Terex Genie SX-135 XC Telescopic Boom Lift Service Manual
250 pages · Publication 1263383
Added to your cart. View cart
- Models
- Genie SX-135 XC
- Serial coverage
- SX135XCH-101
- Manual type
- Service Manual
- Pages
- 250
- Publication
- 1263383
- Condition
- Brand new
What's inside
From the manual's own table of contents: 65 sections, 129 entries. See sample pages (PDF, 915 KB)
Section 3 Repair Procedures27 topics
- Introduction
- Platform Controls
- Platform Circuit Board
- How to Remove the LED Circuit Board
- Joysticks
- How to Reset a Proportional Valve Coil Default
- How to Set the Function Thresholds and Default Functions Speeds
- How to Adjust the Function Speeds
- How to Adjust the Function Ramp Rate Setting
- Platform Components
- Platform
- Platform Leveling Cylinder
- Platform Rotator
- How to Bleed the Platform Rotator
- Platform Level Sensor
- Platform Overload System
- How to Calibrate the Platform Overload System
- How to Perform a Zero Load Cell Calibration
- How to Replace the Platform Overload Load Cell
- Platform Overload Recovery Message
- Jib Boom Components
- Jib Boom
- Jib Boom Lift Cylinder
- Jib Boom Level Cylinder
- Jib Boom Extension Cylinder
- How to Remove the Jib Boom Bellcrank
- Jib Boom Bellcrank Angle Sensor
Primary Boom2 topics
- How to Remove the Primary boom
- How to Disassemble the Primary Boom
Show all 65 sections
Boom Extend and Retract Cables1 topic
- How to Replace the Boom Extend/Retract Cables
Flex Plate1 topic
- How to Install the Flex Plate
Function Pump3 topics
- How to Prime the Function Pump
- How to Adjust the Function Pump Standby Pressure
- How to Adjust the Function Pump Pressure Compensator
Drive Pump25 topics
- How to Prime the Drive Pump
- Manifolds
- Function Manifold Components
- Valve Adjustments - Function Manifold
- Jib Manifold Components
- Platform and Rotator Manifold Components
- Steer and Axle Manifold Components
- Function Enable Manifold
- Valve Adjustments - Steer and Axle Manifold
- Traction Manifold Components
- Valve Adjustments - Traction Manifold
- Generator Manifold Component
- Valve Coils
- Turntable Rotation Components
- Turntable Rotation Assembly
- How to Adjust the Turntable Rotation Gear Backlash
- Turntable Level Sensor
- Axle Components
- Steer Sensors
- How to Calibrate All Steer Sensors
- Steer Cylinders
- Axle Extension Cylinders
- Axle Angle Sensors
- Generators
- Welder Generator
Section 4 Fault Codes5 topics
- Control System Fault Codes
- Fault Matrix
- Fault Code Source
- Deutz TD 2.9 L4 Engine Fault Codes
- Perkins 854F-34T Engine Fault Code
Inside this manual
Real pages from this service manual (250 pages). Open the sample pages (PDF, 914 KB)
- Specifications, page 13: Specifications
- Troubleshooting, page 145: Fault Codes
- Diagram, page 238: Perkins 854F-34T Engine Electrical Schematic
- Foldout diagram, page 249: S56PRV-RD
Other manuals for this machine
Save 10% on 2 manuals, 15% on 3 or more. Other manuals for the Genie SX-135 XC are listed below. Editions cover different serial number ranges: check the serial coverage and tick only the ones that match your machine.
Added to your cart. View cart
This is a service manual
Here's how it compares to the other manual types.
Service manual
Factory repair procedures and technical information such as specifications, troubleshooting, and wiring and hydraulic diagrams, for the models and systems the manual covers. See What's inside for its topics.
Operator's manual
Safe operation, controls, maintenance schedules, lubrication points, inspections, and basic checks. Repair procedures are in the service manual.
Parts manual
Illustrated diagrams with factory part numbers for identifying components and ordering parts. Repair procedures are in the service manual.
Engine service manuals are sometimes sold separately, since certain machine models were offered with more than one engine option.
What it's used for
Factory manual for in-house farm and construction shop use. Straightforward, complete, and easy to follow. It contains the OEM information dealership service departments and parts counters use to diagnose problems, identify components, and perform maintenance or repairs correctly.
Service shops and owner/operators who repair their own equipment
Identifying correct parts and seeing how assemblies come apart and go back together
Keeping equipment running with less downtime
Factory manual, 250 pages
Quantity one is the manual described above.
Fast free USA shipping
Ships in 1 business day.
60-day returns
Free if the mistake is ours. A manual ordered in error must come back unopened in its shrink-wrap; you pay return shipping and a 20% restocking fee applies. Return policy
Questions about model, serial number, engine coverage or contents? Contact us before purchasing and we'll help confirm it's the right manual. Please verify the manual type, machine model, serial number range and engine coverage before purchasing: manuals ordered in error carry a 20% restocking fee (return policy).