Linde MX10, MX13-N shunt Forklift Service Manual
381 pages · Publication W8-054-152
Added to your cart. View cart
- Models
- MX10, MX13-N shunt
- Manual type
- Service Manual
- Pages
- 381
- Publication
- W8-054-152
- Condition
- Brand new
What's inside
From the manual's own table of contents: 274 topics. See sample pages (PDF, 449 KB)
- Actual value
- Actual value error
- Actual value potentiometer, offset potentiometer
- Additional lift, removal
- Additional lift cylinder
- Adjusting chart LR80
- Aisle detection, testing
- Aisle detection, mounting the reflectors
- Aisle travel, LR80
- Analogue module, PLC
- Application program, copying, PLC
- Application program, PLC
- Armature shaft
- Attachment
- Automatic operation, LR80
- Ball bearings, travel motor
- Ball bearings, steering motor
- Barrier switches (S20 and S21)
- Battery buffer, LFG
- Battery roller track
- Battery type, FPS
- Battery lock
- Battery status display
- Bearing play, idling wheel
Show all 274 topics
- Binary module, PLC
- Bleeder screw, main lift
- Bleeder screw, additional lift
- Block diagram, operating console
- Block diagram, FPS
- Block diagram, hydraulics
- Block diagram, logic 7A21
- Block diagram, LR80
- Block diagram, standard steering
- Bogie bearing
- Brake lining, replacing
- Brake, removal
- Brake, function
- Brake, generator
- Brake, mech. release
- Brake modes
- Brake amplifier (1U21)
- Brake deceleration
- Braking distance
- Brush spring
- Brush spring, testing
- Carbon dust
- Chain breakage
- Chain breakage function, checking
- Chain joint
- Commutator, travel motor
- Connections, travel motor
- Connector, counting method, LR80
- Control board (3A24)
- Control unit, FPS
- CPU module, PLC
- Curve number, LR80
- Cylinder holder, main lift
- Deadman's switch (1S25)
- Delay parameter
- Detection, improved
- Detection angle <10°
- Detection angle >10°
- Detent control
- DIAG LED, PLC
- Digsy software
- Direction of rotation, travel motor
- Direction of travel, FPS
- Disposal, oils
- Disposal, lubricants
- Drive wheel
- Electrical switchboard
- End stop, handwheel
- Error display, operating console
- Error bit bar, reading out, PLC
- Error class, operating console
- Error message, LR80
- Error memory
- Error memory, error description
- Error memory, error list
- Error memory, deleting
- Eyebolt M8
- Field connection, steering motor
- Field winding, travel motor
- Four-point bearing
- FPS, selecting travel parameters
- FPS, battery type
- FPS, description
- FPS, changing operating hours
- FPS, travel programs
- FPS, deceleration 1, 2 and 3
- FPS, direction of travel
- FPS, error description
- FPS, error list
- FPS, error memory
- FPS, carbon brush monitor
- FPS, power section
- FPS, travel setpoint
- FPS, hydraulic function setpoint
- FPS, reading out set values
- FPS, standard parameter set
- FPS, status displays
- FPS, pin assignment
- FPS, control and logic section
- FPS, temperature monitor
- FPS, summary of all addresses
- FPS, summary of all travel parameters
- Fuse F1, main current switchboard
- Fuse F2, main curernt switchboard
- Gear, removal
- Gear, oil change
- Guide to addresses, FPS
- Guide block, SSG
- Guide rollers, SSG
- Guide rollers, telescopic load carriage
- Guide to chapters
- Guide wire
- Hydraulic unit
- Hydraulic unit, removal
- Hydraulic motor (2M1)
- Interface adapter
- Interlock module 8U40
- Intermediate lift cut-out
- Keypad board 1, 2 and 3
- Language selection, LR80
- Lateral guide rollers, swivel shift fork
- Load carriage
- Load carriage, removal
- Loading-bearing rollers, swivel shift fork
- LR80 parameters, guide
- Lubricating nipple
- Lubricants, guide
- Maintenance work, travel motor
- Maintenance work, steering motor
- Maintenance symbol, operating console
- Manual operation, LR80
- Marker word table, PLC
- Mast yoke
- Mechanical release, brake
- Mica
- Notebook, test numbers, LR80
- Oil drainage screw, gear
- Oil types, guide
- Oil filler cap, gear
- Oil level, checking, hydraulic oil
- Oil temperature
- Oil change, gear
- Operating lever
- Operating lever, removal
- Operating console, versions
- Operating console, operating elements
- Operating console, start-up test
- Operating console, error display
- Operating hours, changing
- Operating hours, display
- Output filter, LFG
- Parameters, storing, LR80
- Parameters, reading out, FPS
- Parameters, programming, FPS
- Parameter changes, PLC
- Parameter settings, TEWAK95
- Pin assignment, control board (3A24)
- Pin assignment, operating console (A29)
- Pin assignment, logic section, FPS
- Pin assignment, safety relay board (7A21)
- Plate offset, ZAG
- PLC, outputs
- PLC, inputs
- PLC, front panel
- PLC, commissioning
- PLC, current flow diagram
- Position switch, combinations
- Position switch plausibility
- Potentiometer, travel
- Potentiometer, hydraulics
- Power chain
- Power unit, travel and pump control system
- Pressure relief valve, HMC-33
- Program, loading into PLC
- Programming adapter
- Programming, LR80
- Programming, PLC
- Programming, preparation, FPS
- Proportional valve, technical data
- Proportional amplifier (2U40)
- Rail travel
- Reflective light barriers
- Relay K35
- Safety relay K33, K34
- Screw fixant
- Sealing ring, gear oil
- Sensor signals, speed sensor
- Service hours
- Setpoint, hydraulic functions
- Setpoints, reading out, FPS
- Setpoint error
- Shaft coupling, swivel shift fork
- Slack chain, checking
- Slack chain
- Sockets, counting method, LR80
- Special workshop
- Speed, travel motor
- Speed sensor, adaptation
- Speed sensor, connections
- Speed sensor, direction of travel
- ST-STAT
- Stability
- Standard parameter set, FPS
- Status symbols, operating console
- Steering bearing
- Steering potentiometer (3R11)
- Steering, adjustment
- Stop buffer, SSG
- Support carriage
- Support rollers
- Switching outputs, LR80
- Switch transistors, LR80
- Swivel shift fork (SSF)
- Swivel shift fork, removal
- Swivel shaft, SSF
- Tank, hydraulic oil
- Technical data, aerial
- Technical data, travel motor
- Technical data, hydraulic motor
- Technical data, steering motor
- Technical data, guide frequency generator
- Telescopic fork
- Telescopic load carriage
- Telescopic mast
- Temperature monitor, travel motor
- Temperature monitor, FPS
- Temperature monitor, pump motor
- Test transmitter, LR80
- Test coil, aerial
- Test connection, manometer
- Test template, steering angle limitation
- Tooth profile play, swivel-shift fork
- Toothed rack, swivel-shift fork
- Toothed shaft, swivel-shift fork
- Track rollers
- Travel motor (1M1)
- Travel motor, removal
- Travel motor, maintenance
- Travel parameter
- Wheel bearing, idling wheel
- Wheel position display
- Wire loop, LFG
- Wire search, LR80
- ZAG (end-of-aisle braking)
- ZAG, inductive
- ZAG, magnetic
- ZAG, reflexli
- Travel motor
- Travel motor, technical data
- Travel motor connections
- Speed sensor
- Speed sensor connections
- Testing the speed sensor
- Temperature sensor integrated in the carbon brush yoke
- Removing the travel motor
- Replacing the travel motor
- Removing the gear
- Changing the gear oil
- Lubricating the bogie bearing
- Replacing the drive wheel
- Carbon brush monitor
- Replacing the carbon brushes
- Checking the brush springs
- Travel motor maintenance
- General
- Cleaning
- Visual inspection, replacing damaged parts
- Checking the brush unit, replacing the carbon brushes
- Commutator
- Bearings
Inside this manual
Real pages from this service manual (381 pages). Open the sample pages (PDF, 448 KB)
- Diagram, page 188: Steering angle limitation
- Troubleshooting, page 253: Operating console A29
- Specifications, page 313: Hydraulic motor
This is a service manual
Here's how it compares to the other manual types.
Service manual
Factory repair procedures and technical information such as specifications, troubleshooting, and wiring and hydraulic diagrams, for the models and systems the manual covers. See What's inside for its topics.
Operator's manual
Safe operation, controls, maintenance schedules, lubrication points, inspections, and basic checks. Repair procedures are in the service manual.
Parts manual
Illustrated diagrams with factory part numbers for identifying components and ordering parts. Repair procedures are in the service manual.
Engine service manuals are sometimes sold separately, since certain machine models were offered with more than one engine option.
What it's used for
Factory manual for in-house farm and construction shop use. Straightforward, complete, and easy to follow. It contains the OEM information dealership service departments and parts counters use to diagnose problems, identify components, and perform maintenance or repairs correctly.
Service shops and owner/operators who repair their own equipment
Identifying correct parts and seeing how assemblies come apart and go back together
Keeping equipment running with less downtime
Factory manual, 381 pages
Quantity one is the manual described above.
Fast free USA shipping
Ships in 1 business day.
60-day returns
Free if the mistake is ours. A manual ordered in error must come back unopened in its shrink-wrap; you pay return shipping and a 20% restocking fee applies. Return policy
Binder not included
Manuals over about 300 pages may need a standard 3-ring binder, which you can buy locally to keep the pages organized for shop use.
Questions about model, serial number, engine coverage or contents? Contact us before purchasing and we'll help confirm it's the right manual. Please verify the manual type, machine model, serial number range and engine coverage before purchasing: manuals ordered in error carry a 20% restocking fee (return policy).