Bobcat 430 Excavator Service Manual
1,439 pages · Publication 6902318_4_08
Added to your cart. View cart
- Models
- 430
- Serial coverage
- SN 562511001 & above, SN 562711001 & above, SN 562911001 & above, SN 563011001 & above
- Manual type
- Service Manual
- Pages
- 1,439
- Publication
- 6902318_4_08
- Condition
- Brand new
What's inside
From the manual's own table of contents: 16 sections, 169 entries. See sample pages (PDF, 452 KB)
SAFETY INSTRUCTIONS1 topic
- Fire Prevention
SERIAL NUMBER LOCATIONS2 topics
- Excavator Serial Number
- Engine Serial Number
SAFETY AND MAINTENANCE18 topics
- LIFTING AND BLOCKING THE EXCAVATOR
- UPPERSTRUCTURE SLEW LOCK
- LIFTING THE EXCAVATOR
- OPERATOR CAB (ROPS/TOPS)
- TRANSPORTING THE EXCAVATOR
- TAILGATE
- RIGHT SIDE COVER
- SERVICE SCHEDULE
- AIR CLEANER
- HEATER AIR FILTER (WITH CAB OPTION ONLY)
- COOLING SYSTEM
- FUEL SYSTEM
- ENGINE LUBRICATION SYSTEM
- HYDRAULIC SYSTEM
- LUBRICATION OF THE HYDRAULIC EXCAVATOR
- TRAVEL MOTOR
- SPARK ARRESTOR MUFFLER
- ENGINE ACCESSORY DRIVE BELT
HYDRAULIC SYSTEM34 topics
- HYDRAULIC/HYDROSTATIC SCHEMATICS
- HYDRAULIC SYSTEM INFORMATION
- BOOM CYLINDER
- ARM CYLINDER
- BOOM SWING CYLINDER
- BUCKET CYLINDER
- BLADE CYLINDER
- CLAMP CYLINDER
- ANGLE BLADE CYLINDER
- MAIN RELIEF VALVES
- PORT RELIEF VALVES
- CROSSPORT RELIEF VALVES
- PRESSURE REDUCING VALVE
- ANGLE BLADE VALVE
- HYDRAULIC CONTROL VALVE (S/N 562912779 & Above)
- HYDRAULIC CONTROL VALVE (S/N 563012776 & ABOVE)
- MANIFOLD ASSEMBLY/ACCUMULATOR (S/N 562911001 & ABOVE)
- SWIVEL JOINT
- SWING MOTOR
- SWING MOTOR DRIVE CARRIER
- CONTROL PATTERN SELECTOR VALVE
- RIGHT CONTROL LEVER (JOYSTICK)
- LEFT CONTROL LEVER (JOYSTICK)
- TRAVEL CONTROL VALVE (S/N 562911001 & ABOVE)
- HOSES
- HYDRAULIC FILTER MOUNT
- HYDRAULIC RESERVOIR
- OIL COOLER
- DIRECT TO TANK VALVE (IF EQUIPPED)
- BUILD UP VALVE
- CASE DRAIN FILTER
- COOLING FAN
- BOOM SWING LOCK VALVE
- HYDRAULIC X-CHANGE VALVE
HYDROSTATIC SYSTEM6 topics
- HYDROSTATIC SYSTEM INFORMATION
- TRAVEL PILOT PRESSURE
- HYDROSTATIC PUMP
- FAN/CHARGE PUMP
- DRIVE BELT SHIELD
- DRIVE BELT
UNDERCARRIAGE11 topics
- BLADE
- ANGLE BLADE ASSEMBLY
- ANGLE BLADE
- ANGLE BLADE CUTTING EDGE
- TRACKS
- TRACK FRAME
- TRACK DAMAGE IDENTIFICATION
- TRACK IDLER
- UPPER TRACK ROLLER
- LOWER TRACK ROLLER
- SWING CIRCLE GEAR
UPPERSTRUCTURE & SWING SECTION19 topics
- UPPERSTRUCTURE
- ROPS CANOPY
- SEAT AND SEAT MOUNT
- RIGHT CONSOLE
- LEFT CONSOLE
- ENGINE SPEED CONTROL
- BLADE CONTROL
- RIGHT PEDAL AND LINKAGE
- TRAVEL CONTROLS
- CONTROL LINKAGE ASSEMBLY
- FLOOR MAT AND FLOOR PLATES
- FUEL TANK
- HORN
- SWING FRAME
- BOOM
- BUCKET
- X-CHANGE™
- X-CHANGE (HYDRAULIC)
- COUNTERWEIGHT
ELECTRICAL SYSTEM AND ANALYSIS10 topics
- ELECTRICAL SCHEMATICS
- ELECTRICAL SYSTEM INFORMATION
- BATTERY
- ALTERNATOR
- STARTER
- LIGHTS
- TWO SPEED SWITCH
- FUEL LEVEL SENDER
- DIAGNOSTICS SERVICE CODE
- DELUXE INSTRUMENT PANEL SETUP
ENGINE SERVICE8 topics
- TROUBLESHOOTING
- MUFFLER
- RADIATOR
- ENGINE COMPONENTS AND TESTING
- ENGINE
- ENGINE FLYWHEEL (EARLY MODELS)
- ENGINE FLYWHEEL (LATER MODELS)
- RECONDITIONING THE ENGINE
HEATING, VENTILATION, AIR CONDITIONING29 topics
- HEATER COIL (EARLY MODELS)
- HEATER COIL (LATER MODELS)
- BLOWER FAN (EARLY MODELS)
- BLOWER FAN (LATER MODELS)
- HEATER VALVE
- AIR CONDITIONING SYSTEM FLOW
- COMPONENTS
- SAFETY
- REGULAR MAINTENANCE
- BASIC TROUBLESHOOTING (EARLY MODELS)
- BASIC TROUBLESHOOTING (LATER MODELS)
- GENERAL AIR CONDITIONING SERVICE GUIDELINES
- SYSTEM TROUBLESHOOTING CHART
- TEMPERATURE/PRESSURE
- AIR CONDITIONING SERVICE
- SYSTEM CHARGING AND RECLAMATION
- COMPRESSOR
- CONDENSER
- RECEIVER/DRIER
- PRESSURE RELIEF VALVE
- PRESSURE SWITCH
- EVAPORATOR/HEATER UNIT (EARLY MODELS)
- EVAPORATOR/HEATER UNIT (later MODELS)
- THERMOSTAT (EARLY MODELS)
- THERMOSTAT (LATER MODELS)
- EXPANSION VALVE (EARLY MODELS)
- EXPANSION VALVE (LATER MODELS)
- EVAPORATOR (EARLY MODELS)
- EVAPORATOR (LATER MODELS)
SPECIFICATIONS15 topics
- ENGINE SPECIFICATIONS
- TORQUE SPECIFICATIONS
- HYDRAULIC CONNECTION SPECIFICATIONS
- HYDRAULIC FLUID SPECIFICATIONS
- FUEL, COOLANT AND LUBRICANTS
- CONVERSIONS
- Revision No: 430-1
- Revision No: 430-2
- Revision No: 430-3
- Revision No: 430-4
- Revision No: 430-5
- Revision No: 430-6
- Revision No: 430-7
- Revision No: 430-8
- Revision No: 430-9
Inside this manual
Real pages from this service manual (1,439 pages). Open the sample pages (PDF, 451 KB)
- Diagram, page 1,226: ENGINE
- Troubleshooting, page 1,314: 430 Excavator
- Specifications, page 1,380: SPECIFICATIONS
- Foldout diagram, page 1,149: BATTERY FEED 1000-1999 RED, RED/WHT, RNG
This is a service manual
Here's how it compares to the other manual types.
Service manual
Factory repair procedures and technical information such as specifications, troubleshooting, and wiring and hydraulic diagrams, for the models and systems the manual covers. See What's inside for its topics.
Operator's manual
Safe operation, controls, maintenance schedules, lubrication points, inspections, and basic checks. Repair procedures are in the service manual.
Parts manual
Illustrated diagrams with factory part numbers for identifying components and ordering parts. Repair procedures are in the service manual.
Engine service manuals are sometimes sold separately, since certain machine models were offered with more than one engine option.
What it's used for
Factory manual for in-house farm and construction shop use. Straightforward, complete, and easy to follow. It contains the OEM information dealership service departments and parts counters use to diagnose problems, identify components, and perform maintenance or repairs correctly.
Service shops and owner/operators who repair their own equipment
Identifying correct parts and seeing how assemblies come apart and go back together
Keeping equipment running with less downtime
Factory manual, 1,439 pages
Quantity one is the manual described above.
Fast free USA shipping
Ships in 1 business day.
60-day returns
Free if the mistake is ours. A manual ordered in error must come back unopened in its shrink-wrap; you pay return shipping and a 20% restocking fee applies. Return policy
Binder not included
Manuals over about 300 pages may need a standard 3-ring binder, which you can buy locally to keep the pages organized for shop use.
Other editions and similar models
Questions about model, serial number, engine coverage or contents? Contact us before purchasing and we'll help confirm it's the right manual. Please verify the manual type, machine model, serial number range and engine coverage before purchasing: manuals ordered in error carry a 20% restocking fee (return policy).