Terex Genie Z-34/22 IC Articulated Boom Lift Service Manual
185 pages · Publication 128267
Added to your cart. View cart
- Models
- Genie Z-34/22 IC
- Serial coverage
- from SN 3242 to 4799
- Manual type
- Service Manual
- Pages
- 185
- Publication
- 128267
- Condition
- Brand new
What's inside
From the manual's own table of contents: 107 topics. See sample pages (PDF, 627 KB)
- Important Information
- Serial Number Information
- Serial Number Legend
- General Safety Rules
- Machine Specifications
- Performance Specifications
- Hydraulic Oil Specifications
- Hydraulic Component Specifications
- Manifold Component Specifications
- Machine Torque Specifications
- Kubota D-905 Engine Specifications
- Kubota DF-752 Engine Specifications
- Perkins 403C-11 Engine Specifications
- Hydraulic Hose and Fitting Torque Specifications
- SAE and Metric Fastener Torque Charts
- Introduction
- Pre-Delivery Preparation
- Maintenance Inspection Report
- Inspect the Manuals and Decals
- Perform Pre-operation Inspection
- Perform Function Tests
- Perform Engine Maintenance
- Perform 30 Day Service
- Inspect the Engine Air Filter
Show all 107 topics
- Perform Engine Maintenance - Kubota Models
- A-10 Grease the Turntable Rotation Bearing and Worm Drive Gear
- A-11 Perform Engine Maintenance - Kubota Models
- A-12 Drain the Fuel Filter/Water Separator - Diesel Models
- Check the Engine Choke - Gasoline/LPG Models
- Check the Exhaust System
- Inspect the Battery
- Inspect the Electrical Wiring
- Inspect the Tires, Wheels and Lug Nut Torque
- Confirm the Proper Brake Configuration
- Check the Oil Level in the Drive Hubs
- Perform Engine Maintenance - Perkins 403C-11 Models
- Check and Adjust the Engine RPM
- B-10 Test the Ground Control Override
- B-11 Test the Platform Self-leveling
- B-12 Test the Engine Idle Select
- B-13 Test the Fuel Select Operation - Gasoline/LPG Models
- B-14 Test the Drive Brakes
- B-15 Test the Drive Speed - Stowed Position
- B-16 Test the Drive Speed - Raised or Extended Position
- B-17 Inspect the Fuel and Hydraulic Tank Cap Venting Systems
- B-18 Perform Hydraulic Oil Analysis
- B-19 Test the Alarm Package (if equipped)
- Diesel Models
- B-21 Perform Engine Maintenance - Kubota D905 Models
- Grease the Platform Overload Mechanism (if equipped)
- Test the Platform Overload System (if equipped)
- Clean the Fuel Tank - Diesel Models
- Perform Engine Maintenance - Diesel Models
- Perform Engine Maintenance - Kubota D905 Models
- Check the Primary Boom Wear Pads
- Check the Free-wheel Configuration
- Replace the Drive Hub Oil
- Replace the Hydraulic Filters
- Check the Turntable Rotation Bearing Bolts
- Inspect for Turntable Bearing Wear
- Test or Replace the Hydraulic Oil
- Grease the Steer Axle Wheel Bearings, 2WD Models
- Drive Joystick
- Boom Function Speed Controller
- Platform Leveling Slave Cylinder
- Platform Rotator
- Platform Overload System (if equipped)
- Jib Boom
- Jib Boom Bell Crank
- Jib Boom Lift Cylinder
- Plastic Cable Track
- Primary Boom
- Primary Boom Lift Cylinder
- Extension Cylinder
- Platform Leveling Master Cylinder
- Secondary Boom
- Secondary Boom Lift Cylinder
- Timing Adjustment
- Glow Plugs
- RPM Adjustment
- Flex Plate
- Coolant Temperature and Oil Pressure Switches
- Choke Adjustments
- Carburetor Adjustment
- Auxiliary Pump
- Function Pump
- Drive Pump
- Function Manifold Components
- Valve Adjustments - Function Manifold
- Jib Boom / Platform Rotate Manifold Components
- Brake / 2-speed Manifold Components, 2WD Models
- 2WD Traction Manifold Components
- 4WD Traction Manifold Components
- Valve Adjustments - Traction Manifold
- Valve Coils
- Fuel Tank
- Hydraulic Tank
- Rotation Hydraulic Motor
- Hub and Bearings, 2WD Models
- Electrical Symbols Legend
- Hydraulic Symbols Legend
- Generator Option Wiring Diagram (from serial number 3242 to 4081)
- Generator Option Wiring Diagram (from serial number 4082 to 4799)
- Load Sense Option Wiring Diagram (from serial number 3242 to 3577)
- Manifold and Limit Switch Wiring
- Hydraulic Schematic, 2WD Models
- Hydraulic Schematic, 4WD Models
Inside this manual
Real pages from this service manual (185 pages). Open the sample pages (PDF, 626 KB)
- Specifications, page 22: Section 2 • Specifications
- Repair procedure, page 84: Jib Boom Bell Crank
- Diagram, page 178: Hydraulic Schematic, 2WD Models
- Foldout diagram, page 159: Ground Control Box Wiring Diagram -
Other manuals for this machine
Save 10% on 2 manuals, 15% on 3 or more. Other manuals for the Genie Z-34/22 IC are listed below. Editions cover different serial number ranges: check the serial coverage and tick only the ones that match your machine.
Added to your cart. View cart
This is a service manual
Here's how it compares to the other manual types.
Service manual
Factory repair procedures and technical information such as specifications, troubleshooting, and wiring and hydraulic diagrams, for the models and systems the manual covers. See What's inside for its topics.
Operator's manual
Safe operation, controls, maintenance schedules, lubrication points, inspections, and basic checks. Repair procedures are in the service manual.
Parts manual
Illustrated diagrams with factory part numbers for identifying components and ordering parts. Repair procedures are in the service manual.
Engine service manuals are sometimes sold separately, since certain machine models were offered with more than one engine option.
What it's used for
Factory manual for in-house farm and construction shop use. Straightforward, complete, and easy to follow. It contains the OEM information dealership service departments and parts counters use to diagnose problems, identify components, and perform maintenance or repairs correctly.
Service shops and owner/operators who repair their own equipment
Identifying correct parts and seeing how assemblies come apart and go back together
Keeping equipment running with less downtime
Factory manual, 185 pages
Quantity one is the manual described above.
Fast free USA shipping
Ships in 1 business day.
60-day returns
Free if the mistake is ours. A manual ordered in error must come back unopened in its shrink-wrap; you pay return shipping and a 20% restocking fee applies. Return policy
Other editions and similar models
Questions about model, serial number, engine coverage or contents? Contact us before purchasing and we'll help confirm it's the right manual. Please verify the manual type, machine model, serial number range and engine coverage before purchasing: manuals ordered in error carry a 20% restocking fee (return policy).