Kubota B2410HSD Tractor Parts Manual
335 pages · Publication B2410HSD
Added to your cart. View cart
- Models
- B2410HSD
- Manual type
- Parts Manual
- Pages
- 335
- Publication
- B2410HSD
- Condition
- Brand new
What's inside
From the manual's own table of contents: 139 topics. See sample pages (PDF, 185 KB)
- Instructions for Parts Books
- CRANKCASE
- OIL PAN
- CYLINDER HEAD
- GEAR CASE
- HEAD COVER
- OIL FILTER
- DIPSTICK AND GUIDE
- MAIN BEARING CASE
- CAMSHAFT AND IDLE GEAR SHAFT
- PISTON AND CRANKSHAFT
- FLYWHEEL
- CLUTCH
- FUEL CAMSHAFT AND GOVERNOR SHAFT
- ENGINE STOP LEVER
- INJECTION PUMP
- GOVERNOR
- SPEED CONTROL PLATE
- NOZZLE HOLDER AND GLOW PLUG
- NOZZLE HOLDER [COMPONENT PARTS]
- FUEL PUMP(MECHANICAL)
- DYNAMO AND PULLEY
- DYNAMO [COMPONENT PARTS]
- WATER FLANGE AND THERMOSTAT
Show all 139 topics
- WATER PUMP
- VALVE AND ROCKER ARM
- INLET MANIFOLD
- EXHAUST MANIFOLD
- AIR CLEANER
- MUFFLER
- HYDRAULIC PUMP
- HYDRAULIC PUMP [COMPONENT PARTS]
- UPPER GASKET KIT
- LOWER GASKET KIT
- ALTERNATOR KIT
- ALTERNATOR [COMPONENT PARTS]
- ACCELERATOR LEVER
- FUEL TANK
- FUEL PIPE
- FUEL FILTER [COMPONENT PARTS]
- WATER PIPE
- RADIATOR [4WD] [EXCEPT[AU]]
- RESERVE TANK
- STOP SOLENOID
- STARTER
- STARTER [COMPONENT PARTS]
- BATTERY [EXCEPT[AU]]
- SWITCH
- PANEL BOARD
- PANEL BOARD [COMPONENT PARTS]
- HEAD LIGHT
- HAZARD LIGHT
- TAIL LIGHT
- ELECTRICAL WIRING
- CLUTCH ROD
- CLUTCH PEDAL
- CLUTCH HOUSING [4WD]
- FRONT FRAME [4WD]
- CENTER FRAME
- TRANSMISSION CASE
- DIFFERENTIAL GEAR CASE
- REAR AXLE CASE [EXCEPT[BI-SPEED TURN TYPE]]
- CLUTCH SHAFT
- PROPELLER SHAFT
- HST [COMPONENT PARTS]
- FRONT SHAFT
- PTO SHAFT
- MID PTO
- REAR DIFFERENTIAL
- FRONT WHEEL PROPELLER SHAFT [4WD]
- 2ND SHAFT
- 3RD SHAFT
- 4TH SHAFT
- RANGE GEAR SHIFT FORK
- PTO GEAR SHIFT FORK
- DIFFERENTIAL LOCK SHIFT FORK
- REAR AXLE
- BRAKE
- BRAKE ROD 1
- PARKING BRAKE LEVER [EXCEPT[AU]]
- SPEED SET LEVER
- NEUTRAL HOLDER LINK
- SPEED CONTROL PEDAL
- RANGE GEAR SHIFT LEVER
- FRONT WHEEL DRIVE LEVER [4WD]
- PTO GEAR SHIFT LEVER
- HYDRAULIC CONTROL LEVER
- BRAKE PEDAL
- DIFFERENTIAL LOCK PEDAL
- FRONT AXLE CASE [4WD] [EXCEPT[BI-SPEED TURN TYPE]]
- FRONT DIFFERENTIAL[4WD][EXCEPT[BI-SPEED TURN TYPE]]
- DIFFERENTIAL GEAR SHAFT [4WD]
- BEVEL GEAR CASE [4WD]
- FRONT AXLE [4WD]
- FRONT DRIVE SHAFT[4WD][EXCEPT[BI-SPEED TURN TYPE]]
- KNUCKLE ARM [4WD]
- DRAG LINK
- TIE ROD [4WD]
- STEERING HANDLE
- STEERING POST
- HYDRAULIC PUMP(PS)
- HYDRAULIC PUMP(PS) [COMPONENT PARTS]
- HYDRAULIC OIL LINE(SUCTION)
- HYDRAULIC OIL LINE(DELIVERY)
- HYDRAULIC OIL LINE(STEERING)
- HYDRAULIC OIL LINE (HST)
- HYDRAULIC OIL LINE (OIL COOLER)
- HYDRAULIC OIL LINE (F/M)
- HYDRAULIC CYLINDER
- HYDRAULIC PISTON/LIFT ARM
- FEED BACK LEVER
- CONTROL VALVE
- CONTROL VALVE [COMPONENT PARTS]
- 3-POINT LINKAGE 2(LIFT ROD)
- LOWER LINK
- 3-POINT LINKAGE 1(LOWER LINK)
- CHECK CHAIN
- DRAWBAR
- HITCH
- PTO PROTECTOR [EXCEPT[AU]]
- FRONT GRILLE [EXCEPT[AU]]
- BONNET
- PANEL COVER
- SIDE COVER [EXCEPT[AU]]
- SHUTTER PLATE
- FENDER [EXCEPT[BI-SPEED TURN TYPE]]
- FENDER STAY [EXCEPT[BI-SPEED TURN TYPE]]
- FLOOR SEAT
- SEAT SUPPORT
- STEP
- ROPS KIT (RIGID TYPE)
- SMV EMBLEM
- FRONT WHEEL (7-12) [EXCEPT[AU]]
- LABEL [4WD] [EXCEPT[BI-SPEED TURN TYPE]] [A]
- LABEL [4WD] [EXCEPT[BI-SPEED TURN TYPE]] [CA]
- ACCESSORIES AND SERVICE PARTS
- WARKING LIGHT KIT [OPTION]
- POWER STEERING HOSE KIT [OPTION]
- ROPS KIT (FOLDABLE TYPE) [OPTION]
Inside this manual
Real pages from this parts manual (335 pages). Open the sample pages (PDF, 185 KB)
- Parts illustration, page 16: GEAR CASE
- Parts illustration, page 281: FRONT GRILLE [EXCEPT[AU]]
- Parts illustration, page 321: REAR WHEEL (12-16.5) [EXCEPT[AU]]
This is a parts manual
Here's how it compares to the other manual types.
Service manual
Factory repair procedures and technical information such as specifications, troubleshooting, and wiring and hydraulic diagrams, for the models and systems the manual covers. See What's inside for its topics.
Operator's manual
Safe operation, controls, maintenance schedules, lubrication points, inspections, and basic checks. Repair procedures are in the service manual.
Parts manual
Illustrated diagrams with factory part numbers for identifying components and ordering parts. Repair procedures are in the service manual.
What it's used for
Factory manual for in-house farm and construction shop use. Straightforward, complete, and easy to follow. It contains the OEM information dealership service departments and parts counters use to diagnose problems, identify components, and perform maintenance or repairs correctly.
Service shops and owner/operators who repair their own equipment
Identifying correct parts and seeing how assemblies come apart and go back together
Keeping equipment running with less downtime
Factory manual, 335 pages
Quantity one is the manual described above.
Fast free USA shipping
Ships in 1 business day.
60-day returns
Free if the mistake is ours. A manual ordered in error must come back unopened in its shrink-wrap; you pay return shipping and a 20% restocking fee applies. Return policy
Binder not included
Manuals over about 300 pages may need a standard 3-ring binder, which you can buy locally to keep the pages organized for shop use.
Questions about model, serial number, engine coverage or contents? Contact us before purchasing and we'll help confirm it's the right manual. Please verify the manual type, machine model, serial number range and engine coverage before purchasing: manuals ordered in error carry a 20% restocking fee (return policy).