New Holland 565, 570, 575, 580 Square Baler Service Manual
539 pages · Publication 86641879
Added to your cart. View cart
What's inside
From the manual's own table of contents: 81 sections, 184 entries. See sample pages (PDF, 487 KB)
Technical Information4 topics
- Hardware
- Tightening Torques
- Retaining, Locking and Sealing Compounds
- Standard Torque Data for Hydraulic Tubes and Fittings
31 201 Universal Joint and Power Pivot1 topic
- Description and Operation
Baler Slip and Overrunning Clutch3 topics
- Operation
- Checking a Slip Clutch
- Slip Clutch Adjustment
Rear Universal Joint and Overrunning Clutch2 topics
- Model 565 with Standard PTO Slip Clutch
- Model 565 with Heavy Duty Slip Clutch and Models 570, 575, and 580
PTO Shaft Shields1 topic
- Model 565
Joint Replacement1 topic
- Quick Detachable Yoke
Show all 81 sections
68 000 General Information3 topics
- Standard vs. Heavy Duty Knotters
- Bale and Knot Formation
- Knotter Trip System Operation
Knotter Adjustments14 topics
- Standard and Heavy Duty Knotters
- Raising the Knotter Frame
- Billhook Cam Spring
- Knife Arm
- Twine Disc and Holder
- Needle Adjustments
- Twine Fingers
- Knotter Brake
- Twine Guides
- Twine Tension Plates
- Knotter Timing
- Checking or Adjusting the Timing
- Needle Safety Latch
- Knotter Trip Stop and Reset Adjustments
Knotter Frame Assembly Components13 topics
- Knife Arm and Cam Gear Identification - Bulletin 12/95 H9
- Knife Arm Knife
- Knife Arm Roller
- Billhook Pinion Gear
- Billhook
- Billhook Tongue and Roller
- Billhook Cam and Spring
- Twine Holder Spring
- Twine Holder
- Twine Disc and Cleaners
- Worm Shaft and Gears
- Knotter Frame
- Billhook Roller Cam
Knotter Frame Assembly12 topics
- Standard Knotter
- Heavy Duty Knotter
- Needle Drive Arm
- Knotter Brake Pads
- Knotter Brake Disc
- Cam Gear
- Twine Finger Cam
- Knotter Clutch and Drive Gear
- Adding Timing Marks to the Knotter Clutch
- Knotter Clutch Drive Block
- Knotter Shaft Bearings
- Knotter Shaft
Knotter Stack Assembly3 topics
- Removing the Knotter Stack
- Installing the Knotter Stack
- Rebuilding the Knotter Stack
Knotter Related Components10 topics
- Hay Dogs
- Twine Finger Lever
- Needles
- Needle Yoke
- Needle Yoke Drive Rod
- Trip and Drive Disc
- Metering Wheel Shaft and Supports
- Knotter Stop
- Trip Lever and Pivot Shaft
- Twine Box Tension Plates
Troubleshooting3 topics
- Standard vs. Heavy Duty Twisters
- Bale and Twist Formation
- Twister Trip System Operation
Twister Adjustments15 topics
- Checking or Adjusting the Twister Timing
- Twister Frame Height
- Wire Guide and Roller
- Twister Hook Height
- Twister Hook Timing
- Twister Hook Drive Chain
- Wire Guide
- Twist Wrapper
- Shuttle Shaft to Follower Clearance
- Bevel Gear Pinion Wear Plate
- Shear Clamp Pivot Bolt
- Shear Plate and Clamp
- Clamp Pressure
- Twister Brake
- Twister Stop
Twister Frame Assembly Components5 topics
- Twist Wrapper and Wire Guides
- Twister Hook and Shaft Assembly
- Shuttle Shaft Assembly
- Shuttle Bar
- Shear Plate, Clamp Stack and Shear Clamp
Twister Frame Assembly7 topics
- Twister Brake Pads
- Twister Brake Disc
- Pinion Support
- Twister Clutch and Drive Gear
- Twister Clutch Drive Block
- Twister Shaft Bearings
- Twister Shaft
Twister Stack Assembly2 topics
- and 580 Baler
- and 570 Baler
Twister Related Components4 topics
- Unloading Roller
- Needle Roller Replacement
- Trip Arm and Drive Disc
- Bale Counter
Inside this manual
Real pages from this service manual (539 pages). Open the sample pages (PDF, 486 KB)
- Specifications, page 56: SECTION 31 - IMPLEMENT DRIVELINE - CHAPTER 1
- Troubleshooting, page 392: PROBLEM
Other manuals for this machine
Save 10% on 2 manuals, 15% on 3 or more. Other manuals are listed below. Editions cover different serial number ranges: check the serial coverage and tick only the ones that match your machine.
Added to your cart. View cart
This is a service manual
Here's how it compares to the other manual types.
Service manual
Factory repair procedures and technical information such as specifications, troubleshooting, and wiring and hydraulic diagrams, for the models and systems the manual covers. See What's inside for its topics.
Operator's manual
Safe operation, controls, maintenance schedules, lubrication points, inspections, and basic checks. Repair procedures are in the service manual.
Parts manual
Illustrated diagrams with factory part numbers for identifying components and ordering parts. Repair procedures are in the service manual.
Engine service manuals are sometimes sold separately, since certain machine models were offered with more than one engine option.
What it's used for
Factory manual for in-house farm and construction shop use. Straightforward, complete, and easy to follow. It contains the OEM information dealership service departments and parts counters use to diagnose problems, identify components, and perform maintenance or repairs correctly.
Service shops and owner/operators who repair their own equipment
Identifying correct parts and seeing how assemblies come apart and go back together
Keeping equipment running with less downtime
Factory manual, 539 pages
Quantity one is the manual described above.
Fast free USA shipping
Ships in 1 business day.
60-day returns
Free if the mistake is ours. A manual ordered in error must come back unopened in its shrink-wrap; you pay return shipping and a 20% restocking fee applies. Return policy
Binder not included
Manuals over about 300 pages may need a standard 3-ring binder, which you can buy locally to keep the pages organized for shop use.
Questions about model, serial number, engine coverage or contents? Contact us before purchasing and we'll help confirm it's the right manual. Please verify the manual type, machine model, serial number range and engine coverage before purchasing: manuals ordered in error carry a 20% restocking fee (return policy).