Linde H14T, H16T, H18T, H20-600T, H20T LPG Forklift Operator's Manual
260 pages · Publication 391-807-1051
Added to your cart. View cart
- Models
- H14T, H16T, H18T, H20-600T, H20T LPG
- Manual type
- Operator's Manual
- Pages
- 260
- Publication
- 391-807-1051
- Condition
- Brand new
What's inside
From the manual's own table of contents: 94 topics. See sample pages (PDF, 337 KB)
- Technical Description
- Truck operation with a bucket
- Takeover of forklift truck
- In the case of tip-over
- Operation of industrial trucks in plant area
- Regulations
- Safety guidelines for liquid gas (excerpt)
- Safety precautions for handling ignition systems
- Instructions before fitting attachments
- Rating plates
- Operating elements
- Instructions for running-in
- Checks before starting work
- Adjust the driver’s seat
- Adjusting the steering column
- Setting the clock
- Engine (two-pedal operation)
- Driving (two-pedal operation)
- Steering system
- Brake system
- Lifting system and attachments (single-lever operation)
- Special equipment
- Adjust driver’s seat with swivel device
- Adjust the driver’s air-sprung seat
Show all 94 topics
- Mast positioning
- Lighting
- Heating, air conditioning
- Before taking up load
- Loading
- Setting down loads
- Transportation by truck or low loading truck
- General
- year
- Inspection and maintenance every 6000 hours or every 3 years
- Inspection and maintenance every 9000 hours or every 4 years
- Inspection and maintenance data
- Changing the LPG cylinder
- Filling the LPG tank (special equipment)
- Coolant
- Tyres
- Check the third auxiliary hydraulic function and safety system (option)
- Inspection and maintenance as required
- Base plate
- Changing wheels
- Tighten the wheel bolts
- Clean the truck
- Change the air filter element
- Cleaning the prefilter (special equipment)
- Change the oil in the oil bath air cleaner (Optional)
- Check tyres for damage and foreign bodies
- Check condition and function of seat belt
- Inspection and maintenance every 500 to 1000 operating hours or each year
- Clean the radiator and hydraulic oil cooler
- Clean wet type air cleaner (Optional)
- Check correct operation of breather valve on the hydraulic oil tank
- Change engine oil filter
- Replace the fuel gas filter
- Checking the LPG system for damage and leaks
- Check the fuel gas settings
- Clean the evaporator / pressure regulator
- Replace the spark plugs
- tion)
- Check pedals
- Check other bearings and joints and oil them
- Check that the control unit is working properly
- Clean and grease the steering axle
- Clean sideshift (special equipment) and grease, check fastening
- function
- Check the pre-tension of the double tubes
- Check hose carrier
- attached securely
- Check the attachment points on the frame, tilt cylinder and steering axle
- Drive axle und wheel engines, check attachment
- Check the fastening on the steering cylinder and axle stub bolt
- Hydraulic system: change filter
- Change ribbed V-belt
- Renew the toothed belt and idler pulley
- Check the drive axle bearing for wear and tear
- Check slide guides on sideshift (special equipment) for wear
- Change hydraulic oil
- Replace the water pump
- Change coolant
- Troubleshooting
- Emergency lowering of fork carriage
- Malfunctions during operation
- Noise emission values
- Basic equipment for LPG page 1
- Basic equipment for LPG page 2
- Basic equipment LPG sheet 3
- Special equipment sheet 2 −windscreen wiper, seat heater
- tion, lift mast positioning
- Special equipment sheet 5 −soot filter, radio
- monitoring, cooling water level monitoring
- Traction, operating and steering hydraulics
Inside this manual
Real pages from this operator's manual (260 pages). Open the sample pages (PDF, 337 KB)
- Controls and operation, page 73: Special equipment
- Maintenance, page 173: Inspection and maintenance every 3000 operating hours or every 2 years
- Specifications, page 213: Technical data 6
- Color page, page 197: Maintenance 5
- Color page, page 216: Technical data
This is an operator's manual
Here's how it compares to the other manual types.
Service manual
Factory repair procedures and technical information such as specifications, troubleshooting, and wiring and hydraulic diagrams, for the models and systems the manual covers. See What's inside for its topics.
Operator's manual
Safe operation, controls, maintenance schedules, lubrication points, inspections, and basic checks. Repair procedures are in the service manual.
Parts manual
Illustrated diagrams with factory part numbers for identifying components and ordering parts. Repair procedures are in the service manual.
What it's used for
Factory manual for in-house farm and construction shop use. Straightforward, complete, and easy to follow. It contains the OEM information dealership service departments and parts counters use to diagnose problems, identify components, and perform maintenance or repairs correctly.
Service shops and owner/operators who repair their own equipment
Identifying correct parts and seeing how assemblies come apart and go back together
Keeping equipment running with less downtime
Factory manual, 260 pages
Quantity one is the manual described above.
Fast free USA shipping
Ships in 1 business day.
60-day returns
Free if the mistake is ours. A manual ordered in error must come back unopened in its shrink-wrap; you pay return shipping and a 20% restocking fee applies. Return policy
Questions about model, serial number, engine coverage or contents? Contact us before purchasing and we'll help confirm it's the right manual. Please verify the manual type, machine model, serial number range and engine coverage before purchasing: manuals ordered in error carry a 20% restocking fee (return policy).