New Holland BB9050, BB9060, BB9070, BB9080 Square Baler Operator's Manual
372 pages · Publication 87474948
Fast free USA shippingShips in 1 business daySave 10% on 2 manuals, 15% on 3 or morePay by credit or debit card or with PayPal. No PayPal account needed.
Added to your cart. View cart
- Models
- BB9050, BB9060, BB9070, BB9080
- Manual type
- Operator's Manual
- Pages
- 372
- Publication
- 87474948
- Condition
- Brand new
What's inside
From the manual's own table of contents: 210 sections, 421 entries. See sample pages (PDF, 784 KB)
Intended use
Product identification
Airborne noise emission
Electromagnetic compatibility (EMC)
EC Certificate of conformity
Vibration level information
Legal obligations1 topic
- Safety requirements for fluid power systems and components
Precautionary statements2 topics
- Personal safety
- Machine safety
Safety precautions9 topics
- Farm accidents can be prevented with your help
- General recommendations
- Electrical power lines
- Danger of death by electrocution!
- Operating the baler
- Transporting the baler
- Field operation
- Machine maintenance
- CropCutter t
Wheels and tyres
Angle of operation
Safety decals2 topics
- European units only
- North America units only
Needles/knotter safety lock
Access to machine components4 topics
- Safety guards
- Easy lock (N/America only)
- Flywheel access door
- Bale chamber inspection door
Protective devices2 topics
- Width signal plates
- Wheel chock
Parkbrake
Toolboxes2 topics
- Small
- Large
Lifting the baler
Baler overview4 topics
- Front view
- Right hand view
- Left hand view
- Rear end view
Controls, indicators and gauges
Flywheel brake
Jack
Tractor requirements
Horsepower requirements
Show all 210 sections
Tractor drawbar / tow hitch
Tractor wheel setting
PTO shaft
Baler to tractor attachment4 topics
- Tractor drawbar with PIN
- Pin hitch type
- Tractor drawbar with fixed ball hitch
- Attachment of the hitch
PTO shaft phasing
Baler levelling2 topics
- Position of the mid--ship bearing
- PTO Driveline configuration
Hitch Adjustable low (standard)
Hitch adjustable high low for standard or packer--cutter units1 topic
- General
Hitch adjustable high/low for standard or packer--cutter units (high position)
Hitch adjustable high/low for BB9050 and BB9060 rotor--cutter units (low position shown)
Hitch adjustable high/low for BB9070 and BB9080 rotor--cutter units (high position shown)
PTO shaft attachment
Safety chain / safety cable (not for France)
Braking systems fail safe brake control (France only)
Tractor hydraulic brake connections (where fitted*)
Tractor pneumatic brake connections (where fitted*)
Tractor hydraulic connections
Tractor electrical system2 topics
- Road lights: except North America
- Road lights: North America only
Baler electrical system6 topics
- Road lights
- Side lights (if fitted)
- Working light (optional)
- Revolving flashlight (where fitted and subject to local legislation)
- Electric accessories output
- V DC sockets
Monitor installation1 topic
- Monitors
Monitor Introduction3 topics
- Layered architecture
- Foundation
- Download symbols
Monitor options
InfoView t II (black and white display) -- optional equipment
Controls selection
Intelliviewt III (touchscreen colour display) -- Optional equipment3 topics
- Main screen area (Tractor example)
- Icon Description
- Main screen area (Baler example)
InfoView t II13 topics
- Soft key keypad
- Navigation keypad
- Keypad inputs
- Keypad access
- Keypad selections
- Touch screen selections
- Special keys
- Input error messages
- Pop--up lists
- Languages available
- Screen options
- Switching applications InfoView t II
- Switching applications IntelliView t III
Monitor toolbox application (Display set--up)12 topics
- Display Set--up screen
- Language
- Operator set--up screen
- Creating an operator (if applicable)
- Video Camera (IntelliView t III only)
- Layout creation
- Changing layouts
- Choosing modules
- Implement
- Monitor VT preferences
- Monitor preferences
- Distance
Monitor auxiliary controls screen6 topics
- RAM and NVM browser screens
- About screen
- Monitor run application
- Diagnostics application
- Run screen
- Data management screen
InfoView t II (black and white display) Optional equipment
IntelliView t III (colour touchscreen) Optional equipment
Screen menus2 topics
- Main Screen menu bar (Screen selection icons)
- Main screen menu bar (Direct access icons)
Screen options1 topic
- Screen functions
Main screen < 600 rpm
Main screen > 600 rpm2 topics
- Load indicator
- Capacity indicator
Field settings
Memory1 topic
- Bale weight (where fitted)
Service1 topic
- Confirmation of a service interval
User settings
Screen set--up
Active errors2 topics
- Error overview
- Error codes
Lights setting
Machine settings1 topic
- User configurable items
Information
Diagnosis Input
Diagnosis Output
Screen status area
Displayed monitor messages4 topics
- Operational messages
- Warning messages
- Alarm messages
- Error messages
Operational messages
Warning messages (Yellow)
Stop (alarm) messages (Red)1 topic
- Pick--up cut out Auto Stop function (where fitted on Rotor--Cutter balers only)
Error messages (Orange)
Pick--up compensation cylinder1 topic
- Transport setting
Transporting the baler
Parking the baler
Description of operation
Product feeding
Pick-up9 topics
- Pick-up gauge wheel settings
- Pick up cylinder components
- Pick-up lift control
- Pick up cylinder height setting
- Setting process for downforce
- Pick up force
- Pick--up centering augers
- Pick-up baffle plate
- Roller windguard (where fitted)
CropCutter t controls
Packer units
Packer--Cutter units5 topics
- Purpose
- Operation
- Knife operation
- Knife removal/installation
- False knifes
Rotor--Cutter units4 topics
- CropCutter t hydraulic circuit
- False (blank) knives
- Cutting length -- CropCutter t
- Knife drawer options
Unplugging the Rotor--Cutter system
Pre-compression chamber
Stuffer trip lock (where fitted)
Stuffer trip sensitivity lever
Stuffer
Charge holding fingers
Pressing
Plunger/bale chamber
Hay dogs
Bale density system
General2 topics
- Location of components
- Serpentine cooler
Automatic bale density control1 topic
- Density valve
Manual bale density control
Manual override bale density control
Tying
Knotter / needle drive components
Threading the baler17 topics
- Twine routing components
- Twine balls and usage
- knotter left hand side
- knotter right hand side
- knotter left hand side
- knotter right hand side
- Twine Threading
- Flywheel brake
- Accessing top of baler
- Kneedle knotter lock
- Twine routing
- Twine routing to the knotters
- Fan shielding
- Knotter guard
- Twine connecting knotter to needles
- Twine routing to needles
- Twine type
Bale length mechanical control1 topic
- Mechanical bale counter
Bale length electronic trip (where fitted)
Knotters
Monitoring flags2 topics
- Monitoring flag(s) stay down
- Monitoring flag(s) stay up
Missed knots
Roller bale chute2 topics
- Bale chute unfolding
- Folded position
Bale Eject t system3 topics
- Bale release lock--out valve
- Bale Eject t -- standard
- Partial bale eject system (where fitted is in addition to the standard Bale Eject t )
Tandem AutoSteer t axle (if fitted)
Operation3 topics
- How to lock the rear wheels
- How to unlock the rear wheels
- Usage
AutoSteer t lock-out valve
Shearbolts3 topics
- Flywheel
- Knotter drive
- Stuffer
Baling2 topics
- Preparing the crop for baling
- Straw crops
Windrow/swath size1 topic
- Over-sized windrows wider than 140 cm (55 in)
Baling considerations8 topics
- Knives
- Prior to field work
- Empty bale chamber
- Baler speed
- Performance checks
- Bale weight
- Bale shape
- Bale size
Bale conservation1 topic
- Moisture setting
Bale weight (where fitted)
Camera (where fitted)
Baling check--list I
Baling check--list II
Lubrication
General information
Lubrication and maintenance quick reference
Centralized greasing system
Automatic greasing system (if installed)3 topics
- Grease specification
- Grease reservoir filling
- Quick fill kit
Remaining conventional grease points
PTO drive line greasing1 topic
- Grease quantity
Automatic oiling system3 topics
- Automatic oiling reservoir components
- Venting the oil pump
- Oil specification
Linkages, threaded rods and pivots
Ball ring hitch and wear plate
Main drive gearbox3 topics
- Oil level
- Oil change
- Gearbox capacity
Stuffer drive gearbox
Knotter drive gearbox
Bale density hydraulic circuit3 topics
- Oil drain
- Oil filter change
- Air filter change
Chains
Packer/rotor drive chain
Pick--up main drive chain and pick--up reel drive chain
Pick--up auger drive chain
Main drive
PTO drive slip clutch2 topics
- All models
- Burnishing the slip clutch
Pick--up slip clutch
Pick-up tine replacement2 topics
- Standard and Packer--Cutter units only (steel sprung tines)
- Rotor--Cutter units (rubber mounted tines)
Auger stripper plates
Packer slip clutch
Rotor cut-out clutch
Knife drawer adjustments1 topic
- Centering the crop cutting knives in the rotor blades
Cutter knife sharpening2 topics
- Standard knives only
- Stuffer trip mechanism
Stuffer brake
Stuffer fingers to plunger timing
Crop holding fingers
Stuffer adjustment1 topic
- Plunger rollers
Twine tying mechanism1 topic
- Twine breakage
Twine tension
Description of the knotter assembly
Knotter adjustments5 topics
- Knotter bill hook and cam adjustment
- Stripper arm knife replacement
- Stripper arm adjustment
- Twine disc adjustment
- Twine holder
Knotter trip mechanism2 topics
- Knotter trip mechanism in the home position
- Resetting the knotter trip mechanism
Needle adjustment2 topics
- Needle to bale chamber adjustment
- Needle to twine disc adjustment
Maximum needle penetration
Needles to plunger timing / knotter drive shearbolt replacement1 topic
- Knotter drive shearbolt replacement
Tucker arm alignment
Needle carriage support
Needle brake1 topic
- Brake adjustment with baler in rotation
Needle protection linkage
Twine fingers
Electrical system1 topic
- Fuses and relays
System override2 topics
- If the main power relays are still powered
- If the main power relays are not powered
Power distribution2 topics
- Avoiding electrical problems
- Sensors (digital)
Lights-bulb replacement6 topics
- Front road lights
- Side lights
- Rear road lights
- License plate light
- Working light
- Revolving flashlight
Hydraulic system3 topics
- Hydraulic hose replacement
- Tyre pressure
- Wheel nuts torque
Brake system (Where fitted)2 topics
- Brake drum linings
- Brake adjustment
Hydraulic brake system (Where fitted)2 topics
- Bleeding the brake control cylinder(s)
- Fail safe brake control (France only)
Air brake system (if fitted)1 topic
- Air reservoir specification
Cleaning the baler
Drives
Bale shape
Integrated automatic oiler
Bale density regulation
Packer--cutter system
Rotor--cutter system
End-of-season service
Ordering parts and/or accessories
Pre--season service
Tractor drawbar swivel ball kit
Tractor drawbar fixed ball hitch kit
Revolving flashlight
Working lights
Extra working lights
Needle and knotter light
Pickup light kit
Automatic greasing pump
Quick fill pump
Partial Bale--Eject t system
Fill flow kit
Pick up stop (Rotor--Cutter only)
Moisture sensor system
Bale length trip (electronic)
VT cable kit
Roller windguard
Knife drawer frame
Bale weighing system
Monitors
Camera kit
Needle cleaning kit
Signal plates (France and Germany)
Pneumatic brake connector (Italy)
Side light kit (Denmark)
Bale accumulator
Check and adjust, as required (Dealer copy)
Check and adjust, as required (Customer copy)
Inside this manual
Real pages from this operator's manual (372 pages). Open the sample pages (PDF, 783 KB)
- Controls and operation, page 67: BRAKING SYSTEMS FAIL SAFE BRAKE
- Maintenance, page 242: SECTION 4 -- LUBRICATION AND MAINTENANCE
- Specifications, page 357: SECTION 8 -- SPECIFICATIONS
- Color page, page 143: SECTION 2 -- CONTROLS, INSTRUMENTS AND OPERATION
- Color page, page 203: SECTION 3 -- FIELD AND SITE OPERATION
This is an operator's manual
Here's how it compares to the other manual types.
Service manual
Factory repair procedures and technical information such as specifications, troubleshooting, and wiring and hydraulic diagrams, for the models and systems the manual covers. See What's inside for its topics.
This manual
Operator's manual
Safe operation, controls, maintenance schedules, lubrication points, inspections, and basic checks. Repair procedures are in the service manual.
Parts manual
Illustrated diagrams with factory part numbers for identifying components and ordering parts. Repair procedures are in the service manual.
What it's used for
Factory manual for in-house farm and construction shop use. Straightforward, complete, and easy to follow. It contains the OEM information dealership service departments and parts counters use to diagnose problems, identify components, and perform maintenance or repairs correctly.
Service shops and owner/operators who repair their own equipment
Identifying correct parts and seeing how assemblies come apart and go back together
Keeping equipment running with less downtime
Factory manual, 372 pages
Quantity one is the manual described above.
Fast free USA shipping
Ships in 1 business day.
60-day returns
Free if the mistake is ours. A manual ordered in error must come back unopened in its shrink-wrap; you pay return shipping and a 20% restocking fee applies. Return policy
Binder not included
Manuals over about 300 pages may need a standard 3-ring binder, which you can buy locally to keep the pages organized for shop use.
Questions about model, serial number, engine coverage or contents? Contact us before purchasing and we'll help confirm it's the right manual. Please verify the manual type, machine model, serial number range and engine coverage before purchasing: manuals ordered in error carry a 20% restocking fee (return policy).