Snorkel S6926RTE, S6933RTE, S6940RTE, S6947RTE Scissor Lift Operator's Manual
81 pages · Publication 1850480-000
Added to your cart. View cart
What's inside
From the manual's own table of contents: 135 topics. See sample pages (PDF, 529 KB)
- Aerial Platform Features
- Options
- Operator’s Manual
- Safety Alerts
- Operation
- Maintenance
- Used Material Disposal
- Manual of Responsibilities – ANSI
- MEWP Safe Use – AS/NZS
- AS/NZS 1418.10 Commissioning
- CE Compliance
- Additional Information
- Component Identification
- General Specifications – S6926RTE
- General Specifications – S6933RTE
- General Specifications – S6940RTE
- General Specifications – S6947RTE
- Electrocution Hazards
- Minimum Safe Approach Distance – ANSI
- Minimum Safe Approach Distance – AS/NZS
- Platform Capacity
- Manual Force
- Wind Speeds
- Prestart Inspection
Show all 135 topics
- Work Place Inspection and Practices
- Tip-Over and Falling Hazards
- Electrical System
- Lithium-Ion Batteries
- Hydraulic System
- Placards and Decals
- General Safety Rules
- Emergency Stop Controls
- Ground Operation Switch
- Upper Control Interlock Switch
- Guardrails
- Fall Protection Anchors
- Ground Fault Circuit Interrupter
- Overload Protection
- ANSI/CSA Machines
- CE/AS/NZS Machines
- Platform Raise/Lower Light
- Platform Overload/Tilt Warning Lights
- Stabilizers – Option
- Stabilizer Down/Lift Interlock
- Stabilizer Indicator Light
- Lowering Alarm
- Emergency Lowering System
- Safety Prop
- Lowering Interrupt – CE/AS/NZS
- Horn
- Drive Motion Alarm
- Flashing Lights
- Snorkel Guard
- Battery Charge Indicator
- Battery Warning Light
- Diagnostic Center Display
- Hydraulic Fluid Filter Gauge
- Hydraulic Fluid Level/Temperature Gauge
- General Maintenance
- Charging
- Battery Disconnect
- Lower Controls
- Diagnostic Center LCD Display
- Emergency Stop Button
- Control Selector Switch
- Start/Ground Operation Switch
- Engine Start
- Stabilizer Auto Level/Stow Switch
- Platform Raise/Lower Switch
- Emergency Lowering Switch
- Upper Controls
- Start/Range Extender – Option
- Drive/Lift Selector Switch
- Drive Range Switch
- Joystick
- Interlock Switch
- Steer Switch
- Stabilizer Controls/Manual – Option
- Stabilizer Controls/Auto Level – Option
- Stabilizer Indicator Light – Option
- Horn Button
- Range Extender Switch – Option
- Batteries
- Battery Terminals
- Cables and Wiring Harness
- Fluid Level
- Hoses, Tubes, and Fittings
- Tires and Wheels
- Lower Control Station
- Operating Controls
- Emergency Stop
- Stabilizer Interlock Test
- Not Locked
- Platform Raise Locked Out When Chassis Tilted
- Structures
- Weldments
- Rollers and Slide Blocks
- Fasteners
- Upper Control Station
- Guardrail System
- Electrical Power Outlet
- Prestart Inspection Checklist
- Cold Weather Start-Up
- Hydraulic System Cold Weather Warm-Up
- Manually Warming The Hydraulic System
- Preparing for Operation
- Stabilizers
- Auto Level – All
- Manual Level – Individual
- Platform
- Raising and Lowering
- Extending – Manual Extension Deck
- Fold Down Guardrails
- Driving and Steering
- Drive Speeds
- Pivoting Rear Axle
- Machine in Stowed Position
- Machine Not in Stowed Position
- Drive/Lift Level Sensor Interlock
- Override Button
- Gradeability
- Percent vs. Degree of Slope
- Driving on a Slope
- Calculating Percent Grade
- Machine Gradeability
- After Use Each Day
- Stowing
- Transporting
- Driving
- Winching
- Lifting With a Forklift
- Securing for Transport
- Storage
- Towing
- Troubleshooting Chart
Inside this manual
Real pages from this operator's manual (81 pages). Open the sample pages (PDF, 528 KB)
- Specifications, page 16: Chapter 2 – Specifications
- Controls and operation, page 39: Chapter 8 – Prestart Inspection
- Maintenance, page 74: Appendix B – Inspection Checklists
- Color page, page 36: S6926RTE/S6933RTE/S6940RTE/S6947RTE – 1850480-000
- Color page, page 6: Warning
Other manuals for this machine
Save 10% on 2 manuals, 15% on 3 or more. Other manuals are listed below. Editions cover different serial number ranges: check the serial coverage and tick only the ones that match your machine.
Added to your cart. View cart
This is an operator's manual
Here's how it compares to the other manual types.
Service manual
Factory repair procedures and technical information such as specifications, troubleshooting, and wiring and hydraulic diagrams, for the models and systems the manual covers. See What's inside for its topics.
Operator's manual
Safe operation, controls, maintenance schedules, lubrication points, inspections, and basic checks. Repair procedures are in the service manual.
Parts manual
Illustrated diagrams with factory part numbers for identifying components and ordering parts. Repair procedures are in the service manual.
What it's used for
Factory manual for in-house farm and construction shop use. Straightforward, complete, and easy to follow. It contains the OEM information dealership service departments and parts counters use to diagnose problems, identify components, and perform maintenance or repairs correctly.
Service shops and owner/operators who repair their own equipment
Identifying correct parts and seeing how assemblies come apart and go back together
Keeping equipment running with less downtime
Factory manual, 81 pages
Quantity one is the manual described above.
Fast free USA shipping
Ships in 1 business day.
60-day returns
Free if the mistake is ours. A manual ordered in error must come back unopened in its shrink-wrap; you pay return shipping and a 20% restocking fee applies. Return policy
Questions about model, serial number, engine coverage or contents? Contact us before purchasing and we'll help confirm it's the right manual. Please verify the manual type, machine model, serial number range and engine coverage before purchasing: manuals ordered in error carry a 20% restocking fee (return policy).