MidWestTechService, Parts and Operator's Manuals, in stock and ready to ship!
Fast free USA shippingShips in 1 business daySave 10% on 2 manuals, 15% on 3+

New Holland IntelliSteer Auto Steering System TG, TJ Tractor Service Manual

95 pages · Publication 87046843

$69.73
Fast free USA shippingShips in 1 business daySave 10% on 2 manuals, 15% on 3 or morePay by credit or debit card or with PayPal. No PayPal account needed.
Models
IntelliSteer Auto Steering System TG, TJ
Manual type
Service Manual
Pages
95
Publication
87046843
Condition
Brand new
New Holland IntelliSteer Auto Steering System TG, TJ Tractor Service Manual, publication 87046843

What's inside

From the manual's own table of contents: 48 sections, 87 entries. See sample pages (PDF, 542 KB)

General39 topics
  • SYMPTOM BASED FAULTS - NO FAULT CODES
  • Omnistar HP differential signal?
  • Low number of satellites when using RTK
  • inadequate satellite coverage in their location
  • RDL cannot read CompactFlash Data Card
  • Losing Configuration Settings When the RDL is Powered Off
  • Trouble activating Omnistar VBS satellite differential subscriptions on Ag252 GPS Receiver
  • Poor accuracy, non-repeatable pass to pass performance when using RTK
  • Poor GPS accuracy or swath performance with the Ag252 receiver
  • GPS Status “Wait – D7” (7 represents current number of Satellites)
  • WAAS DGPS shifts position after a period of time from startup
  • No GPS position output from the Ag252 receiver after connecting to Ag Remote v2.xx
  • Restore Ag252 Receiver factory settings
  • Not tracking RTK corrections, Wait-A7 message (7 represents the number of satellites)
  • Long time to initialize RTK
  • (6 represents the current number of satellites)
  • Using WAAS to reduce error when setting up a RTK Base Station location
  • LED sequences for WAAS or Omnistar VBS differential positioning
  • LED sequences for Omnistar HP differential positioning
  • LED sequences for RTK positioning
  • Vehicle Confusion in Swath Orientation
  • Steering seems erratic or confused
  • Vehicle continues in Auto Mode, but drifts offline
  • Front wheel drift, hard steering, vehicle fails to come online when in autoguidance, initial installation setup
  • Solid Green LED on the Ag252 receiver, but no GPS Info on the Display – GPS Status None
  • Controller Guidance System Fault Code 1 “FE Send Message
  • Controller Guidance System Fault Code 2 “FE Task Init
  • Controller Guidance System Fault Code 3 “FE Go Trap
  • Controller Guidance System Fault Code 4 “A/D Scan Timeout
  • Controller Guidance System Fault Code 5 “A/D Scan Overrun
  • Controller Guidance System Fault Code 6 “A/D Data Not Ready
  • Controller Guidance System Fault Code 7 “A/D Chan Overrun
  • Controller Guidance System Fault Code 8 “Vpp Jumpered
  • Controller Guidance System Fault Code 9 “Battery Bad
  • Controller Guidance System Fault Code 11 “SP Open Failed
  • Controller Guidance System Fault Code 12 “Matrix Inv. Failed
  • Controller Guidance System Fault Code 13 “MATHERR Exception
  • Controller Guidance System Fault Code 14 “MATHERRF Exception
  • Controller Guidance System Fault Code 15 “Fatal Error Reboot
Controller Guidance System Fault Code 16 “App Undefined ISR
Controller Guidance System Fault Code 17 “TPU Undefined ISR
Controller Guidance System Fault Code 18 “MIOS1 Undefined ISR
Controller Guidance System Fault Code 19“QADC Undefined ISR
Controller Guidance System Fault Code 21 “Uninit. App Assert
Controller guidance System Fault Code 22 “Acc X Overvoltage
Controller Guidance System Fault Code 23 “Acc X Undervoltage
Controller Guidance System Fault Code 24 “Acc Y Overvoltage
Controller Guidance System Fault Code 25 “Acc Y Undervoltage
Controller Guidance System Fault Code 26 “Acc Z Overvoltage
Controller Guidance System Fault Code 27 “Acc Z Undervoltage
Controller Guidance System Fault Code 28 “Gyro X Overvoltage
Controller Guidance System Fault Code 29 “Gyro X Undervoltage
Controller Guidance System Fault Code 30 “Gyro Y Overvoltage
Controller Guidance System Fault Code 31 “Gyro Y Undervoltage
Controller Guidance System Fault Code 32 “Gyro Z Overvoltage
Controller Guidance System Fault Code 33 “Gyro Z Undervoltage
Controller Guidance System Fault Code 34 “Heater Overvoltage
Controller Guidance System Fault Code 35 “Heater Undervoltage
Controller Guidance System Fault Code 36 “VRef Overvoltage
Controller Guidance System Fault Code 37 “VRef Undervoltage
Controller Guidance System Fault Code 39 “Steering Overvolt
Controller Guidance System Fault Code 40 “Steering Overvolt
Show all 49 sections
Controller Guidance System Fault Code 40 “Steering Undervolt
Controller Guidance System Fault Code 41 “Man Ovrd Overvolt
Controller Guidance System Fault Code 42 “Man Ovrd Undervolt
Controller Guidance System Fault Code 43 “Gear Lev Overvolt
Controller Guidance System Fault Code 44 “Gear Lev Undervolt
Controller Guidance System Fault Code 46 “Valve Coil Short
Controller Guidance System Fault Code 47 “Valve Coil Imax
Controller Guidance System Fault Code 48 “MOSFET Short
Controller Guidance System Fault Code 49 “Coil Short to GND
Controller Guidance System Fault Code 50 “Coil Shorted
Controller Guidance System Fault Code 54 “SafeMCU Prog. Error
Controller Guidance System Fault Code 55 “SafeMCU No Stack
Controller Guidance System Fault Code 56 “SafeMCU Msg Timeout
Controller Guidance System Fault Code 58 “Angle Out of Bounds
Controller Guidance System Fault Code 58 “Steering Unsafe
Controller Guidance System Fault Code 59 “MCU2 Vel. Unsafe
Controller Guidance System Fault Code 70 “Test Build Expired
Controller Guidance System Fault Code 71 “Top FET Sense Err
Controller Guidance System Fault Code 76 “VT Assert Failure
Controller Guidance System Fault Code 77 “VT Object Pool Buffer Overflow
Controller Guidance System Fault Code 78 “VT Comms Error
Controller Guidance System Fault Code 79 “VT Watchdog Timeout
Controller Guidance System Fault Code 80 “PP Task Assert Failure
Controller Guidance System Fault Code 81 “CAN-VT Assert Failure
Controller Guidance System Fault Code 81 “CN Task Assert Failure

Inside this manual

Real pages from this service manual (95 pages). Open the sample pages (PDF, 542 KB)

Sample pages from the New Holland IntelliSteer Auto Steering System TG, TJ Tractor Service Manual: Troubleshooting
  • Troubleshooting, page 62: Controller Guidance System Fault Code 33 “Gyro Z Undervoltage”

This is a service manual

Here's how it compares to the other manual types.

This manual

Service manual

Factory repair procedures and technical information such as specifications, troubleshooting, and wiring and hydraulic diagrams, for the models and systems the manual covers. See What's inside for its topics.

Operator's manual

Safe operation, controls, maintenance schedules, lubrication points, inspections, and basic checks. Repair procedures are in the service manual.

Parts manual

Illustrated diagrams with factory part numbers for identifying components and ordering parts. Repair procedures are in the service manual.

Engine service manuals are sometimes sold separately, since certain machine models were offered with more than one engine option.

What it's used for

Factory manual for in-house farm and construction shop use. Straightforward, complete, and easy to follow. It contains the OEM information dealership service departments and parts counters use to diagnose problems, identify components, and perform maintenance or repairs correctly.

Service shops and owner/operators who repair their own equipment

Identifying correct parts and seeing how assemblies come apart and go back together

Keeping equipment running with less downtime

Factory manual, 95 pages

Quantity one is the manual described above.

Fast free USA shipping

Ships in 1 business day.

60-day returns

Free if the mistake is ours. A manual ordered in error must come back unopened in its shrink-wrap; you pay return shipping and a 20% restocking fee applies. Return policy

Questions about model, serial number, engine coverage or contents? Contact us before purchasing and we'll help confirm it's the right manual. Please verify the manual type, machine model, serial number range and engine coverage before purchasing: manuals ordered in error carry a 20% restocking fee (return policy).