New Holland BR730A Round Baler Service Manual
196 pages · Publication 87364832
Added to your cart. View cart
- Models
- BR730A
- Manual type
- Service Manual
- Pages
- 196
- Publication
- 87364832
- Condition
- Brand new
What's inside
From the manual's own table of contents: 23 sections, 98 entries. See sample pages (PDF, 516 KB)
Fluid Safety4 topics
- Handle Fluids Safely
- Avoid Heating Near Pressurized Fluid Lines
- Use Care Around High-pressure Fluid Lines
- Safe Service Procedures
Technical Information1 topic
- Hardware
Minimum Hardware Tightening Torques3 topics
- Thread Locking Compounds
- Retaining Compounds
- Sealants
Lubrication1 topic
- Roller Chains
International Symbols1 topic
- Baler Components
Specifications1 topic
- PTO Constant Velocity
Overhaul11 topics
- Front PTO and CV U-joint
- Disassembly
- Inspection
- Assembly
- Installation
- Rear PTO
- Removal
- Shear Bolt Hub
- Shear Bolt Hub Bearing Balls
- Replace
- Slide Collar Quick-Disconnect
Description of Operation1 topic
- Gearbox
General Procedures1 topic
- Lift Cylinder
Definition of Terms12 topics
- Electricity
- Voltage
- Current
- Resistance
- Open Circuit
- Short Circuit
- Continuity
- Voltage Drop
- Diode
- Solenoid
- Relay
- During Charging or Welding
Special Tools5 topics
- Test Procedure 1: Continuity Test for Open Circuits
- Test Procedure 2: Continuity Test for Short to Ground
- Test Procedure 3: Resistance Test for Electrical Components
- Test Procedure 4: Voltage Measurement
- Electrical Control Box
Adjustment8 topics
- Full Bale Alarm Switch
- Wire Harness Connector
- 9-Pin Connector
- Round Connector
- Gray Rectangular Connector
- Light Plug
- 3-Pin Plug
- Light Module
Baler Lights Wiring Diagram5 topics
- Finger
- Cam Bearing
- Slip Clutch
- Pickup
- Cam Track
Sectional Views15 topics
- Floor Roll
- Starter Roll
- Belt Tension
- Drive Roll
- Adjustment
- Idler Rolls
- Roll 21
- Inspection (All Idler Rolls)
- Take-Up Arm
- Belt Failure Analysis
- Belt Tension Removal
- Laced Belt
- Belt Tracking
- Follower Roll
- Pivot Roll Sledge Assembly
Adjustments6 topics
- Drive Chains
- Wrapper Arm
- Twine Knife
- Drive Motor
- Twine Arm Drive
- Repair
Inside this manual
Real pages from this service manual (196 pages). Open the sample pages (PDF, 515 KB)
- Troubleshooting, page 97: SECTION 55 - ELECTRICAL SYSTEMS - CHAPTER 1
- Diagram, page 106: SECTION 55 - ELECTRICAL SYSTEMS - CHAPTER 3
- Specifications, page 118: SECTION 60 - PRODUCT FEEDING - CHAPTER 1
Other manuals for this machine
Save 10% on 2 manuals, 15% on 3 or more. Other manuals for the BR730A are listed below. Editions cover different serial number ranges: check the serial coverage and tick only the ones that match your machine.
Added to your cart. View cart
This is a service manual
Here's how it compares to the other manual types.
Service manual
Factory repair procedures and technical information such as specifications, troubleshooting, and wiring and hydraulic diagrams, for the models and systems the manual covers. See What's inside for its topics.
Operator's manual
Safe operation, controls, maintenance schedules, lubrication points, inspections, and basic checks. Repair procedures are in the service manual.
Parts manual
Illustrated diagrams with factory part numbers for identifying components and ordering parts. Repair procedures are in the service manual.
Engine service manuals are sometimes sold separately, since certain machine models were offered with more than one engine option.
What it's used for
Factory manual for in-house farm and construction shop use. Straightforward, complete, and easy to follow. It contains the OEM information dealership service departments and parts counters use to diagnose problems, identify components, and perform maintenance or repairs correctly.
Service shops and owner/operators who repair their own equipment
Identifying correct parts and seeing how assemblies come apart and go back together
Keeping equipment running with less downtime
Factory manual, 196 pages
Quantity one is the manual described above.
Fast free USA shipping
Ships in 1 business day.
60-day returns
Free if the mistake is ours. A manual ordered in error must come back unopened in its shrink-wrap; you pay return shipping and a 20% restocking fee applies. Return policy
Questions about model, serial number, engine coverage or contents? Contact us before purchasing and we'll help confirm it's the right manual. Please verify the manual type, machine model, serial number range and engine coverage before purchasing: manuals ordered in error carry a 20% restocking fee (return policy).