale formation – Operator's panel electronic controls – Adjust
- Specifications, page 327: 8 - SPECIFICATIONS
- Color page, page 74: 2 - SAFETY INFORMATION
- Color page, page 48: 2 - SAFETY INFORMATION
This is an operator's manual
Here's how it compares to the other manual types.
Service manual
Factory repair procedures and technical information such as specifications, troubleshooting, and wiring and hydraulic diagrams, for the models and systems the manual covers. See What's inside for its topics.
Operator's manual
Safe operation, controls, maintenance schedules, lubrication points, inspections, and basic checks. Repair procedures are in the service manual.
Parts manual
Illustrated diagrams with factory part numbers for identifying components and ordering parts. Repair procedures are in the service manual.
What it's used for
Factory manual for in-house farm and construction shop use. Straightforward, complete, and easy to follow. It contains the OEM information dealership service departments and parts counters use to diagnose problems, identify components, and perform maintenance or repairs correctly.
Service shops and owner/operators who repair their own equipment
Identifying correct parts and seeing how assemblies come apart and go back together
Keeping equipment running with less downtime
Factory manual, 358 pages
Quantity one is the manual described above.
Fast free USA shipping
Ships in 1 business day.
60-day returns
Free if the mistake is ours. A manual ordered in error must come back unopened in its shrink-wrap; you pay return shipping and a 20% restocking fee applies. Return policy
Binder not included
Manuals over about 300 pages may need a standard 3-ring binder, which you can buy locally to keep the pages organized for shop use.
Questions about model, serial number, engine coverage or contents? Contact us before purchasing and we'll help confirm it's the right manual. Please verify the manual type, machine model, serial number range and engine coverage before purchasing: manuals ordered in error carry a 20% restocking fee (return policy).