Clark PWC 30, PWT 7 Forklift Service Manual
333 pages · Publication SM-614
Added to your cart. View cart
- Models
- PWC 30, PWT 7
- Manual type
- Service Manual
- Pages
- 333
- Publication
- SM-614
- Condition
- Brand new
What's inside
From the manual's own table of contents: 11 sections, 172 entries. See sample pages (PDF, 271 KB)
GENERAL INFORMATION (GI)40 topics
- INTRODUCTION
- SPECIFICATIONS FOR PWT
- SPECIFICATIONS FOR PWC
- SERIAL NUMBER LOCATION CURRENT MODELS
- RECORD KEEPING
- TOOLS REQUIRED TO SERVICE THESE PRODUCTS
- TORQUE CHART
- CONVERSION FACTORS
- STANDARD SPEED AND SCR POTENTIOMETER ADJUSTMENTS
- GENERAL SERVICE GUIDE
- PWT MAINTENANCE SCHEDULE
- PWC FORK & LOAD LUBRICATION CHART
- PWT LUBRICATION CHART
- BATTERY CARE AND SERVICE
- Specific Gravity
- The Chemical Reaction
- Cleaning the Battery
- Adding Water
- The Hydrometer
- Battery Temperature
- Charging The Battery
- When To Charge
- BATTERY CONTROLLER
- Operation Adjustment and Maintenance
- The 933/3 Operation, Troubleshooting and Adjustment
- What Does It Tell The Driver?
- Reserve Warning Light
- Lift Lockout
- What Should The Driver Do?
- Adjustments
- Table of Pot Settings and Associated Voltages Per Cell
- What The Gage Measures
- Troubleshooting
- Adjustment Procedures
- Model 1142 Tester and Model 1141 FasTesT Accessory for Curtis 933/3 Battery Controller
- Features Of The
- Installation Of The
- Description Of Operation Of The
- PAINT & DECAL PWT
- PAINT & DECAL PWC
ELECTRICAL CONTROL (EC)66 topics
- BASIC ELECTRICAL THEORY
- Basic Electrical Terms
- Voltage
- Ampere
- Watt
- Ohms
- Polarity
- Direct Current (DC)
- Alternating Current (AC)
- Commonly Used Terms
- Fundamental Laws of Electricity
- TROUBLESHOOTING ELECTRICAL PROBLEMS
- The Logic of Electrical Troubleshooting
- Troubleshooting Procedure
- Troubleshoot With Your Senses
- A Troubleshooting Approach
- BASIC TEST (TOOLS) EQUIPMENT IN TROUBLESHOOTING
- FRONT PANEL DESCRIPTION
- DC VOLTAGE MEASUREMENTS 0.25 THROUGH 0-250V RANGE
- DIRECT CURRENT MEASUREMENT
- RESISTANCE MEASUREMENT OF SEMICONDUCTORS/DIODES/SCR’S
- DIGITAL DISPLAY
- ROTARY SWITCH
- JACKS
- MEASURING RESISTANCE
- TESTING DIODES
- MEASURING VOLTAGE
- SYMBOLS
- HANDYMAN COMPONENT TESTER INSTRUCTIONS
- TROUBLESHOOTING DO’S AND DON’TS
- ELECTRICAL SYMBOLS
- BASIC OPERATION FOR PWT RESISTOR CONTROL CONTACTOR
- Forward Travel
- Reverse Travel
- B.D.I. Speed Control Option
- Class 3 Resistor Units
- TROUBLESHOOTING PWT RESISTOR CONTROL
- NOTICE
- PARTS PAGE
- SERVICE GUIDE FOR PMC CONTROL SECOND EDITION 9301
- FEATURES OF CURTIS PMC SERIES TRANSISTORIZED MOTOR CONTROLLERS
- FUNCTIONAL OPERATION OF CONTROLLER
- MAINTENANCE AND ADJUSTMENT
- TROUBLESHOOTING
- TROUBLESHOOTING PWT CURTIS PMC CONTROL
- BASIC OPERATION FOR PWC CURTIS PMC
- TROUBLESHOOTING PWC CURTIS PMC CONTROL
- STANDARD SPEED AND SCR POTENTIOMETER ADJUSTMENTS
- STANDARD SPEED AND SCR POTENTIOMETER ADJUSTMENTS (EV-1, EV-100 AND CURTIS PMC)
- STANDARD SPEED AND SCR POTENTIOMETER ADJUSTMENTS
- EV-100 CONTACTOR AND MAINTENANCE
- BASIC OPERATION FOR PWT CURTIS PMC
- Forward Travel
- Reverse Travel
- Plugging (Controlled Reverse)
- Battery Discharge Speed Interrupt
- TROUBLESHOOTING PWT CURTIS PMC CONTROL
- BASIC OPERATION FOR PWC CURTIS PMC
- Forward Travel
- Reverse Travel
- TROUBLESHOOTING PWC CURTIS PMC CONTROL
- Main Accelerator Potentiometer Adjustment
- Adjustment Procedures
- PWT With Push Button Reverse
- PWT With Battery Discharge Speed Interrupt
- EV-100 CONTACTOR AND MAINTENANCE
HYDRAULIC SYSTEM (HD)18 topics
- BASIC OF HYDRAULIC
- What is Pressure
- Pressure On A Confined Fluid
- How To Determine Pressure
- One Of Pascal’s Laws
- Pascal’s Hydraulic Lever
- Multiplying Hydraulic Pressure
- Force Of An Area
- NPTF (National Pipe Tapered Fuel)
- ORS SAE 51453 O’Ring Face Seal
- SAE 5514 Straight Thread O’Ring Boss (ORB)
- BASIC HYDRAULIC OPERATION
- Lift Operation
- Lower Operation
- HYDRAULIC PUMP OPERATION AND DIAGNOSIS
- PUMP AND MOTOR DIAGNOSIS
- PUMP AND SERVICE MAINTENANCE
- SERVICE AND MAINTENANCE DC PUMP MOTORS
DRIVE ASSEMBLY (DA)19 topics
- TRANSMISSION DRIVE ASSEMBLY (GENERAL INFORMATION
- Basic Operation
- Gears, General Description
- Gear Ratio and Serial Number Location
- Steer Bearing
- Maintenance
- Planned Maintenance Schedule
- TRANSMISSION DRIVE ASSEMBLY (REPAIR AND SERVICE & INSTALLATION)
- Repair and Service
- TRANSMISSION DRIVE ASSEMBLY (UNITS BUILT FROM FEB. 1995)
- Dismantling Lower Transmission Section
- Assembly Lower Transmission Section
- G.E. DC DRIVE MOTORS
- Testing and Repair
- Planned Maintenance
- Commutator Check Chart
- DRIVE TIRE
- Tire Assembly Installation
- Tire Assembly Removal
BRAKE SYSTEM (BR)5 topics
- OPERATION & SERVICE PROCEDURE
- Service Procedure
- General Maintenance
- TILT STEERHEAD BRAKE ADJUSTMENT
- FIXED STEERHEAD BRAKE ADJUSTMENT
STEERING SYSTEM (ST)5 topics
- OPERATION
- Transmission
- PLANNED MAINTENANCE AND SERVICE
- Transmission
- Steerhead and Tiller Arm Maintenance
LOAD CARRIER (LC)8 topics
- GENERAL INTRODUCTION
- Load Carrying Device
- Load Wheel Operation
- PLANNED MAINTENANCE
- LOAD WHEELS
- Load Wheel Maintenance
- LOAD WHEEL REPLACEMENT
- FORK HEIGHT SETTING
Inside this manual
Real pages from this service manual (333 pages). Open the sample pages (PDF, 271 KB)
- Specifications, page 36: GENERAL INFORiMATION
- Troubleshooting, page 131: ELECTRIC CONTROL
- Diagram, page 196: ALWAYS SPECIFY MODEL Ah?D SERL4L NUMBER K=LEN ORDERING PARTS
This is a service manual
Here's how it compares to the other manual types.
Service manual
Factory repair procedures and technical information such as specifications, troubleshooting, and wiring and hydraulic diagrams, for the models and systems the manual covers. See What's inside for its topics.
Operator's manual
Safe operation, controls, maintenance schedules, lubrication points, inspections, and basic checks. Repair procedures are in the service manual.
Parts manual
Illustrated diagrams with factory part numbers for identifying components and ordering parts. Repair procedures are in the service manual.
Engine service manuals are sometimes sold separately, since certain machine models were offered with more than one engine option.
What it's used for
Factory manual for in-house farm and construction shop use. Straightforward, complete, and easy to follow. It contains the OEM information dealership service departments and parts counters use to diagnose problems, identify components, and perform maintenance or repairs correctly.
Service shops and owner/operators who repair their own equipment
Identifying correct parts and seeing how assemblies come apart and go back together
Keeping equipment running with less downtime
Factory manual, 333 pages
Quantity one is the manual described above.
Fast free USA shipping
Ships in 1 business day.
60-day returns
Free if the mistake is ours. A manual ordered in error must come back unopened in its shrink-wrap; you pay return shipping and a 20% restocking fee applies. Return policy
Binder not included
Manuals over about 300 pages may need a standard 3-ring binder, which you can buy locally to keep the pages organized for shop use.
Questions about model, serial number, engine coverage or contents? Contact us before purchasing and we'll help confirm it's the right manual. Please verify the manual type, machine model, serial number range and engine coverage before purchasing: manuals ordered in error carry a 20% restocking fee (return policy).