Terex Genie GS-2046, GS-2646, GS-3246 Scissor Lift Service Manual
236 pages · Publication 72972
Added to your cart. View cart
- Models
- Genie GS-2046, GS-2646, GS-3246
- Manual type
- Service Manual
- Pages
- 236
- Publication
- 72972
- Condition
- Brand new
What's inside
From the manual's own table of contents: 85 topics. See sample pages (PDF, 573 KB)
- Important Information
- General Safety Rules
- Machine Specifications
- Performance Specifications
- Hydraulic Specifications
- Manifold Component Specifications
- Hydraulic Hose and Fitting Torque Specifications
- Introduction
- Pre-delivery Preparation Report
- Maintenance Inspection Report
- Perform Pre-operation Inspection
- Perform Function Tests
- Perform 30 Day Service
- Grease the Steer Yokes
- Inspect the Batteries
- Inspect the Electrical Wiring
- Inspect the Tires and Wheels (including castle nut torque)
- Test the Key Switch
- Test the Automotive-style Horn (if equipped)
- Test the Drive Brakes
- Test the Drive Speed - Stowed Position
- Test the Drive Speed - Raised Position
- Perform Hydraulic Oil Analysis
- B-10 Replace the Hydraulic Tank Return Filter
Show all 85 topics
- B-11 Check the Module Tray Latch Components
- Check the Scissor Arm Wear Pads
- Test or Replace the Hydraulic Oil
- Circuit Boards
- Joystick Controller
- Controller Adjustments
- Software Configuration
- Platform
- Platform Extension
- Scissor Assembly, GS-2046
- Scissor Assembly, GS-2646
- Scissor Assembly, GS-3246
- Lift Cylinder
- Manual Platform Lowering Cable, GS-2046 and GS-2646
- Manual Platform Lowering, GS-3246
- Toggle Switches
- Control Relays
- Tilt Level Sensor (before serial number 50444)
- Tilt Level Sensor (after serial number 50443)
- Function Pump
- (after serial number 36044)
- Function Manifold Components - Models with Traction Control
- Valve Adjustments - Function Manifold
- (before serial number 36045)
- Valve Coils
- Hydraulic Tank
- Yoke and Drive Motor
- Steer Cylinder
- Steer Bellcrank
- Drive Brake
- Brake Release Hand Pump Components
- Fault Code Chart (after serial number 17407) - Rev A
- All Functions Will Not Operate - Rev A
- Pump Motor Will Not Operate - Rev A
- All Functions Inoperative, Power Unit Starts and Runs - Rev A
- Platform Controls Operate Normally - Rev A
- Ground Controls Operate Normally - Rev A
- Platform Up Function Inoperative - Rev A
- Platform Down Function Inoperative - Rev A
- Steer Left Function Inoperative - Rev A
- Steer Right Function Inoperative - Rev A
- All Other Functions Operate Normally - Rev A
- Brake Release Function Inoperative - Rev A
- Drive Forward Function Inoperative - Rev A
- Drive Reverse Function Inoperative - Rev A
- Machine Will Not Drive At Full Speed - Rev A
- Machine Drives At Full Speed With Platform Raised - Rev A
- Limit Switch Function Inoperative - Rev A
- Fault Code 02 - ECM / Platform Communication Error - Rev A
- Fault Code 59 - Parallel/Series Coil Fault - Rev B
- Control Relay Layout - Rev A
- ECM Pin-out Legend - Rev B
- (after serial number 48054) - Rev A
- Ground Controls Wiring Diagram, GS-2046 and GS-2646 - Rev B
- Ground Controls Wiring Diagram, GS-3246 - Rev B
- Level Sensor Box Wiring Diagram - Rev A
- Electrical Symbols Legend - Rev B
- (after serial number 49199) - Rev A
- Hydraulic Symbols Legend and Component Reference - Rev B
- (after serial number 36044) - Rev A
- Models with Traction Control - Rev A
Inside this manual
Real pages from this service manual (236 pages). Open the sample pages (PDF, 572 KB)
- Specifications, page 15: Section 2 • Specifications
- Troubleshooting, page 129: Section 5 • Troubleshooting Flow Charts
- Diagram, page 228: Hydraulic Schematic
- Foldout diagram, page 199: Electrical Schematic
Other manuals for this machine
Save 10% on 2 manuals, 15% on 3 or more. Other manuals are listed below. Editions cover different serial number ranges: check the serial coverage and tick only the ones that match your machine.
Added to your cart. View cart
This is a service manual
Here's how it compares to the other manual types.
Service manual
Factory repair procedures and technical information such as specifications, troubleshooting, and wiring and hydraulic diagrams, for the models and systems the manual covers. See What's inside for its topics.
Operator's manual
Safe operation, controls, maintenance schedules, lubrication points, inspections, and basic checks. Repair procedures are in the service manual.
Parts manual
Illustrated diagrams with factory part numbers for identifying components and ordering parts. Repair procedures are in the service manual.
Engine service manuals are sometimes sold separately, since certain machine models were offered with more than one engine option.
What it's used for
Factory manual for in-house farm and construction shop use. Straightforward, complete, and easy to follow. It contains the OEM information dealership service departments and parts counters use to diagnose problems, identify components, and perform maintenance or repairs correctly.
Service shops and owner/operators who repair their own equipment
Identifying correct parts and seeing how assemblies come apart and go back together
Keeping equipment running with less downtime
Factory manual, 236 pages
Quantity one is the manual described above.
Fast free USA shipping
Ships in 1 business day.
60-day returns
Free if the mistake is ours. A manual ordered in error must come back unopened in its shrink-wrap; you pay return shipping and a 20% restocking fee applies. Return policy
Other editions and similar models
Questions about model, serial number, engine coverage or contents? Contact us before purchasing and we'll help confirm it's the right manual. Please verify the manual type, machine model, serial number range and engine coverage before purchasing: manuals ordered in error carry a 20% restocking fee (return policy).