Kubota B2150HSD Tractor Parts Manual
311 pages · Publication B2150HSD
Added to your cart. View cart
- Models
- B2150HSD
- Manual type
- Parts Manual
- Pages
- 311
- Publication
- B2150HSD
- Condition
- Brand new
What's inside
From the manual's own table of contents: 137 topics. See sample pages (PDF, 206 KB)
- Instructions for Parts Books
- |ALL PRODUCT INDEX
- CRANKCASE
- OIL PAN
- PISTON/CRANKSHAFT
- MAIN BEARING CASE
- FLYWHEEL
- CYLINDER HEAD
- VALVE/ROCKER ARM
- NOZZLE HOLDER
- NOZZLE HOLDER [COMPONENT PARTS]
- CYLINDER HEAD COVER
- INLET MANIFOLD
- EXHAUST MANIFOLD
- CAMSHAFT
- GEAR CASE
- WATER PUMP
- WATER FLANGE/THERMOSTAT
- FUEL CAMSHAFT
- INJECTION PUMP
- INJECTION PUMP [COMPONENT PARTS]
- ENGINE STOP LEVER
- SPEED CONTROL PLATE
- GOVERNOR
Show all 137 topics
- UPPER GASKET KIT
- LOWER GASKET KIT
- TENSION PULLEY [CA]
- DYNAMO [A][AU][NZ]
- ALTERNATOR [CA]
- DYNAMO [A][AU][NZ] [COMPONENT PARTS]
- ALTERNATOR [CA] [COMPONENT PARTS]
- CLUTCH
- HYDRAULIC GEAR PUMP
- HYDRAULIC GEAR PUMP [COMPONENT PARTS]
- AIR CLEANER
- AIR CLEANER [COMPONENT PARTS]
- MUFFLER
- ENGINE STOP ROD
- ACCELERATOR LEVER
- FUEL TANK
- FUEL PIPE 1
- FUEL FILTER
- FUEL PIPE 2
- WATER PIPE
- RADIATOR
- STARTER
- STARTER [COMPONENT PARTS]
- BATTERY
- LIGHT
- WORKING LIGHT [OPTION]
- PANEL/SWITCH
- PANEL BOARD [COMPONENT PARTS]
- WIRE HARNESS [A][AU][NZ]
- WIRE HARNESS [CA]
- CLUTCH ROD
- CLUTCH PEDAL
- CLUTCH HOUSING
- TRANSMISSION CASE
- TRANSMISSION CASE COVER
- HST [COMPONENT PARTS]
- PROPELLER SHAFT
- 1ST SHAFT/2ND SHAFT
- 3RD SHAFT
- 4TH SHAFT
- FRONT DRIVE SHAFT/6TH SHAFT
- 7TH SHAFT
- PTO SHAFT
- MID PTO
- FRONT PTO [OPTION]
- NEUTRAL HOLDER
- SPEED CONTROL PEDAL
- SPEED CHANGE PLATE
- SHIFT SET LEVER
- RANGE GEAR SHIFT LEVER
- RANGE GEAR SHIFT FORK
- FRONT WHEEL DRIVE LEVER/PTO LEVER
- BI-SPEED TURN LEVER [WITH BI-SPEED TURN]
- FRONT DRIVE FORK
- PTO FORK SHAFT
- REAR DIFFERENTIAL
- DIFF.LOCK PEDAL
- REAR AXLE
- REAR AXLE CASE
- BRAKE
- BRAKE ROD
- BRAKE PEDAL
- BRAKE INTERLOCKER
- BEVEL GEAR SHAFT
- FRONT AXLE CASE
- BEVEL GEAR CASE
- FRONT AXLE ARM
- FRONT DIFFERENTIAL [W/0 BI-SPEED TURN]
- FRONT DIFFERENTIAL [WITH BI-SPEED TURN]
- CLUTCH DISK [WITH BI-SPEED TURN]
- GEAR CASE [WITH BI-SPEED TURN]
- BI-SPEED TURN CASE [WITH BI-SPEED TURN]
- SHIFT LEVER [WITH BI-SPEED TURN]
- FRONT DRIVE SHAFT
- FRONT WHEEL (6-12)
- FRONT WHEEL (A6-12)
- FRONT AXEL FRAME
- FRONT WEIGHT BRACKET [OPTION]
- KUNCKLE ARM
- MANUAL STEERING
- POWER STEERING
- MANUAL STEERING [COMPONENT PARTS]
- POWER STEERING [COMPONENT PARTS]
- HYDRAULIC PIPE (PS)
- HYDRAULIC PIPE (SUCTION)
- HYDRAULIC PIPE (DELIVERY/RETURN)
- HYDRAULIC BLOCK [COMPONENT PARTS]
- HYDRAULIC PIPE (CHARGE)
- LIFT ARM
- HYD.CYLINDER CAP
- CONTROL VALVE
- CONTROL VALVE1 [COMPONENT PARTS]
- CONTROL VALVE2 [COMPONENT PARTS]
- CONTROL VALVE3 [COMPONENT PARTS]
- TOP LINK
- LOWER LINK/LIFT ROD
- CHECK CHAIN
- HITCH
- DRAWBAR
- HOOD (BONNET)
- LACE
- HOOD (BONNET) COVER REAR
- HOOD (BONNET) FRONT
- HOOD (BONNET) SIDE
- DUST COVER
- HOOD (BONNET) SUPPORT
- FENDER
- SEAT
- STEP
- ROPS [A][CA]
- LABEL 1
- LABEL 2
- ACCESSORIES AND SERVICE PARTS
Inside this manual
Real pages from this parts manual (311 pages). Open the sample pages (PDF, 206 KB)
- Parts illustration, page 267: CONTROL VALVE1 [COMPONENT PARTS]
- Parts illustration, page 283: HOOD (BONNET)
- Parts illustration, page 299: FENDER
This is a parts manual
Here's how it compares to the other manual types.
Service manual
Factory repair procedures and technical information such as specifications, troubleshooting, and wiring and hydraulic diagrams, for the models and systems the manual covers. See What's inside for its topics.
Operator's manual
Safe operation, controls, maintenance schedules, lubrication points, inspections, and basic checks. Repair procedures are in the service manual.
Parts manual
Illustrated diagrams with factory part numbers for identifying components and ordering parts. Repair procedures are in the service manual.
What it's used for
Factory manual for in-house farm and construction shop use. Straightforward, complete, and easy to follow. It contains the OEM information dealership service departments and parts counters use to diagnose problems, identify components, and perform maintenance or repairs correctly.
Service shops and owner/operators who repair their own equipment
Identifying correct parts and seeing how assemblies come apart and go back together
Keeping equipment running with less downtime
Factory manual, 311 pages
Quantity one is the manual described above.
Fast free USA shipping
Ships in 1 business day.
60-day returns
Free if the mistake is ours. A manual ordered in error must come back unopened in its shrink-wrap; you pay return shipping and a 20% restocking fee applies. Return policy
Binder not included
Manuals over about 300 pages may need a standard 3-ring binder, which you can buy locally to keep the pages organized for shop use.
Questions about model, serial number, engine coverage or contents? Contact us before purchasing and we'll help confirm it's the right manual. Please verify the manual type, machine model, serial number range and engine coverage before purchasing: manuals ordered in error carry a 20% restocking fee (return policy).