Kubota M4950DT-S Tractor Parts Manual
314 pages · Publication M4950DT-S
Added to your cart. View cart
- Models
- M4950DT-S
- Manual type
- Parts Manual
- Pages
- 314
- Publication
- M4950DT-S
- Condition
- Brand new
What's inside
From the manual's own table of contents: 150 topics. See sample pages (PDF, 73 KB)
- Instructions for Parts Books
- CRANKCASE
- OIL PAN (2WD)
- OIL PAN (4WD)
- PISTON AND CRANKSHAFT
- MAIN BEARING CASE
- FLYWHEEL
- CYLINDER HEAD
- VALVE AND ROCKER ARM
- NOZZLE HOLDER AND FUEL PIPE
- NOZZLE HOLDER [COMPONENT PARTS]
- CYLINDER HEAD COVER
- INLET MANIFOLD
- AIR CLEANER (DOUBLE)
- AIR CLEANER (DOUBLE) [COMPONENT PARTS]
- AIR CLEANER SUPPORT
- PRE-CLEANER [OPTION]
- MUFFLER AND EXHAUST MANIFOLD
- UNDER MUFFLER [OPTION]
- CAMSHAFT
- GEAR CASE
- OIL FILTER [COMPONENT PARTS]
- WATER FLANGE AND THERMOSTAT
- WATER PUMP
Show all 150 topics
- FUEL CAMSHAFT
- INJECTION PUMP
- INJECTION PUMP [COMPONENT PARTS]
- ENGINE STOP LEVER
- SPEED CONTROL PLATE
- GOVERNOR
- HAND ACCELERATOR
- ACCELERATOR PEDAL
- ENGINE STOP ROD
- FUEL TANK
- FUEL TANK SUPPORT
- FUEL PIPE
- FUEL FILTER [COMPONENT PARTS]
- RADIATOR
- WATER PIPE
- STARTER
- DYNAMO AND FAN
- STARTER [COMPONENT PARTS]
- DYNAMO [COMPONENT PARTS]
- BATTERY
- PANEL BOARD
- PANEL BOARD [COMPONENT PARTS]
- SWITCH 1
- LIGHT 1
- LIGHT 2
- WORKING LIGHT AND TRAILER HARNESS [OPTION]
- WIRE HARNESS
- CLUTCH
- CLUTCH FORK
- CLUTCH PEDAL
- PTO CLUTCH FORK
- PTO CLUTCH LEVER
- CLUTCH HOUSING 1
- CLUTCH HOUSING 2
- TRANSMISSION CASE
- TRANSMISSION CASE REAR COVER
- PTO PROPELLER SHAFT
- FIRST SHAFT
- COUNTER SHAFT
- HI-LO GEAR SHAFT
- HALF GEAR SHAFT AND FRONT DRIVE SHAFT
- BACK IDLE SHAFT
- PTO DRIVE SHAFT
- PTO SHAFT
- MAIN GEAR SHIFT LEVER
- MAIN GEAR SHIFT FORK
- HI-LO GEAR SHIFT FORK
- HI-LO GEAR SHIFT LEVER
- HALF GEAR SHIFT FORK
- PTO GEAR SHIFT LEVER
- PTO SHIELD COVER
- FRONT WHEEL DRIVE LEVER
- BEVEL GEAR (REAR)
- DIFFERENTIAL (REAR)
- DIFF.LOCK PEDAL
- REAR AXLE CASE
- REAR AXLE
- BRAKE
- BRAKE PEDAL
- BRAKE ROD
- PARKING BRAKE LEVER
- FRONT DRIVE SHAFT
- PROPELLER SHAFT
- FRONT DIFF.CASE BRACKET
- FRONT DIFF.CASE
- BEVEL GEAR (FRONT)
- DIFFERENTIAL (FRONT)
- DIFF.LOCK CLUTCH
- DIFF.LOCK ROD
- DIFF.GEAR SHAFT
- BEVEL GEAR CASE
- FRONT WHEEL CASE
- FRONT AXLE
- FRONT AXLE BRACKET
- STEERING LINKAGE
- STEERING CYLINDER [COMPONENT PARTS]
- STEERING HANDLE
- POWER STEERING OIL TANK
- POWER STEERING OIL PUMP
- POWER STEERING OIL PIPE
- STEERING CONTROLLER [COMPONENT PARTS]
- HYD.CYLINDER BODY
- HYD.CYLINDER LINER
- DOWN SPEED ADJUSTING ROD
- LIFT LEVER
- HYDRAULIC SYSTEM 1
- HYDRAULIC SYSTEM 2
- HYDRAULIC SYSTEM 3
- HYD.CONTROL LEVER GUIDE
- DRAFT & POSITION CONTROL LEVER
- HYDRAULIC PUMP AND SUCTION PIPE
- HYDRAULIC PUMP [COMPONENT PARTS]
- DELIVERY PIPE
- HYDRAULIC OUTLET BLOCK [OPTION]
- AUX.CONTROL VALVE
- AUX.CONTROL VALVE HOSE
- AUX.CONTROL VALVE [OPTION]
- AUX.CONTROL VALVE [COMPONENT PARTS]
- HYDRAULIC LIFT LINK 1 (LOWER LINK)
- TELESCOPE LOWER LINK [OPTION]
- HYDRAULIC LIFT LINK 2 (CHECK CHAIN)
- HYDRAULIC LIFT LINK 3 (LIFT ROD RH)
- HYDRAULIC LIFT LINK 4 (LIFT ROD LH)
- HYDRAULIC LIFT LINK 5 (TOP LINK)
- TOP LINK BRACKET
- SWINGING DRAWBAR
- DRAWBAR HITCH [OPTION]
- HOOD FRONT (BONNET FRONT)
- HOOD (BONNET)
- HOOD SIDE 1 (BONNET SIDE 1)
- HOOD SIDE 2 (BONNET SIDE 2)
- HOOD REAR (BONNET REAR)
- HANDRAIL [OPTION]
- PANEL AND REAR COVER
- FENDER
- FENDER BRACKET
- SEAT
- SEAT [COMPONENT PARTS]
- STEP
- AID STEP
- CENTER FRAME
- HOUSING COVER
- TOOL BOX
- LABEL 1 (ENGLISH)
- LABEL 2 (ENGLISH)
- ACCESSORIES AND SERVICE PARTS
This is a parts manual
Here's how it compares to the other manual types.
Service manual
Factory repair procedures and technical information such as specifications, troubleshooting, and wiring and hydraulic diagrams, for the models and systems the manual covers. See What's inside for its topics.
Operator's manual
Safe operation, controls, maintenance schedules, lubrication points, inspections, and basic checks. Repair procedures are in the service manual.
Parts manual
Illustrated diagrams with factory part numbers for identifying components and ordering parts. Repair procedures are in the service manual.
What it's used for
Factory manual for in-house farm and construction shop use. Straightforward, complete, and easy to follow. It contains the OEM information dealership service departments and parts counters use to diagnose problems, identify components, and perform maintenance or repairs correctly.
Service shops and owner/operators who repair their own equipment
Identifying correct parts and seeing how assemblies come apart and go back together
Keeping equipment running with less downtime
Factory manual, 314 pages
Quantity one is the manual described above.
Fast free USA shipping
Ships in 1 business day.
60-day returns
Free if the mistake is ours. A manual ordered in error must come back unopened in its shrink-wrap; you pay return shipping and a 20% restocking fee applies. Return policy
Binder not included
Manuals over about 300 pages may need a standard 3-ring binder, which you can buy locally to keep the pages organized for shop use.
Questions about model, serial number, engine coverage or contents? Contact us before purchasing and we'll help confirm it's the right manual. Please verify the manual type, machine model, serial number range and engine coverage before purchasing: manuals ordered in error carry a 20% restocking fee (return policy).