New Holland LS L3AL, L3BL Tier 3 Engine Service Manual
305 pages · Publication 47731080
Added to your cart. View cart
- Models
- LS L3AL, L3BL Tier 3
- Manual type
- Service Manual
- Pages
- 305
- Publication
- 47731080
- Condition
- Brand new
What's inside
From the manual's own table of contents: 122 topics. See sample pages (PDF, 361 KB)
- Engine
- Engine and crankcase
- Cylinder heads
- Pan and covers
- Crankshaft and flywheel
- Connecting rods and pistons
- Valve drive and gears
- Pump drives
- Fuel injection system
- Intake and exhaust manifolds and muffler
- Engine lubrication system
- Engine cooling system
- Electrical systems
- Fuel injection system
- Engine cooling system
- Engine oil system
- Engine starting system
- Cold start aid
- Alternator
- Foreword
- Foreword - Important notice regarding equipment servicing
- Safety rules
- Safety rules - Ecology and the environment
- General specification (*)
Show all 122 topics
- Torque
- Torque - Minimum tightening torques for normal assembly
- Special tools
- Dimension
- Component localization
- Dynamic description ventillation
- Identification
- Exploded view (*)
- Check cylinder bores (*)
- Test
- Compression test
- Troubleshooting
- Dimension - Valve springs
- Static description
- Exploded view
- Remove
- Install
- Disassemble and valve removal
- Inspect
- Assemble and valve install
- Install and head gasket install
- Spring - Inspect
- Adjust valve clearance
- Dynamic description
- Exploded view timing gears
- Install seal
- Inspect the flywheel surface
- Inspect - Ring gear
- Replace - Ring gear
- Check face run - out and pilot bearing bore run - out of flywheel
- Remove rear seal and rear end plate
- Check oil seal running surface
- Install rear seal and rear end plate
- Remove Pulley
- Install pulley
- Remove gear
- Install gear
- Remove the crankshaft
- Check run-out
- Install crankshaft
- Check oil clearance of main bearings
- Install main bearings
- Dimension (*)
- Pin - Dimension
- Ring - Dimension
- Detailed view inspection
- Remove piston pins
- Connecting rod - Inspect
- Assemble
- Remove piston rings
- Inspect (*)
- Check gap between piston ring and groove
- Check clearance between ends of piston rings (*)
- Check clearance between piston pin and bore
- Ring - Install
- Check oil clearance
- Push rod - Dimension
- Inspect – Valve seats
- Replace valve seats
- Replace combustion jets
- Remove rocker shaft assemblies
- Disassemble
- Install rocker shaft assemblies
- Remove tappets
- Check tappets for wear and clearance between tappet and bore
- Install tappets
- Remove camshaft and gear
- Install camshaft and gear
- Backlash measurement between the gears
- End play of idler gear check
- End play of camshaft check
- Install Idler gear, Oil pump, and Injection timing
- General specification
- Exploded view ;Sensor, and injection system components
- Exploded view and water sensor
- Timing adjust
- Overview
- Pressure test - Engine oil
- Service instruction
- Remove the oil pressure relief valve
- Install the oil pressure relief valve
- Remove oil pump, - suction pipe and strainer
- Inspect - Pick-up tube
- Install - oil pump, suction pipe and suction strainer
- Exploded view L3BL (*)
- Exploded view L3AL (*)
- Remove L3AL engine (*)
- Remove L3BL engine (*)
- Install L3AL engine (*)
- Install L3BL engine (*)
- Static description - Engine coolant temperature sending unit
- Test - Engine coolant temperature sending unit
- Dynamic description - Engine oil pressure switch
- Test - Engine oil pressure switch
- General specification Starter motor
- Overview glow plugs, hardware and connection plate
- Remove - Glow plug
- Install - Glow plug
Inside this manual
Real pages from this service manual (305 pages). Open the sample pages (PDF, 360 KB)
- Specifications, page 203: Engine - Engine lubrication system
- Troubleshooting, page 223: Engine - Engine lubrication system
- Diagram, page 279: Electrical systems - Engine starting system
This is a service manual
Here's how it compares to the other manual types.
Service manual
Factory repair procedures and technical information such as specifications, troubleshooting, and wiring and hydraulic diagrams, for the models and systems the manual covers. See What's inside for its topics.
Operator's manual
Safe operation, controls, maintenance schedules, lubrication points, inspections, and basic checks. Repair procedures are in the service manual.
Parts manual
Illustrated diagrams with factory part numbers for identifying components and ordering parts. Repair procedures are in the service manual.
Engine service manuals are sometimes sold separately, since certain machine models were offered with more than one engine option.
What it's used for
Factory manual for in-house farm and construction shop use. Straightforward, complete, and easy to follow. It contains the OEM information dealership service departments and parts counters use to diagnose problems, identify components, and perform maintenance or repairs correctly.
Service shops and owner/operators who repair their own equipment
Identifying correct parts and seeing how assemblies come apart and go back together
Keeping equipment running with less downtime
Factory manual, 305 pages
Quantity one is the manual described above.
Fast free USA shipping
Ships in 1 business day.
60-day returns
Free if the mistake is ours. A manual ordered in error must come back unopened in its shrink-wrap; you pay return shipping and a 20% restocking fee applies. Return policy
Binder not included
Manuals over about 300 pages may need a standard 3-ring binder, which you can buy locally to keep the pages organized for shop use.
Questions about model, serial number, engine coverage or contents? Contact us before purchasing and we'll help confirm it's the right manual. Please verify the manual type, machine model, serial number range and engine coverage before purchasing: manuals ordered in error carry a 20% restocking fee (return policy).