Kubota R400(B) Tractor Parts Manual
287 pages · Publication R400(B)_2
Added to your cart. View cart
- Models
- R400(B)
- Manual type
- Parts Manual
- Pages
- 287
- Publication
- R400(B)_2
- Condition
- Brand new
_2.jpg)
What's inside
From the manual's own table of contents: 138 topics. See sample pages (PDF, 225 KB)
- Instructions for Parts Books
- |ALL PRODUCT INDEX
- CRANK CASE
- OIL PAN
- PISTON AND CRANK SHAFT
- MAIN BEARING CASE
- CAM SHAFT
- CYLINDER HEAD
- VALVE AND ROCKER ARM
- CYLINDER HEAD COVER
- GEAR CASE
- INLET MANIFOLD
- NOZZLE HOLDER AND GLOW PLUG
- NOZZLE HOLDER (SECTION PARTS)
- FUEL CAMSHAFT
- INJECTION PUMP
- INJECTION PUMP (SECTION PARTS)
- ENGINE STOP LEVER
- SPEED CONTROL PLATE
- GOVERNOR
- WATER FLANGE
- WATER PUMP
- DYNAMO
- DYNAMO (SECTION PARTS)
Show all 138 topics
- FLYWHEEL AND STARTER
- SUB OIL PAN
- ENGINE BRACKET
- AIR CLEANER
- MUFFLER AND EXHAUST MANIFOLD
- ACCEL AND STOP ROD [KTC KTCL]
- FUEL PIPING
- FUEL TANK
- RADIATER & WATER PIPE
- BATTERY
- SWITCH (1) AND PANEL
- SWITCH (2) AND REGULATOR
- LIGHT
- ELECTRICAL WIRING
- TRANSMISSION CASE (1)
- TRANSMISSION CASE (2)
- CLUTCH [C1 C2]
- COUPLUNG
- PLANETARY CARRIER
- CLUTCH SHAFT (1)
- CLUTCH SHAFT (2)
- TRANSFER (DRIVE SHAFT)
- TRANSFER (HYDRAULIC PUMP)
- SPEED CHANGE LEVER
- SPEED CHANGE LINKAGE SYSTEM
- DRIVE SHAFT
- DIFFERENTIAL CASE (FRONT)
- SPIRAL BEVEL GEAR (FRONT)
- DIFFERENTIAL (FRONT)
- AXLE (FRONT)
- DIFFERENTIAL CASE (REAR)
- SPIRAL BEVEL GEAR (REAR)
- DIFFERENTIAL (REAR)
- AXLE (REAR)
- TIRE AND WHEEL
- STEERING CYLINDER AND CONTROLLER (NEW TYPE)
- STEERING CONTROLLER (SECTION PARTS) >=20017 (NEW TYPE)
- STEERING CONTROLLER (SECTION PARTS) <=20016 (OLD TYPE)
- STEERING CYLINDER (SECTION PARTS)
- STEERING HANDLE
- BRAKE
- BRAKE PEDAL
- INCHING PEDAL
- BRAKE PIPING
- PARKING BRAKE
- PARKING LEVER
- HYDRAULIC PUMP
- HYDRAULIC PUMP (SECTION PARTS)
- FLOW PRIORITY VALVE (SECTION PARTS)
- CONTROL VALVE & SECTION PARTS
- CONTROL VALVE SPOOL SECTION
- CLUTCH VALVE
- MODULATION VALVE
- OIL TANK
- OIL COOLER
- TILT & LIFT CYLINDER
- TILT CYLINDER (SECTION PARTS)
- LIFT CYLINDER (SECTION PARTS)
- CONTROL LEVER (SHOVEL)
- CONTROL LEVER (S/P)
- SAFETY ROCK LEVER
- OIL PIPING (SUCTION, FILTER)
- OIL PIPING (DELIVERY)
- OIL PIPING (RETURN)
- OIL PIPING (REAR PTO)
- OIL PIPING (LIFT CYLINDER)
- OIL PIPING (LIFT CYLINDER-RH)
- OIL PIPING (LIFT CYLINDER-LH)
- OIL PIPING (TILT CYLINDER)
- OIL PIPING (S/P-1)
- OIL PIPING (S/P-2)
- OIL PIPING (TRANSMISSION-1)
- OIL PIPING (TRANSMISSION-2)
- FRONT FRAME
- REAR FRAME (1)
- REAR FRAME (2)
- FLOOR BOARD
- REAR COVER (1)
- SEAT FRAME
- REAR COVER (2)
- BONNET SPONGE [KTC KTCL KTA]
- WEIGHT
- SHOVEL FRAME
- TILT ARM
- MULTI COUPLER BUCKET [KTCL]
- CANOPY (ROPS) [KTC KTCL KTA]
- SEAT
- LABEL [KTC KTCL]
- SLIDE FRAME
- CONTROL VALVE STAND
- SWING BRACKET
- BOOM
- BUCKET LINK
- BUCKET
- CONTROL VALVE (J.D)
- CONTROL VALVE (J.D) SPOOL SECTION
- BOOM CYLINDER & SECTION PARTS
- ARM CYLINDER & SECTION PARTS
- BUCKET CYLINDER & SECTION PARTS
- SWING CYLINDER & SECTION PARTS
- SLIDE LOCK CYLINDER & SECTION PARTS
- OUT LIGGER CYLINDER & SECTION PARTS
- OIL PIPING (QUICK COUPLER)
- OIL PIPING (OUT LIGGER)
- OIL PIPING (SLIDE LOCK)
- OIL PIPING (BOOM)
- OIL PIPING (ARM)
- OIL PIPING (BUCKET)
- OIL PIPING (SWING)
- CONTROL LEVER (OUT LIGGER & SLIDE LOCK)
- CONTROL LEVER (OPERATING)
- CONTROL LEVER (SAFETY LOCK LEVER)
- LABEL
- ACCESSORY AND SERVICE PARTS
Inside this manual
Real pages from this parts manual (287 pages). Open the sample pages (PDF, 225 KB)
- Parts illustration, page 38: ENGINE STOP LEVER
- Parts illustration, page 50: DYNAMO (SECTION PARTS)
- Parts illustration, page 62: ACCEL AND STOP ROD [KTC KTCL]
This is a parts manual
Here's how it compares to the other manual types.
Service manual
Factory repair procedures and technical information such as specifications, troubleshooting, and wiring and hydraulic diagrams, for the models and systems the manual covers. See What's inside for its topics.
Operator's manual
Safe operation, controls, maintenance schedules, lubrication points, inspections, and basic checks. Repair procedures are in the service manual.
Parts manual
Illustrated diagrams with factory part numbers for identifying components and ordering parts. Repair procedures are in the service manual.
What it's used for
Factory manual for in-house farm and construction shop use. Straightforward, complete, and easy to follow. It contains the OEM information dealership service departments and parts counters use to diagnose problems, identify components, and perform maintenance or repairs correctly.
Service shops and owner/operators who repair their own equipment
Identifying correct parts and seeing how assemblies come apart and go back together
Keeping equipment running with less downtime
Factory manual, 287 pages
Quantity one is the manual described above.
Fast free USA shipping
Ships in 1 business day.
60-day returns
Free if the mistake is ours. A manual ordered in error must come back unopened in its shrink-wrap; you pay return shipping and a 20% restocking fee applies. Return policy
Other editions and similar models
Questions about model, serial number, engine coverage or contents? Contact us before purchasing and we'll help confirm it's the right manual. Please verify the manual type, machine model, serial number range and engine coverage before purchasing: manuals ordered in error carry a 20% restocking fee (return policy).