New Holland 346W, 356W, 366W Windrow Forage Header Service Manual
144 pages · Publication 87576103
Added to your cart. View cart
- Models
- 346W, 356W, 366W Windrow
- Manual type
- Service Manual
- Pages
- 144
- Publication
- 87576103
- Condition
- Brand new
What's inside
From the manual's own table of contents: 42 sections, 105 entries. See sample pages (PDF, 497 KB)
Specifications3 topics
- Removal
- Shaft Replacement
- Installation
Drive Gearbox2 topics
- Disassembly
- Assembly
Header Mounting Frame3 topics
- Inspection – Upper Slide Plate and Friction Pads
- Inspection – Lower Slide Plate and Friction Pad
- Slide Friction Pad -- Adjustment and/or Replacement
Auger Drive Chain4 topics
- Removal (Pre-Upgrade of Auger Support Arm)
- Installation (Pre-Upgrade of Auger Support Arm)
- Removal (Upgraded Auger Support Arm)
- Installation (Upgraded Auger Support Arm)
Wind Guard4 topics
- Finger Replacement
- Adjustment
- Wind Guard Hydraulic Lift Disconnect (If Equipped)
- Wind Guard Hydraulic Lift Connect (If Equipped)
Skid Shoes4 topics
- Removal (Outer Skid Shoe -- Right-hand Side)
- Installation (Outer Skid Shoe -- Right-hand Side)
- Removal (Inner Skid Shoe)
- Installation (Inner Skid Shoe)
Tine Bar and Tine Bar Bearing1 topic
- 366W Right-hand Side Pickup Reel
Cam Bearing1 topic
- Right Side -- Removal (356W and 366W units)
Pickup Reel Cam4 topics
- Right Side – Removal (356W and 366W units)
- Right Side – Installation
- Left Side – Removal
- Left Side – Installation
Show all 42 sections
Right Reel Bearings and Hex Shaft2 topics
- Right Reel Bearing Removal
- Right Reel Bearing and Hex Shaft Installation
Pickup Reel/Reel Tube1 topic
- Removal Overview
366W Reel Tube Center1 topic
- Installation Overview
Pickup Install Left-hand Side1 topic
- All Models
Auger Jackshaft Bearings3 topics
- Inboard Bearing Replacement
- Outboard Bearing Removal and Disassembly
- Outboard Bearing Replacement – Assembly and Installation
Auger Hold-down Springs4 topics
- Compression Release – Early Model Configuration
- Springs – Early Model Configuration
- Compression Release – Late Model or Upgrade Configuration
- Upgrade Configuration
Auger End Bearings Replacement5 topics
- Left-End Bearing -- Removal
- Left-End Bearing -- Installation
- Right-End Bearing – Removal
- Procedure 1
- Procedure 2
Auger Center Bearing – Replacement6 topics
- Auger Center Cover -- Removal
- Left-Center Bearing – Removal
- Left-Center Bearing – Installation
- Right-Center Bearing – Removal
- Right-Center Bearing – Installation
- Auger Center Cover – Installation
Auger Finger and Finger Holder and Shaft Replacement1 topic
- Finger Holder/Finger Holder Shaft Replacement
Auger Finger Guide Replacement1 topic
- Retractable Finger Shaft -- Added Strength
Auger Strippers2 topics
- Auger Strippers -- Short Left-Hand
- Auger Stripper Adjustment
Pickup Slip Clutch7 topics
- Slip Clutch Removal
- Slip Clutch Disassembly
- Slip Clutch Components Inspection
- Slip Clutch Assembly
- Slip Clutch Installation
- Slip Clutch Adjustment and Settings
- Run-in Procedure -- For New Clutch or Friction Discs
Auger Radial Pin Slip Clutch3 topics
- Removal and Exterior Inspection
- Torque Inspection
- Component Inspection
Inside this manual
Real pages from this service manual (144 pages). Open the sample pages (PDF, 496 KB)
- Specifications, page 18: SECTION 00 -- GENERAL INFORMATION -- CHAPTER 2
- Diagram, page 58: Removal
- Repair procedure, page 84: PICKUP REEL/REEL TUBE
This is a service manual
Here's how it compares to the other manual types.
Service manual
Factory repair procedures and technical information such as specifications, troubleshooting, and wiring and hydraulic diagrams, for the models and systems the manual covers. See What's inside for its topics.
Operator's manual
Safe operation, controls, maintenance schedules, lubrication points, inspections, and basic checks. Repair procedures are in the service manual.
Parts manual
Illustrated diagrams with factory part numbers for identifying components and ordering parts. Repair procedures are in the service manual.
Engine service manuals are sometimes sold separately, since certain machine models were offered with more than one engine option.
What it's used for
Factory manual for in-house farm and construction shop use. Straightforward, complete, and easy to follow. It contains the OEM information dealership service departments and parts counters use to diagnose problems, identify components, and perform maintenance or repairs correctly.
Service shops and owner/operators who repair their own equipment
Identifying correct parts and seeing how assemblies come apart and go back together
Keeping equipment running with less downtime
Factory manual, 144 pages
Quantity one is the manual described above.
Fast free USA shipping
Ships in 1 business day.
60-day returns
Free if the mistake is ours. A manual ordered in error must come back unopened in its shrink-wrap; you pay return shipping and a 20% restocking fee applies. Return policy
Questions about model, serial number, engine coverage or contents? Contact us before purchasing and we'll help confirm it's the right manual. Please verify the manual type, machine model, serial number range and engine coverage before purchasing: manuals ordered in error carry a 20% restocking fee (return policy).