Snorkel EPV16 Truck Mounted Aerial Work Platform Operator's Manual
97 pages · Publication 13642-1
Fast free USA shippingShips in 1 business daySave 10% on 2 manuals, 15% on 3 or morePay by credit or debit card or with PayPal. No PayPal account needed.
Added to your cart. View cart
- Models
- EPV16
- Serial coverage
- NZ110412 and after
- Manual type
- Operator's Manual
- Pages
- 97
- Publication
- 13642-1
- Condition
- Brand new
What's inside
From the manual's own table of contents: 87 sections, 318 entries. See sample pages (PDF, 865 KB)
Electrical Hazard1 topic
- Electrical Hazard Warning i
Introduction10 topics
- Options ii
- Operation Manual ii
- Photographs ii
- Safety Alerts ii
- Operation ii
- Maintenance iii
- Responsibilities of parties iii
- In summary iii
- Product Warranty iii
- Additional information iii
Chapter 1. Safety12 topics
- Safe Operation 1-1
- Electrocution Hazards 1-1
- Pre-start Inspection 1-1
- Work Place Inspection and Practices 1-1
- Operation 1-2
- Tipover and Falling Hazards 1-2
- General Safety Precautions 1-3
- Hydraulic System Precautions 1-3
- Fire Prevention 1-3
- Engine and Fuel Handling Precautions 1-3
- Batteries 1-4
- Safety Decals and Placards 1-4
Safety - Low Voltage Insulation7 topics
- Owner Responsibility 2-9
- Insulation Maintenance 2-9
- Electrical Safety Certificate 2-9
- Insulation Covering Test 9
- Basket Emergency Exit 2-9
- Earth Point 2-10
- Safety Decals and Placards 2-10
Safety Devices21 topics
- Safety Device Information 3-1
- Emergency Stop SwitchesMachines with Electric Controls 3-1
- At ground control box 3-1
- At platform control box 3-1
- Emergency Stop SwitchesMachines with Hydraulic Controls 3-1
- At ground control box 3-1
- At platform control box(steel platform) 3-2
- At platform control box(insulated fibreglass platform) 3-2
- At platform control box(non-insulated fibreglass platform) 3-2
- Other Safety Devices 3-2
- Lanyard anchor points 3-2
- Gravity gate 3-3
- Guardrails 3-3
- 10.9m height restriction kit (Option) 3-3
- Enable switch 3-3
- Enable switch (foot) 3-4
- Platform Overload Protection 3-4
- Bubble level 3-4
- RCD/ELCB AC outlet 3-5
- Stabiliser/Boom Interlock 3-5
- Flashing light (Option) 3-5
Chapter 4. Specifications9 topics
- General Specifications- Typical 4-1
- Recommended Hydraulic Oil 4-1
- Engine Data 4-2
- Overall Dimensions EPV16 4-2
- Booms identification 4-3
- Nomenclature And Serial Numbers 4-3
- Right side view of machine 4-3
- Left side view of machine 4-4
- Working Envelope 5
Chapter 5. Gauges3 topics
- Hourmeter 5-1
- Level Bubble 5-1
- Hydraulic Oil Level 5-1
Chapter 6. Shut-offs and Circuit Breakers3 topics
- RCD/ELCB Outlet (option) 6-1
- Electrical Circuit Protection 6-1
- Stabilisers 6-1
Controls - Electric8 topics
- Controls Description 7-1
- Controls and Control Decal Locations 7-1
- Ground Control Box 7-2
- Lower controls: 7-2
- Platform Control Box 7-3
- Upper controls: 7-3
- Stabiliser Controls 7-4
- Self Levelling Stabilisers (Option) 7-5
Controls - Hydraulic10 topics
- Controls Description 8-1
- Controls and Control Decal Locations 8-1
- Ground Control Box 8-2
- Lower controls: 8-2
- Platform Control Box 8-3
- Upper controls (steel basket): 8-3
- Upper controls (non-insulated fibreglass basket): 8-5
- Upper controls (insulated fibreglass basket): 8-6
- Stabiliser Controls 8-7
- Self Levelling Stabilisers (Option) 8-7
Pre-operational Inspection41 topics
- Pre-operational Inspection Table 9-1
- Stabiliser/Boom Interlock Test 9-2
- Engine Cover 9-3
- Engine Fuel Level 9-3
- Fuel Tank Cap 9-3
- Fuel Leaks 9-3
- Engine Oil Level 9-3
- Wiring Harnesses 9-3
- Battery Terminals 9-3
- Battery Fluid Level 9-4
- Hydraulic Oil Level 9-4
- Hydraulic Oil Leaks 9-4
- Bolts and Fasteners 9-4
- Structural Damage and Welds 9-5
- Lanyard Anchor Points 9-5
- Platform Gravity Gates 9-5
- Platform Guardrails 9-5
- Flashing Light (option) 9-5
- Ground Control SwitchesMachines with Electric Controls 9-6
- Platform Control Switches Machines with Electric Controls 9-6
- Ground Control SwitchesMachines with Hydraulic Controls 9-7
- Platform Control SwitchesMachines with Hydraulic Controls 9-7
- AC Outlet RCD/ELCB (option) 9-8
- LV Insulated EPV16 9-8
- Insulation Covers 9-8
- Fibreglass Basket 9-8
- Boom insulation Covering 9-8
- Cleanliness 9-9
- Placards and Decals 9-9
- Placards and DecalsMachines with Electric Controls 9-9
- Standard placards and decals 9-9
- Placards and DecalsMachines with Hydraulic Controls 9-9
- Standard placards and decals 9-9
- Placards and DecalsLow Voltage Insulated Machines 9-9
- Standard placards and decals 9-9
- Decal listmachines with electric controls 9-10
- Decal inspection drawingmachines with electric controls 9-11
- Decal listmachines with hydraulic controls 9-12
- Decal inspection drawingmachines with hydraulic controls 9-13
- Decal listlow voltage insulated machines 9-14
- Decal inspection drawinglow voltage insulated machines 9-15
Operation25 topics
- Operating Procedures 10-1
- Control Stations 10-1
- Emergency Stopping 10-1
- Emergency StoppingMachines with Electric Controls 10-1
- Emergency StoppingMachines with Hydraulic Controls 10-1
- Operation Considerations 10-2
- Stabiliser Operation 10-2
- Using the manual stabiliser valves 10-2
- Raising the manually operated stabilisers 10-3
- Self levelling stabilisers (Optional) 10-3
- Setting the stabilisers manually 10-3
- Unlocking the booms 10-3
- Starting From Ground Control BoxMachines with Electric Controls 10-4
- Starting From Platform Control BoxMachines with Electric Controls 10-4
- Moving The PlatformEnable Switches. 10-5
- Moving The PlatformMachines with Electric Controls 10-5
- From ground control box 10-6
- From platform control box 10-6
- Starting From Ground Control BoxMachines with Hydraulic Controls 10-7
- Starting From Platform Control BoxMachines with Hydraulic Controls 10-8
- Moving The PlatformMachines with Hydraulic Controls 10-9
- From ground control box 10-9
- From platform control box 10-9
- Over-Centre valve 10-10
- Securing for Day 10-10
Emergency Operation7 topics
- Emergency Operation Procedures 11-1
- Emergency Operation ProceduresMachines with Hydraulic Controls 11-1
- Operation from platform control stationhydraulic control machines 11-1
- Operation from ground control stationhydraulic control machines 11-2
- Emergency Operation ProceduresMachines with Electric Controls 11-3
- Operation from platform control stationelectric control machines 11-3
- Operation from ground control stationelectric control machines 11-4
Stowing and Transporting2 topics
- Stowing 12-1
- The correct stowed position is shown here. 12-1
Chapter 13. Fire Fighting & Chemical Control1 topic
- Hazardous Components 13-1
Chapter 14. Operator's Troubleshooting2 topics
- Troubleshooting 14-1
- Operator Troubleshooting Chart 14-1
Appendix A. Glossary
AC outlet RCD/ELCB, 9-8
Additional information1 topic
- Introduction - page iv, A-iii
Automatic Shut-offs3 topics
- Circuit Breakers
- Main Circuit Breaker, 6-1
- Stabilisers, 6-1
Basket Emergency Exit, 2-9
Battery fluid level, 9-4
Battery terminals, 9-3
Bolts and fasteners, 9-4
Show all 87 sections
Booms Identification, 4-3
Bubble Level, 8-7
Controls10 topics
- Control levers
- Control switches
- Emergency Lower, 7-3
- Foot Switch, 7-4
- Master Key Switch, 7-2, 9-1
- Stabliser / Boom Secector Switch, 7-2, 8-2
- Ground Control Box, 7-2, 8-2
- Control switches, 7-2, 8-2
- Platform Control Box
- Control switches, 7-3, 8-3
Controls and Control Decals Locations, 7-1
Electrical
Electrical Hazard Warning1 topic
- see Electrical Hazard - page i
Electrical Safety Certificate, 2-9
Emergency lower, 9-6
Emergency Operation, 11-13 topics
- Operation From Ground Control Box, 11-2, 11-4
- Operation From Platform Control Box, 11-1
- Procedures, 11-1
Engine10 topics
- Cooling system, 4-2
- Displacement, 4-2
- Engine oil level, 9-3
- Fuel consumption, 4-2
- Fuel grade, 4-2
- Fuel leaks, 9-3
- Fuel tank cap, 9-3
- Ignition system, 4-2
- Oil capacity, 4-2
- Oil grade, 4-2
Falling hazards, 1-2
Flashing light, 9-5
Gauges3 topics
- Hourmeter, 5-1
- Hydraulic Oil Level, 5-1
- Level Bubble, 5-1
General Specifications, 4-1
Ground Control Box, 7-2
Hazardous Components, 13-1
Hydraulic oil1 topic
- Filler cap, 9-4
Hydraulic oil level, 9-4
Inspection2 topics
- Operators pre-operational inspection, 9-1
- Inspection and Maintenance Table, 9-1
Insulation Maintenance, 2-9
Insulation rating, 4-1
Left side view of machine, 4-4
Light Flashing, 9-5
Lower control box, 9-6
Maintenance personnel1 topic
- see Introduction - page iv
Maximum height to basket floor, 4-1
Maximum outreach, 4-1
Maximum outreach height, 4-1
Nomenclature And Serial Numbers, 4-3
Operating Procedures, 10-15 topics
- Control Stations, 10-1
- Emergency Stopping, 10-1
- Moving The Platform, 10-5
- Starting From Ground Control Box, 10-2
- Starting From Platform Control Box, 10-4
Operation, 10-1
Operators
Other Safety Devices, 3-2
Overall height, 4-1
Placards and decals, 9-91 topic
- Standard placards and decals, 9-9
Platform2 topics
- Foot switch, 10-6
- Lanyard anchor points, 9-5
Platform size, 4-1
Pre-operational Inspection Table, 9-1
Pre-start Inspection, 1-1
Qualified Operators
RCD/ELCB Outlet (option), 6-1
Responsibilities of owners and users
Right side view of machine, 4-3
Safe Operation, 1-1
Safe working load, 4-1
Safety6 topics
- Basket Emergency Exit, 2-9
- Decals and Placards, 2-10
- Earth Point, 2-10
- Electrical Safety Certificate, 2-9
- Insulation Maintenance, 2-9
- Owner Responsibility, 2-9
Safety Alerts, Caution, Danger, Warning, Important1 topic
- see Introduction - page iii
Safety Decals and Placards, 1-4, 2-10
Safety Devices9 topics
- Bubble level, 3-4
- Emergency Stop Switches, 3-1
- Flashing light, 3-5
- Foot switch, 3-3
- Gravity gate, 3-2
- Guardrails, 3-3
- Lanyard anchor points, 3-2
- RCD/ELCB AC outlet, 3-5
- Safety Device Information, 3-1
Safety precautions2 topics
- Fuel Handling Precautions, 1-3
- Hydraulic Systems, 1-3
Securing for Day, 10-10
Stabiliser Controls, 7-4, 8-72 topics
- Automatic Operation, 7-5, 8-7
- Manual Operation, 7-4, 8-7
Standard colour, 4-1
Stowing the EPV16, 12-12 topics
- Boom lock pins, 12-1
- Boom restraints and keepers, 12-1
Structural damage and welds, 9-51 topic
- Boom welds, 9-5
Tipover hazard, 1-2
Travelling height, 4-1
Troubleshooting, 14-11 topic
- Operator Troubleshooting Chart, 14-1
Turntable rotation, 4-1
Upper Controls1 topic
- Fibreglass basket, 8-6
Wiring harnesses, 9-31 topic
- Loose connections, 9-3
Work Place Inspection and Practices, 1-1
Working height, 4-1
Inside this manual
Real pages from this operator's manual (97 pages). Open the sample pages (PDF, 863 KB)
- Specifications, page 30: Chapter 4. Specifications
- Maintenance, page 36: Chapter 5. Gauges
- Controls and operation, page 59: NOTE: - Control Options
- Color page, page 16: Chapter 1. Safety
- Color page, page 80: 11. Emergency Operation
Other manuals for this machine
Save 10% on 2 manuals, 15% on 3 or more. Other manuals for the EPV16 are listed below. Editions cover different serial number ranges: check the serial coverage and tick only the ones that match your machine.
This manual: Operator's Manual 13642-1$69.61
Added to your cart. View cart
This is an operator's manual
Here's how it compares to the other manual types.
Service manual
Factory repair procedures and technical information such as specifications, troubleshooting, and wiring and hydraulic diagrams, for the models and systems the manual covers. See What's inside for its topics.
This manual
Operator's manual
Safe operation, controls, maintenance schedules, lubrication points, inspections, and basic checks. Repair procedures are in the service manual.
Parts manual
Illustrated diagrams with factory part numbers for identifying components and ordering parts. Repair procedures are in the service manual.
What it's used for
Factory manual for in-house farm and construction shop use. Straightforward, complete, and easy to follow. It contains the OEM information dealership service departments and parts counters use to diagnose problems, identify components, and perform maintenance or repairs correctly.
Service shops and owner/operators who repair their own equipment
Identifying correct parts and seeing how assemblies come apart and go back together
Keeping equipment running with less downtime
Factory manual, 97 pages
Quantity one is the manual described above.
Fast free USA shipping
Ships in 1 business day.
60-day returns
Free if the mistake is ours. A manual ordered in error must come back unopened in its shrink-wrap; you pay return shipping and a 20% restocking fee applies. Return policy
Questions about model, serial number, engine coverage or contents? Contact us before purchasing and we'll help confirm it's the right manual. Please verify the manual type, machine model, serial number range and engine coverage before purchasing: manuals ordered in error carry a 20% restocking fee (return policy).