New Holland TD4020F, TD4030F, TD4040F Tractor Service Manual
421 pages · Publication 47621082
Added to your cart. View cart
What's inside
From the manual's own table of contents: 19 sections, 202 entries. See sample pages (PDF, 732 KB)
HOLLAND15 topics
- General instructions
- Notes for spare parts
- Notes for equipment
- Safety rules
- Consumables
- Tools
- Engine Troubleshooting
- Engine R.I
- General specifications
- Torque settings
- Section views
- Troubleshooting
- Clutch – Removal–Installation
- Dual disk clutch 11”/11” Test bench overhaul
- Clutch adjustments
SECTION 21 – TRANSMISSIONS – CHAPTER 117 topics
- Main data
- Tightening torques
- Description and operation
- Fault diagnosis
- Gearbox
- Gearing type
- Range gear
- Slow
- Normal
- Fast
- Gearbox and range gear controls
- Inside diameter of gearbox driven gears
- Outside diameter of bushings (17, page 5)
- Clearance between gears and bushings
- Diameter of gearbox driven shaft (19, page 5)
- Inside diameter of bushings (17, page 5)
- Clearance between shaft and bushings
SECTION 21 – TRANSMISSIONS – CHAPTER 25 topics
- Removal–Refitting
- Type
- Control
- Reduction unit
- Gearbox and reduction unit controls
SECTION 21 – TRANSMISSIONS – CHAPTER 31 topic
- Reduction ratio
SECTION 23 – DRIVE LINES – CHAPTER 114 topics
- Main specification
- Torque settings and Tools
- Cross–Sectional views
- Transmission shafts and guard (Disassembly – Assembly)
- Drive gear housing (Removal – Installation)
- Drive gear housing removed (Disassembly – Assembly)
- Relay lever pad width
- Pad seat width in driven gear
- Pad clearance in seat
- Relay lever pivot diameter
- Pivot housing bore in casing
- Pivot clearance in housing
- Free
- Front drive sleeve shim thickness
SECTION 25 – MECHANICAL FRONT AXLE – CHAPTER 19 topics
- Complete front axle. Removal – Installation
- Front axle. Removal – Installation
- Steering knuckle bearing pins. Replacement
- Stub axle adjustment
- Wheel hub bearing adjustment
- Bevel drive adjustment
- Front axle differential. Overhaul
- Front axle differential with LIM–SLIP. Overhaul
- Leading drive wheels toe–in check
SECTION 27 – REAR AXLE AND TRANSMISSION – CHAPTER 119 topics
- Special tools
- Description and operation and troubleshooting
- 21.118.10 – 12 Transmission–gearbox casing Removal–Installation
- Transmission–gearbox casing Disassembly–Overhaul
- Gearbox driven shaft end float adjustment
- Differential lock engagement sleeve adjustment
- Determining the bevel pinion positioning adjustment ring
- Adjusting the taper roller bearings for the bevel pinion shaft
- Adjusting the bearings and checking the backlash
- Differential pinion and side gear backlash adjustment
- Bevel gear pair gear ratio
- Bevel gear pair tooth clearance
- Type of differential
- Elektrohydraulically controlled differential lock
- Differential pinion internal seat diameter
- Differential pinion pin diameter
- Diameter of side gear hub seats on differential box
- Diameter of side gear hubs
- Clearance between side gears and their seats
SECTION 31 – POWER TAKE–OFF – CHAPTER 111 topics
- Sectional drawings
- Removal – Refitting
- Bench overhaul
- Type (Independent and ground speed PTO)
- Engagement and control
- Direction of rotation (viewed from rear of tractor)
- Engine speed with PTO shaft rotating at 540 rev/min
- rev/min
- (4WD 40 km/h version)
- Diameter of PTO shaft at position of bearings
- Diameter of PTO shaft at splined end
SECTION 33 – BRAKING SYSTEM – CHAPTER 114 topics
- Description & Operation
- Tools – Troubleshooting
- Service brake removal and refitting
- Removal–Refitting of brake pumps
- Bleeding air from the braking system
- Adjusting service brake pedals travel
- Parking brake travel adjustment
- service brake
- parking brake
- Disc material for service brake
- Disc material for parking brake
- Mobile sector material for parking brake
- service brakes
- For all models
SECTION 35 – HYDRAULIC SYSTEM – CHAPTER 114 topics
- Hydraulic circuit
- Description and operation of lift phases
- Hydraulic lift – disassembly reassembly
- 35.110.40–42–46 Hydraulic lift – bench overhaul
- Adjusting the lift
- Linkage adjustment
- Pressure relief valve – disassembly reassembly
- Pressure relief valve – setting
- Lift control valve – disassembly assembly and overhaul on bench
- Lift pump
- Operating system
- LIFT–O–MATIC
- Pressure relief valve setting
- Cylinder safety valve setting
SECTION 35 – HYDRAULIC SYSTEM – CHAPTER 210 topics
- Main data – Tools
- Auxiliary control valves – sectional views
- Auxiliary control valves – Assembly–Disassembly
- Spool binding test
- Spool leakage test
- Adjustment of the automatic detent release pressure
- Filter
- Pump
- Location
- Operation
SECTION 35 – HYDRAULIC SYSTEM – CHAPTER 33 topics
- Hydraulic diagram
- Description and operation of valve phases
- Trailer brake auxiliary control valve linkage adjustment
SECTION 41 – STEERING – CHAPTER 111 topics
- Principal data
- Hydrostatic steering control valve – Removal–Installation
- Hydrostatic steering control valve – Disassembly–Assembly
- Hydrostatic steering control valve – Bench testing
- Hydrostatic steering oil pump – Disassembly–Assembly
- Steering cylinder – Removal–Refitting
- Oil filter
- Make
- DANFOSS
- ORSTA
- 4WD models
SECTION 55 – ELECTRICAL SYSTEM – CHAPTER 12 topics
- Analogue instruments Introduction
- INTRODUCTION
SECTION 55 – ELECTRICAL SYSTEM – CHAPTER 22 topics
- Component description
- direction indicators
SECTION 55 – ELECTRICAL SYSTEM – CHAPTER 38 topics
- Technical information
- Starting circuit
- System tests
- Removal and re–installation of starter motor
- Servicing
- Bench tests
- Power (kW)
- Maximum current drain without load (Amp)
SECTION 55 – ELECTRICAL SYSTEM – CHAPTER 47 topics
- System testing and trouble–shooting
- Removal, re–installation and servicing
- Nominal voltage (V)
- Max rotation speed (rpm)
- Maximum output (A)
- Rotor field winding resistance ( )
- Stator field winding resistance ( )
SECTION 55 – ELECTRICAL SYSTEM – CHAPTER 59 topics
- Removal and re–installation
- Battery checking and maintenance
- Charging the battery
- Battery problems – Frequent causes
- Voltage (V)
- Capacity (Ah)
- Number of elements
- Number of plates per element
- Energy reserve (SAE) (min.)
SECTION 55 – ELECTRICAL SYSTEM – CHAPTER 612 topics
- Fuses (all versions)
- Symbols used in electrical circuits
- Electrical wire colour coding
- Ground locations
- Electrical diagrams
- General diagrams
- Start–up circuit
- Direction indicator & hazard warning light circuit
- Brake light circuit
- Work lamp
- Side lights,main and dipped headlights, parking light circuit
- Connector owerview
Inside this manual
Real pages from this service manual (421 pages). Open the sample pages (PDF, 731 KB)
- Troubleshooting, page 43: SECTION 18 – CLUTCH – CHAPTER 1
- Specifications, page 157: SECTION 25 – MECHANICAL FRONT AXLE – CHAPTER 1
- Diagram, page 379: SECTION 55 – ELECTRICAL SYSTEM – CHAPTER 4
- Color page, page 66: SECTION 18 – CLUTCH – CHAPTER 1
- Color page, page 295: SECTION 35 – HYDRAULIC SYSTEM – CHAPTER 2
- Foldout diagram, page 404: SECTION 55 – ELECTRICAL SYSTEM – CHAPTER 6
This is a service manual
Here's how it compares to the other manual types.
Service manual
Factory repair procedures and technical information such as specifications, troubleshooting, and wiring and hydraulic diagrams, for the models and systems the manual covers. See What's inside for its topics.
Operator's manual
Safe operation, controls, maintenance schedules, lubrication points, inspections, and basic checks. Repair procedures are in the service manual.
Parts manual
Illustrated diagrams with factory part numbers for identifying components and ordering parts. Repair procedures are in the service manual.
Engine service manuals are sometimes sold separately, since certain machine models were offered with more than one engine option.
What it's used for
Factory manual for in-house farm and construction shop use. Straightforward, complete, and easy to follow. It contains the OEM information dealership service departments and parts counters use to diagnose problems, identify components, and perform maintenance or repairs correctly.
Service shops and owner/operators who repair their own equipment
Identifying correct parts and seeing how assemblies come apart and go back together
Keeping equipment running with less downtime
Factory manual, 421 pages
Quantity one is the manual described above.
Fast free USA shipping
Ships in 1 business day.
60-day returns
Free if the mistake is ours. A manual ordered in error must come back unopened in its shrink-wrap; you pay return shipping and a 20% restocking fee applies. Return policy
Binder not included
Manuals over about 300 pages may need a standard 3-ring binder, which you can buy locally to keep the pages organized for shop use.
Other editions and similar models
Questions about model, serial number, engine coverage or contents? Contact us before purchasing and we'll help confirm it's the right manual. Please verify the manual type, machine model, serial number range and engine coverage before purchasing: manuals ordered in error carry a 20% restocking fee (return policy).