New Holland LB75.B Backhoe Loader Parts Catalog
1,099 pages · Publication 6036803200
Added to your cart. View cart
- Models
- LB75.B
- Manual type
- Parts Catalog
- Pages
- 1,099
- Publication
- 6036803200
- Condition
- Brand new
What's inside
From the manual's own table of contents: 170 topics. See sample pages (PDF, 475 KB)
- MAIN
- MPARTS
- ENGINE 2/2
- ENGINE
- CYLINDER BLOCK
- OIL PUMP, PAN
- CYLINDER BLOCK - COVERS
- BREATHER - ENGINE
- CYLINDER HEAD
- CYLINDER HEAD - COVERS
- CYLINDER HEAD - VALVE MECHANISM
- MANIFOLD - INTAKE
- MANIFOLD - EXHAUST
- CRANKSHAFT
- PISTONS - CONNECTING ROD
- FLYWHEEL - ENGINE
- PULLEY - CRANKSHAFT
- DYNAMIC BALANCER, GEARS & SHAFTS
- DYNAMIC BALANCER, GEARS & SHAFTS (2830952)
- CAMSHAFT
- FUEL INJECTION PUMP
- FUEL INJECTION SYSTEM
- FUEL FILTER
- FUEL PUMP
Show all 170 topics
- TURBOCHARGER
- ENGINE, OIL
- OIL PUMP - ENGINE
- OIL FILTERS - ENGINE
- PIPING - ENGINE OIL
- OIL FILTER AND COOLER
- WATER PUMP
- COOLING SYSTEM - ENGINE
- THERMOSTAT - ENGINE COOLING SYSTEM
- WATER PUMP - CONTROL
- FAN DRIVE
- POWER TAKE-OFF
- STARTER MOTOR
- ALTERNATOR
- FRAME (CENTER PIVOT)
- AIR INTAKE CAP & PRE-CLEANER
- FRONT WEIGHTS
- RADIATOR
- POWER STEERING HYDRAULIC SYSTEM
- 4WD FRONT AXLE, HOUSING, BUSHINGS & SUPPORTS
- 4WD FRONT AXLE, SWIVEL HOUSING & STEERING CYLINDER
- 4WD FRONT AXLE, HUBS
- 4WD FRONT AXLE, RING GEAR & PINION ASSEMBLY
- 4WD FRONT AXLE, DIFFERENTIAL
- 4WD FRONT AXLE, DRIVE SHAFT
- FRONT AXLE - (4WD) W/GEAR,BEVEL
- ENGINE HARNESS (POWER SHUTTLE)
- SINGLE BATTERY
- DOUBLE BATTERY
- COLD START
- BUCKET, SWING, & BOOM VALVE SECTION (CENTER PIVOT)
- TWO-SECTION CONTROL VALVE FOR LOADER
- SECTION PILOT CONTROL VALVE SUPPORT,COMPLETE (CENTER PIVOT) EUROPE
- 7-SECTIONS EXCAVATOR CONTROL VALVE
- PIVOT)
- LOCK VALVE ON LOADER TILTING CYLINDERS
- LOCK VALVE ON LOADER LIFT CYLINDERS
- VALVE (CENTER PIVOT)
- VALVES (CENTER PIVOT)
- LOADER CONTROL VALVE, 4X1& 6X1 BUCKET SECTION
- STABILIZER CONTROL VALVE, THIRD SECTION, HED (CENTER PIVOT)
- LOCK VALVE FOR BUCKET 4X1 / 6X1
- LOCKING VALVE ON BACKHOE LIFT AND DIPP. CYLINDER
- BACKHOE LIFT & DIPPERSTICK CYLINDER LOCK VALVE
- ON/OFF SWITCH
- GLIDE RIDE VALVE
- TELESCOPIC CONTROL VALVE, 3 SECTIONS(CENTER PIVOT)
- HED TELESCOPIC CONTORL VALVE, SECTION HOSES(CENTER PIVOT)
- HED CYLINDER PISTON END HYDRAULIC LINES(CENTER PIVOT)
- HED CYLINDER ROD END HYDRAULIC LINES(CENTER PIVOT)
- FRONT CONTROL VALVE SUPPORT AND TRANSMISSIONS (CENTER PIVOT)
- HYDRAULIC CYLINDER (BUCKET 4X1-6X1)
- BUCKET 4X1 (1 M3) WITH BLADE
- BUCKET 4X1 (1 M3) WITH TINE
- BUCKET 6X1 (1 M3) WITH BLADE
- BUCKET 6X1 (1 M3) WITH TINE
- BOOM - DIPPER SHORT
- SHORT DIPPER
- SHORT DIPPER - BUCKET MOTION
- SHORT DIPPER - HYDRAULIC SYSTEM
- HYDRAULIC BUCKET CYLINDER
- 12" (305MM) BACKHOE BUCKET WITH PIN TEETH
- 12" (305MM) BACKHOE BUCKET WITH BOLT-ON TEETH
- 18" (457MM) BACKHOE BUCKET WITH PIN TEETH
- 18" (457MM) BACKHOE BUCKET WITH BOLT-ON TEETH
- 24" (610MM) BACKHOE BUCKET WITH PIN TEETH
- 24" (610MM) BACKHOE BUCKET WITH BOLT-ON TEETH
- 30" (762MM) BACKHOE BUCKET WITH PIN TEETH
- 30" (762MM) BACKHOE BUCKET WITH BOLT-ON TEETH
- 36" (914MM) BACKHOE BUCKET WITH PIN TEETH
- 36" (914MM) BACKHOE BUCKET WITH BOLT-ON TEETH
- STANDARD 1MC BUCKET WITH FORKS
- STANDARD 1M3 BUCKET WITH FORKS AND EXTRA REVERSIBLE BLADE
- BOLT-ON TOOTH KIT, 12" (305MM) BACKHOE BUCKET
- STANDARD 1M3 BUCKET WITH FORKS AND TINE
- M3 BUCKET AND EXTRA REVERSIBLE BLADE
- BOLT-ON TOOTH KIT, 30" (762MM) BACKHOE BUCKET
- BOLT-ON TOOTH KIT, 36" (914MM) BACKHOE BUCKET
- PIN TOOTH KIT, 12" (305MM) BACKHOE BUCKET
- PIN TOOTH KIT, 30" (762MM) BACKHOE BUCKET
- STANDARD 1MC BUCKET WITH EXTRA REVERSIBLE BLADE
- DITCH CLEANING BUCKET
- FRONT BUCKET TEETH
- LOADER BUCKET REVERSIBLE BLADE
- SCRAB GRAB
- FORK KIT, CONVERTS4X1 BUCKET TO 6X1
- 4X1 & 6X1 BUCKET CONTROL LEVER, CABLE & DECALS
- 4X1 & 6X1 BUCKET HYDRAULIC LINES
- MANUAL HAMMER SYSTEM
- MANUAL HAMMER VALVE
- 4X1 & 6X1 BUCKET HYDRAULIC LINES CENTER PIVOT)
- 4X1 & 6X1 BUCKET CONTROL LEVER, CABLE & DECALS (CENTER PIVOT)
- HYDRAULIC SYSTEM FOR HAMMER (CENTER PIVOT)
- 4X1 & 6X1 BUCKET HYDRAULIC LINES(CENTER PIVOT)
- REAR MECHANICAL QUICK-COUPLING
- FRONT MECHANICAL QUICK-COUPLING
- BOOM - TELESCOPIC DIPPER SHORT
- TELESCOPIC DIPPER SHORT - HYDRAULIC SYSTEM
- TELESCOPIC DIPPER SHORT- BUCKET MOTION
- BODY, HOOD & DRIVER''S POST 3/3
- STABILIZER CONTROL WITHOUT AUTO-UP (CENTER PIVOT)
- LB75.B MODEL IDENTIFICATION (POWER SHUTTLE)
- LOADER CONTROL VALVE, THREE SECTION, CONTROL LEVER (CENTER PIVOT)
- LOADER CONTROL VALVE, CONTROL LEVER & CABLE (SIDE SHIFT & LB115)
- CASE 3 LEVER BACKHOE CONTROLS, CONSOLE & LEVERS
- CASE 3 LEVER BACKHOE CONTROLS, BELLCRANK & SUPPORT
- CASE 3 LEVER BACKHOE CONTROLS, BUCKET TIE-ROD ASSEMBLY
- CASE 3 LEVER BACKHOE CONTROLS, UPPER SWING TIE-ROD ASSEMBLY
- CASE 3 LEVER BACKHOE CONTROLS, DIPPER, SWING & BOOM LINKAGE
- CASE 3 LEVER BACKHOE CONTROLS, SWING CONTROL PEDAL
- LEVER BACKHOE CONTROLS, UPPER TIE-ROD ASSEMBLY (SIDE SHIFT)
- LEVER BACKHOE CONTROLS, LOWER TIE-ROD ASSEMBLY (SIDE SHIFT)
- LEVER BACKHOE CONTROLS, LEVER, BOOT & DECALS (CENTER PIVOT)
- LOCKING VALVE ON BACKHOE LIFT CYLINDER
- ISO 2 LEVER BACKHOE CONTROLS, LEVERS, BOOT & DECALS (CENTER PIVOT)
- THREE-SECTION LOADER CONTROL VALVE LEVER, CABLE & DECALS
- INTERNAL FAN
- A/C HOUSING & FILTERS
- A/C BLOWER & COILS
- HEATER COIL HOSES
- A/C & HEATER CONTROL PANEL
- A/C & HEATER CONSOLE DUCTS
- A/C & HEATER CONVEYOR
- A/C HOUSING SIDE PANELS
- RH CAB TRIM WITH VENT
- A/C & HEATER CAB ROOF DUCTS
- A/C COMPRESSOR ATTACHING GROUP
- STEERING COLUMN, FIXED & ADJUSTABLE
- ROTATING BEACON
- FRONT CONSOLE WITH SPEEDOMETER, 4WD
- SPEED SENSOR(P.SHUTTLE)
- RH CONSOLE WITH INSTRUMENTS
- RH CONSOLE WITH INSTRUMENTS AND DIAGNOSTICS
- ANTITHEFT
- CLOTH SEAT MOUNTING PLATE, ADJUSTING RAILS & 3" SEAT BELT
- AIR RIDE CLOTH SEAT MOUNTING PLATE, ADJUSTING RAILS & 3" SEAT BELT
- VINYL SEAT MOUNTING PLATE, ADJUSTING RAILS & 3" SEAT BELT (ROPS)
- NON-SUSPENSION SEAT CUSHIONS, RELATED PARTS & 3" SEAT BELT
- WHEELS
- FRONT WHEELS, 2WD
- DRIVING WHEELS(4WD)
- VARIATION
- REVERSIBLE STABILIZER FOOT (CENTER PIVOT)
- STABILIZER FOOT STREET PAD (CENTER PIVOT)
- 4WD STEERING LOCK
- CABINET ACCESSORY
Inside this manual
Real pages from this parts catalog (1,099 pages). Open the sample pages (PDF, 474 KB)
- Parts illustration, page 284: COLD START
- Parts illustration, page 420: Mechanical Version
- Parts illustration, page 556: BUCKET 6X1 (1 M3) WITH TINE
Other manuals for this machine
Save 10% on 2 manuals, 15% on 3 or more. Other manuals for the LB75.B are listed below. Editions cover different serial number ranges: check the serial coverage and tick only the ones that match your machine.
Added to your cart. View cart
This is a parts manual
Here's how it compares to the other manual types.
Service manual
Factory repair procedures and technical information such as specifications, troubleshooting, and wiring and hydraulic diagrams, for the models and systems the manual covers. See What's inside for its topics.
Operator's manual
Safe operation, controls, maintenance schedules, lubrication points, inspections, and basic checks. Repair procedures are in the service manual.
Parts manual
Illustrated diagrams with factory part numbers for identifying components and ordering parts. Repair procedures are in the service manual.
What it's used for
Factory manual for in-house farm and construction shop use. Straightforward, complete, and easy to follow. It contains the OEM information dealership service departments and parts counters use to diagnose problems, identify components, and perform maintenance or repairs correctly.
Service shops and owner/operators who repair their own equipment
Identifying correct parts and seeing how assemblies come apart and go back together
Keeping equipment running with less downtime
Factory manual, 1,099 pages
Quantity one is the manual described above.
Fast free USA shipping
Ships in 1 business day.
60-day returns
Free if the mistake is ours. A manual ordered in error must come back unopened in its shrink-wrap; you pay return shipping and a 20% restocking fee applies. Return policy
Binder not included
Manuals over about 300 pages may need a standard 3-ring binder, which you can buy locally to keep the pages organized for shop use.
Other editions and similar models
Questions about model, serial number, engine coverage or contents? Contact us before purchasing and we'll help confirm it's the right manual. Please verify the manual type, machine model, serial number range and engine coverage before purchasing: manuals ordered in error carry a 20% restocking fee (return policy).