Komatsu D155AX-5 Bulldozer Operation & Maintenance Manual
303 pages · Publication EEAM023402
Added to your cart. View cart
- Models
- D155AX-5
- Serial coverage
- D155AX 76243 and up
- Manual type
- Operation & Maintenance Manual
- Pages
- 303
- Publication
- EEAM023402
- Condition
- Brand new
What's inside
From the manual's own table of contents: 76 sections, 203 entries. See sample pages (PDF, 371 KB)
Vibration levels1 topic
- Guide to Reduce Vibration Levels on Machine
Show all 76 sections
GENERAL VIEW2 topics
- GENERAL VIEW OF MACHINE
- GENERAL VIEW OF CONTROLS AND GAUGES
EXPLANATION OF COMPONENTS41 topics
- FRONT PANEL
- CHECK MONITOR GROUP
- CAUTION MONITOR GROUP
- EMERGENCY CAUTION ITEMS
- METER GROUP
- SWITCHES
- LAMPS
- METHOD OF USING DISPLAY PANEL B (Multi-information)
- SWITCHES
- CONTROL LEVERS, PEDALS
- DUST INDICATOR
- POWER SOURCE
- FUSE BOX
- CIRCUIT BREAKER
- CIRCUIT BREAKER FOR MAIN POWER SUPPLY
- FUSE CAPACITY AND NAME OF CIRCUIT
- DOOR POCKET
- ASHTRAY
- CAR RADIO, HANDLING
- EXPLANATION OF COMPONENTS
- METHOD OF USE
- PRECAUTIONS WHEN USING
- CAR STEREO, HANDLING
- EXPLANATION OF COMPONENTS
- METHOD OF OPERATION
- PRECAUTION WHEN USING
- AIR CONDITIONER
- GENERAL LOCATIONS AND FUNCTION OF CONTROL PANEL
- METHOD OF OPERATION
- PRECAUTIONS WHEN USING
- SET SO THAT COLD AIR DOES NOT DIRECTLY BLOW ONTO THE GLASS SURFACE
- CHECKS DURING OFF-SEASON
- PROCEDURE FOR REPLACING RECEIVER
- CHECK COMPRESSOR BELT TENSION AND REFRIGERANT (GAS) LEVEL
- CLEANING AIR FILTER
- SKILLFUL USE OF AIR-CONDITIONER
- HEATER, HANDLING
- METHOD OF OPERATION
- CLEANING AIR FILTER
- ACCUMULATOR, HANDLING
- ACCUMULATOR
CHECK BEFORE STARTING ENGINE, ADJUST4 topics
- CHECK
- CHECK BEFORE STARTING
- ADJUSTMENT
- OPERATIONS AND CHECKS BEFORE STARTING ENGINE
STARTING ENGINE2 topics
- NORMAL STARTING
- STARTING IN COLD WEATHER
OPERATIONS AND CHECKS AFTER STARTING ENGINE2 topics
- WARMING UP OPERATIONS
- IN COLD AREAS
STEERING MACHINE9 topics
- NORMAL TURNING
- TURNING WHILE DESCENDING A SLOPE
- PAY ATTENTION TO GAUGES
- PERMISSIBLE WATER DEPTH
- PRECAUTIONS WHEN TRAVELING UP OR DOWN HILLS
- PRECAUTIONS ON SLOPE
- METHOD OF USING BRAKES
- PROHIBITED TO KEEP THE DOOR OPEN DURING OPERATIONS
- PRECAUTIONS FOR BLIND SPOTS CAUSED BY CAB STAY AND ROPS STAY
RIPPER OPERATION4 topics
- EFFECTIVE METHOD OF USE
- DIGGING UP BOULDERS OR ROCKBED
- OPERATING ON SLOPES
- METHOD OF OPERATING PIN PULLER
OPERATING METHOD FOR RIPPING OPERATIONS5 topics
- BASIC OPERATING METHOD
- RIPPING BY CLIFFS
- RIPPING BY SLOPE FACES
- DIGGING UP BOULDERS
- PRECAUTIONS WHEN RIPPING
WORK POSSIBLE USING BULLDOZER20 topics
- DOZING
- SMOOTHING
- CUTTING INTO HARD OR FROZEN GROUND OR DITCHING
- FELLING TREES, REMOVING STUMPS
- PUSHER OPERATIONS
- ADJUSTING POSTURE OF WORK EQUIPMENT
- METHOD OF ANGLING BLADE
- ADJUSTING TILT AMOUNT
- ADJUSTING RIPPER
- ADJUST ANGLE OF BLADE EDGE
- TIPS FOR LONGER UNDERCARRIAGE LIFE
- OPERATION METHOD
- INSPECTION AND ADJUSTING
- INSPECTION AND REPAIR
- LOADING, UNLOADING WORK
- PRECAUTIONS FOR LOADING
- METHOD OF LIFTING MACHINE
- PRECAUTIONS FOR TRANSPORTATION
- TRAVELING ON ROADS
- REMOVAL OF CAB
COLD WEATHER OPERATION6 topics
- PRECAUTIONS FOR LOW TEMPERATURE
- FUEL AND LUBRICANTS
- COOLANT
- BATTERY
- AFTER COMPLETION OF WORK
- AFTER COLD WEATHER
STORAGE3 topics
- BEFORE STORAGE
- DURING STORAGE
- AFTER STORAGE
TROUBLESHOOTING12 topics
- AFTER RUNNING OUT OF FUEL
- PROCEDURE FOR BLEEDING AIR
- METHOD OF TOWING MACHINE
- IF BATTERY IS DISCHARGED
- REMOVAL AND INSTALLATION OF BATTERY
- PRECAUTIONS WHEN CHARGING BATTERY
- STARTING ENGINE WITH BOOSTER CABLE
- OTHER TROUBLE
- ELECTRICAL SYSTEM
- MONITOR PANEL
- CHASSIS
- ENGINE
HANDLING OIL, FUEL, COOLANT, AND PERFORMING OIL CLINIC6 topics
- FUEL
- COOLANT AND WATER FOR DILUTION
- GREASE
- CARRYING OUT KOWA (Komatsu Oil Wear Analysis)
- STORING OIL AND FUEL
- FILTERS
MAINTENANCE SCHEDULE CHART8 topics
- INITIAL 250 HOURS SERVICE (ONLY AFTER THE FIRST 250 HOURS)
- WHEN REQUIRED
- EVERY 250 HOURS SERVICE
- EVERY 500 HOURS SERVICE
- EVERY 1000 HOURS SERVICE
- EVERY 2000 HOURS SERVICE
- EVERY 4000 HOURS SERVICE
- EVERY 8000 HOURS SERVICE
SPECIFICATIONS1 topic
- PRECAUTIONS RELATED TO SAFETY
CAP WITH LOCK, HANDLING1 topic
- METHOD OF OPENING AND CLOSING CAP WITH LOCK
Inside this manual
Real pages from this operation & maintenance manual (303 pages). Open the sample pages (PDF, 371 KB)
- Controls and operation, page 147: OPERATIONS AND CHECKS BEFORE STARTING ENGINE
- Maintenance, page 231: SERVICE PROCEDURE
- Specifications, page 291: SPECIFICATIONS
Other manuals for this machine
Save 10% on 2 manuals, 15% on 3 or more. Other manuals for the D155AX-5 are listed below. Editions cover different serial number ranges: check the serial coverage and tick only the ones that match your machine.
Added to your cart. View cart
This is an operator's manual
Here's how it compares to the other manual types.
Service manual
Factory repair procedures and technical information such as specifications, troubleshooting, and wiring and hydraulic diagrams, for the models and systems the manual covers. See What's inside for its topics.
Operator's manual
Safe operation, controls, maintenance schedules, lubrication points, inspections, and basic checks. Repair procedures are in the service manual.
Parts manual
Illustrated diagrams with factory part numbers for identifying components and ordering parts. Repair procedures are in the service manual.
What it's used for
Factory manual for in-house farm and construction shop use. Straightforward, complete, and easy to follow. It contains the OEM information dealership service departments and parts counters use to diagnose problems, identify components, and perform maintenance or repairs correctly.
Service shops and owner/operators who repair their own equipment
Identifying correct parts and seeing how assemblies come apart and go back together
Keeping equipment running with less downtime
Factory manual, 303 pages
Quantity one is the manual described above.
Fast free USA shipping
Ships in 1 business day.
60-day returns
Free if the mistake is ours. A manual ordered in error must come back unopened in its shrink-wrap; you pay return shipping and a 20% restocking fee applies. Return policy
Binder not included
Manuals over about 300 pages may need a standard 3-ring binder, which you can buy locally to keep the pages organized for shop use.
Other editions and similar models
Questions about model, serial number, engine coverage or contents? Contact us before purchasing and we'll help confirm it's the right manual. Please verify the manual type, machine model, serial number range and engine coverage before purchasing: manuals ordered in error carry a 20% restocking fee (return policy).