Case Axial Flow 5088, 6088, 7088 Combine Service Manual
799 pages · Publication 84242798
Added to your cart. View cart
- Models
- Axial Flow 5088, 6088, 7088
- Manual type
- Service Manual
- Pages
- 799
- Publication
- 84242798
- Condition
- Brand new
What's inside
From the manual's own table of contents: 144 sections, 269 entries. See sample pages (PDF, 1162 KB)
General32 topics
- TORQUE SPECIFICATIONS - DECIMAL HARDWARE
- TORQUE SPECIFICATIONS - METRIC HARDWARE
- TORQUE SPECIFICATIONS - STEEL HYDRAULIC FITTINGS
- LOCTITE CHART
- Nozzle Drive Motor
- Removal
- Installation
- Vacuum Fan and Rotating Arm
- SPECIFICATIONS
- SPECIAL TORQUES
- SPECIAL TOOLS
- ENGINE REMOVAL
- ENGINE INSTALLATION
- SCHEMATIC COLOR LEGEND
- SUBSYSTEM INDEX
- ACTUATORS
- POWER DISTRIBUTION
- STARTING AND CHARGING SYSTEM
- CHASSIS GROUNDS
- CHASSIS GROUNDING POINT LOCATIONS
- CLEAN GROUNDS
- POWER DISTRIBUTION (FUSE BLOCKS)
- UNLOADER CONTROL
- GRAIN TANK COVERS CONTROL
- CHAFFER SPREADER CONTROL
- BACKUP ALARM
- FEEDER AND SEPARATOR CONTROL
- SPREADER PATTERN CONTROL
- HEADER SELECTOR VALVE/DECK PLATE CONTROL
- CONCAVE CONTROL WITH PRESET MACHINES
- FAN CONTROL WITH PRESET MACHINES
- ROTOR CONTROL WITH PRESET MACHINES
Show all 145 sections
STARTER SYSTEM TROUBLESHOOTING24 topics
- STEERING CYLINDER
- Wheel Bearings
- DIsassembly
- Assembly
- Servicing the Steering Tie Rod End
- Toe in Adjustment
- Steering Axle Assembly
- Axle Extension Positions
- Height Positions
- Width Positions
- Center Section
- Steering Knuckle
- Bushing Replacement
- Motor Removal
- Power Guide Axle - Exploded View
- Motor Installation
- Inspection
- PROPULSION SYSTEM AIR REMOVAL
- Combines without Power Guide Wheels
- Combines with Power Guide Wheels
- Illustration of One Speed and Two Speed Hydrostatic Motors
- TRANSMISSION REMOVAL AND INSTALLATION
- ILLUSTRATION OF TRANSMISSION REMOVAL
- GEAR SHIFT CONTROL CABLE ADJUSTMENT
Assembly40 topics
- GENERAL INTRODUCTION
- BASIC PRINCIPLES OF THE HYDRAULIC SYSTEM
- LOAD SENSE SIGNAL TO PFC PUMP COMPENSATOR
- HYDRAULIC SYSTEM COMPONENT LOCATION
- HYDRAULIC SYSTEM RESERVOIR
- HYDRAULIC SYSTEM PRESSURE SCREEN
- HYDRAULIC SYSTEM FILTRATION
- PISTON PUMP AND COMPENSATOR VALVE
- PFC PUMP SYSTEM SCHEMATIC
- PFC PUMP SYSTEM
- PFC PUMP EXPLODED VIEW
- AUXILIARY PUMP SYSTEM
- FEEDER DRIVE HYDRAULICS
- CHAFF SPREADER (OPTIONAL)
- CHAFF SPREADER HYDRAULICS
- MAIN VALVE COMPONENT LOCATIONS
- STATIONARY AIR SCREEN (SAS) SYSTEM
- STATIONARY AIR SCREEN (SAS) HYDRAULIC SYSTEM
- FEEDER REVERSER SYSTEM
- FEEDER REVERSER HYDRAULICS
- STEERING SYSTEM
- STEERING RELIEF SETTING AND ADJUSTMENT
- HIGH PRESSURE STANDBY CHECK AND ADJUSTMENT
- LOW PRESSURE STANDBY CHECK AND ADJUSTMENT
- PRESSURE REGULATOR VALVE PRESSURE CHECK (400 PSI)
- REGULATED PRESSURE CHECK (290 to 320 PSI) AND ADJUSTMENT
- REEL DRIVE RELIEF PRESSURE CHECK AND ADJUSTMENT
- Disassembly and Inspection
- REMOVING AIR FROM THE HYDRAULIC SYSTEM
- SAFETY PROCEDURES
- ACCESSING THE EVAPORATOR/HEATER ASSEMBLY
- THEORY OF OPERATION
- Serviceable Components - Automatic Temperature Control (ATC)
- ATC Systems
- Temperature Range
- Smart Pressure Switch Cycling System
- A/C OPERATION
- ATC WIRING SCHEMATIC
- ATC TROUBLESHOOTING
- ATC Electrical Troubleshooting
ATC COMPONENT LOCATIONS29 topics
- AIR CONDITIONER SYSTEM REFRIGERANT RECOVERY
- A/C Compressor
- Oil Level Check or Adjustment
- Injection Method
- Dipstick Method
- Compressor Belt Adjustment
- AIR CONDITIONER SYSTEM EVACUATION AND RECHARGING
- AXIAL FLOW AIR CONDITIONING TEMPERATURE/PRESSURE CHART
- COMPRESSOR CLUTCH
- THERMAL EXPANSION VALVE TESTING
- THERMAL EXPANSION VALVE REPLACEMENT
- ATC COMPONENTS
- CONDENSER, RECEIVER-DRIER AND TUBES
- INSTALLATION OF EVAPORATOR TEMPERATURE SENSOR
- HEATER AND EVAPORATOR CORE
- Accessing the A/C Unit
- Heater And Evaporator Core Removal
- Heater and Evaporator Core Installation
- AUTOMATIC TEMPERATURE CONTROL MODULE REPLACEMENT
- CAB RECIRCULATION AIR FILTER SERVICE
- CAB AIR INTAKE FILTER SERVICE
- CAB PRESSURIZATION TEST
- FEEDER HOUSING
- ROTOR
- Inspection And Repair
- REPLACING THE ROTOR FRONT BEARING
- WITHOUT REMOVING THE ROTOR
- Rotor Impeller Blade Clearance Check
- FEEDER AND CLEANING FAN GEARBOX
Inside this manual
Real pages from this service manual (799 pages). Open the sample pages (PDF, 1161 KB)
- Diagram, page 226: CONNECTOR C193 - LOCATED RIGHT SIDE
- Repair procedure, page 406: PTO HOUSING SERVICE
- Specifications, page 526: CAB TEMPERATURE CHECK
- Color page: Template Name: SM_2_col
- Color page: Template Name: SM_2_col
- Foldout diagram (color): FRAME 53
Other manuals for this machine
Save 10% on 2 manuals, 15% on 3 or more. Other manuals for the Axial Flow 5088, 6088, 7088 are listed below. Editions cover different serial number ranges: check the serial coverage and tick only the ones that match your machine.
Added to your cart. View cart
This is a service manual
Here's how it compares to the other manual types.
Service manual
Factory repair procedures and technical information such as specifications, troubleshooting, and wiring and hydraulic diagrams, for the models and systems the manual covers. See What's inside for its topics.
Operator's manual
Safe operation, controls, maintenance schedules, lubrication points, inspections, and basic checks. Repair procedures are in the service manual.
Parts manual
Illustrated diagrams with factory part numbers for identifying components and ordering parts. Repair procedures are in the service manual.
Engine service manuals are sometimes sold separately, since certain machine models were offered with more than one engine option.
What it's used for
Factory manual for in-house farm and construction shop use. Straightforward, complete, and easy to follow. It contains the OEM information dealership service departments and parts counters use to diagnose problems, identify components, and perform maintenance or repairs correctly.
Service shops and owner/operators who repair their own equipment
Identifying correct parts and seeing how assemblies come apart and go back together
Keeping equipment running with less downtime
Factory manual, 799 pages
Quantity one is the manual described above.
Fast free USA shipping
Ships in 1 business day.
60-day returns
Free if the mistake is ours. A manual ordered in error must come back unopened in its shrink-wrap; you pay return shipping and a 20% restocking fee applies. Return policy
Binder not included
Manuals over about 300 pages may need a standard 3-ring binder, which you can buy locally to keep the pages organized for shop use.
Questions about model, serial number, engine coverage or contents? Contact us before purchasing and we'll help confirm it's the right manual. Please verify the manual type, machine model, serial number range and engine coverage before purchasing: manuals ordered in error carry a 20% restocking fee (return policy).