Kubota B7410D Tractor Parts Manual
339 pages · Publication B7410D
Added to your cart. View cart
- Models
- B7410D
- Manual type
- Parts Manual
- Pages
- 339
- Publication
- B7410D
- Condition
- Brand new
What's inside
From the manual's own table of contents: 145 topics. See sample pages (PDF, 194 KB)
- Instructions for Parts Books
- CRANKCASE
- OIL PAN
- CYLINDER HEAD
- GEAR CASE
- HEAD COVER
- OIL FILTER
- DIPSTICK AND GUIDE
- OIL PUMP
- MAIN BEARING CASE
- CAMSHAFT AND IDLE GEAR SHAFT
- PISTON AND CRANKSHAFT
- FLYWHEEL
- FUEL CAMSHAFT AND GOVERNOR SHAFT
- IDLE APPARATUS
- INJECTION PUMP
- GOVERNOR
- SPEED CONTROL PLATE
- NOZZLE HOLDER AND GLOW PLUG
- NOZZLE HOLDER [COMPONENT PARTS]
- FUEL PUMP(MECHANICAL)
- WATER FLANGE AND THERMOSTAT
- WATER PUMP
- VALVE AND ROCKER ARM
Show all 145 topics
- INLET MANIFOLD
- EXHAUST MANIFOLD
- AIR CLEANER
- MUFFLER
- UPPER GASKET KIT [OPTION]
- LOWER GASKET KIT [OPTION]
- PISTON KIT [OPTION]
- ACCELERATOR LEVER
- FUEL TANK
- FUEL PIPE
- FUEL FILTER [COMPONENT PARTS]
- WATER PIPE
- RADIATOR [EXCEPT [AU] [NZ]]
- RADIATOR [AU] [NZ]
- RESERVE TANK [EXCEPT [AU] [NZ]]
- RESERVE TANK [AU] [NZ]
- STOP SOLENOID
- DYNAMO
- DYNAMO [COMPONENT PARTS]
- STARTER
- STARTER [COMPONENT PARTS]
- BATTERY
- SWITCH
- PANEL BOARD
- PANEL BOARD [COMPONENT PARTS]
- HEAD RIGHT
- HAZARD LIGHT
- TAIL LIGHT
- WINKER LAMP
- ELECTRICAL WIRING
- CLUTCH
- CLUTCH ROD
- CLUTCH PEDAL
- CLUTCH HOUSING
- CLUTCH DIPSTICK AND GUIDE
- CENTER FRAME
- TRANSMISSION CASE
- DIFFERENTIAL GEAR CASE
- REAR AXLE CASE
- CLUTCH SHAFT
- PROPELLER SHAFT
- FRONT SHAFT
- PTO SHAFT
- REAR DIFFERENTIAL
- FRONT WHEEL PROPELLER SHAFT
- 2ND SHAFT
- 3RD SHAFT
- 4TH SHAFT
- MAIN GEAR SHIFT FORK
- RANGE GEAR SHIFT FORK
- PTO GEAR SHIFT FORK
- DIFFERENTIAL LOCK SHIFT FORK
- REAR AXLE
- BRAKE
- BRAKE ROD
- PARKING BRAKE LEVER [EXCEPT [AU] [NZ]]
- PARKING BRAKE LEVER [AU] [NZ]
- MAIN GEAR SHIFT LEVER
- RANGE GEAR SHIFT LEVER
- FRONT WHEEL DRIVE LEVER
- PTO GEAR SHIFT LEVER
- HYDRAULIC CONTROL LEVER
- BRAKE PEDAL
- DIFFERENTIAL LOCK PEDAL
- FRONT AXLE FRAME
- FRONT AXLE CASE
- FRONT DIFFERENTIAL
- DIFFERENTIAL GEAR SHAFT
- BEVEL GEAR CASE
- FRONT AXLE
- FRONT DRIVE SHAFT
- KNUCKLE ARM
- DRAG LINK
- TIE ROD
- STEERING HANDLE
- STEERING POST
- STEERING CONTROLLER
- STEERING CONTROLLER [COMPONENT PARTS]
- HYDRAULIC PUMP
- HYDRAULIC PUMP [COMPONENT PARTS]
- HYDRAULIC OIL LINE(SUCTION)
- HYDRAULIC OIL LINE(DELIVERY)
- HYDRAULIC CYLINDER
- HYDRAULIC PISTON/LIFT ARM
- FEED BACK LEVER
- CONTROL VALVE
- CONTROL VALVE [COMPONENT PARTS]
- 3-POINT LINKAGE 2(LIFT ROD)
- LOWER LINK
- 3-POINT LINKAGE 1(TOP LINK)
- CHECK CHAIN
- DRAWBAR
- REAR HITCH
- PTO PROTECTOR [EXCEPT [AU] [NZ]]
- PTO PROTECTOR [AU] [NZ]
- FRONT GRILLE [A] [CA]
- FRONT GRILLE [AU] [NZ]
- BONNET
- PANEL COVER
- SIDE COVER
- SHUTTER PLATE [EXCEPT [AU] [NZ]]
- SHUTTER PLATE [AU] [NZ]
- LEVER GUIDE
- FENDER [EXCEPT [AU] [NZ]]
- FENDER [AU] [NZ]
- FENDER STAY
- FLOOR SEAT
- SEAT SUPPORT
- STEP
- ROPS(RIGID TYPE) [EXCEPT [AU]]
- ROPS(FOLDABLE TYPE) [EXCEPT [AU]]
- ROPS [AU]
- SMV EMBLEM [EXCEPT [AU]]
- FRONT WHEEL(6-12) [EXCEPT [AU] [NZ]]
- LABEL [EXCEPT [AU] [NZ]] [ENGLISH]
- LABEL [EXCEPT [AU] [NZ]] [FRENCH]
- LABEL [AU]
- LABEL [NZ]
- ACCESSORIES AND SERVICE PARTS
- WARKING LIGHT KIT [OPTION]
- WORKING LIGHT KIT [OPTION]
Inside this manual
Real pages from this parts manual (339 pages). Open the sample pages (PDF, 194 KB)
- Parts illustration, page 111: SWITCH
- Parts illustration, page 151: PTO SHAFT
- Parts illustration, page 316: REAR WHEEL(31*15.5-15) [EXCEPT [AU] [NZ]]
This is a parts manual
Here's how it compares to the other manual types.
Service manual
Factory repair procedures and technical information such as specifications, troubleshooting, and wiring and hydraulic diagrams, for the models and systems the manual covers. See What's inside for its topics.
Operator's manual
Safe operation, controls, maintenance schedules, lubrication points, inspections, and basic checks. Repair procedures are in the service manual.
Parts manual
Illustrated diagrams with factory part numbers for identifying components and ordering parts. Repair procedures are in the service manual.
What it's used for
Factory manual for in-house farm and construction shop use. Straightforward, complete, and easy to follow. It contains the OEM information dealership service departments and parts counters use to diagnose problems, identify components, and perform maintenance or repairs correctly.
Service shops and owner/operators who repair their own equipment
Identifying correct parts and seeing how assemblies come apart and go back together
Keeping equipment running with less downtime
Factory manual, 339 pages
Quantity one is the manual described above.
Fast free USA shipping
Ships in 1 business day.
60-day returns
Free if the mistake is ours. A manual ordered in error must come back unopened in its shrink-wrap; you pay return shipping and a 20% restocking fee applies. Return policy
Binder not included
Manuals over about 300 pages may need a standard 3-ring binder, which you can buy locally to keep the pages organized for shop use.
Questions about model, serial number, engine coverage or contents? Contact us before purchasing and we'll help confirm it's the right manual. Please verify the manual type, machine model, serial number range and engine coverage before purchasing: manuals ordered in error carry a 20% restocking fee (return policy).