New Holland 2355, 2358 Disc Header Service Manual
228 pages · Publication 87032364
Added to your cart. View cart
- Models
- 2355, 2358
- Manual type
- Service Manual
- Pages
- 228
- Publication
- 87032364
- Condition
- Brand new
What's inside
From the manual's own table of contents: 20 sections, 136 entries. See sample pages (PDF, 511 KB)
SECTION 00 - GENERAL INFORMATION - CHAPTER 119 topics
- Forward
- Introduction
- Product Identification Number (PIN)
- Jack Assembly
- Shielding
- Installation
- Removal
- Electrical Connections (HW340)
- Hydraulic Connections (HW340)
- Lights
- Storing the Header
- Electrical Connections (HW345, HW365)
- Hydraulic Connections (HW345, HW365)
- Specifications
- Disc Auger Header
- Hardware Torque Values
- Recommended Sealants
- Ecology and the Environment
- Universal Symbols
SECTION 00 - GENERAL INFORMATION - CHAPTER 222 topics
- Swathing
- Auger Height
- Auger Paddles
- Header Floor Pan
- Conditioner Roll Gap -- Rubber Rolls
- Conditioner Roll Gap/Roll Engagement -- Steel Parallel Slats
- Conditioner Roll Pressure
- Windrow Shields
- Conditioner Rolls
- Unplugging the Conditioner Rolls
- Roll Timing -- Rubber Rolls
- Adjust Timing
- Roll Timing -- Steel Parallel Slats
- Reset Timing
- Conditioner Belt
- Adjust Belt Tension
- Header Flotation
- Adjustment Procedure
- Cutting Height
- Tilt Adjustment
- Header Speed Sensor
- Adjustments
SECTION 00 - GENERAL INFORMATION - CHAPTER 320 topics
- Overview
- Lubrication
- General Information
- Grease Fittings
- Gearboxes
- Miscellaneous
- Lubrication and Service Schedule
- Lubricated Components
- Auger Drive Chain
- Cutter Bar Driveshafts
- Header Drive Idler Pivot
- Auger Drive Idler Pivots
- Conditioner Driveshafts
- Conditioner Roll Driveshafts
- Upper Conditioner Roll Arm Pivots
- Conditioner Roll Pressure Crank
- Header Drive Gearbox
- Cutter Bar Modules
- Conditioner Drive Gearbox
- Cutter Bar Pivot Points
SECTION 35 - HYDRAULICS - CHAPTER 112 topics
- Description of Operation
- Hydraulic Motors
- Left Side Motor and Coupling
- Right Side Motor
- Field Overhaul
- Motor
- Coupling
- Disassembly
- Left Side Motor Coupling Housing
- Assembly
- Hydraulic Hoses and Fittings
- Labor Guide
SECTION 35 - HYDRAULICS - CHAPTER 25 topics
- Special Tools
- Fixed Displacement Motor
- Overhaul
- Hydraulic Motor
- Inspection
SECTION 35 - HYDRAULICS - CHAPTER 34 topics
- Fixed Displacement Motors
- Back Plate
- Main Shaft
- Troubleshooting
SECTION 58 - ATTACHMENTS/HEADERS - CHAPTER 14 topics
- Bevel Gearbox
- Upper Bearing
- Side Shaft
- Gearbox
SECTION 58 - ATTACHMENTS/HEADERS - CHAPTER 26 topics
- Cutter Bar
- Cutter Bar Analysis
- Inspection/Failure
- Top Cap
- Cutter Bar Bayonet Bushing
- Disc Module
SECTION 58 - ATTACHMENTS/HEADERS - CHAPTER 32 topics
- Cutter Bar Driveshaft
- Reassembly
SECTION 58 - ATTACHMENTS/HEADERS - CHAPTER 41 topic
- Auger and Auger Drive
SECTION 58 - ATTACHMENTS/HEADERS - CHAPTER 61 topic
- Conditioner Roll Drive Shaft
SECTION 58 - ATTACHMENTS/HEADERS - CHAPTER 76 topics
- Conditioner Assembly HW340/2355
- Lower Rubber or Steel Conditioner Roll 2355/2358
- Upper Rubber or Steel Conditioner Roll 2355/2358
- Rubber Conditioning Rolls
- Steel Parallel Slats
- Timing and Gap for Steel
SECTION 58 - ATTACHMENTS/HEADERS - CHAPTER 83 topics
- Conditioner Roll Tension System
- Right Side Torsion Arm and Bar
- Left Side Torsion Arm and Bar
SECTION 88 - OPTIONAL EQUIPMENT - CHAPTER 19 topics
- Optional Equipment
- Field Installed Options
- High Stubble Kit
- Header Closure Kit
- Steel Slatted Conditioning Rolls
- Gauge Wheel Kit
- Rolling Crop Dividers
- Push Bar and Dividers
- Replacement Disc Knives
SECTION 00 - GENERAL INFORMATION1 topic
- Charts
SECTION 88 - OPTIONAL EQUIPMENT1 topic
- Safety Decals
Inside this manual
Real pages from this service manual (228 pages). Open the sample pages (PDF, 511 KB)
- Specifications, page 45: SECTION 00 - GENERAL INFORMATION - CHAPTER 3
- Repair procedure, page 120: SECTION 58 - ATTACHMENTS/HEADERS - CHAPTER 2
- Diagram, page 186: SECTION 58 - ATTACHMENTS/HEADERS - CHAPTER 7
This is a service manual
Here's how it compares to the other manual types.
Service manual
Factory repair procedures and technical information such as specifications, troubleshooting, and wiring and hydraulic diagrams, for the models and systems the manual covers. See What's inside for its topics.
Operator's manual
Safe operation, controls, maintenance schedules, lubrication points, inspections, and basic checks. Repair procedures are in the service manual.
Parts manual
Illustrated diagrams with factory part numbers for identifying components and ordering parts. Repair procedures are in the service manual.
Engine service manuals are sometimes sold separately, since certain machine models were offered with more than one engine option.
What it's used for
Factory manual for in-house farm and construction shop use. Straightforward, complete, and easy to follow. It contains the OEM information dealership service departments and parts counters use to diagnose problems, identify components, and perform maintenance or repairs correctly.
Service shops and owner/operators who repair their own equipment
Identifying correct parts and seeing how assemblies come apart and go back together
Keeping equipment running with less downtime
Factory manual, 228 pages
Quantity one is the manual described above.
Fast free USA shipping
Ships in 1 business day.
60-day returns
Free if the mistake is ours. A manual ordered in error must come back unopened in its shrink-wrap; you pay return shipping and a 20% restocking fee applies. Return policy
Questions about model, serial number, engine coverage or contents? Contact us before purchasing and we'll help confirm it's the right manual. Please verify the manual type, machine model, serial number range and engine coverage before purchasing: manuals ordered in error carry a 20% restocking fee (return policy).