JCB 8052, 8060 Midi Excavator Service Manual
297 pages · Publication 9803-9290
Added to your cart. View cart
- Models
- 8052, 8060
- Manual type
- Service Manual
- Pages
- 297
- Publication
- 9803-9290
- Condition
- Brand new
What's inside
From the manual's own table of contents: 10 sections, 162 entries. See sample pages (PDF, 474 KB)
Section 154 topics
- Identification
- Storing your machine
- Preparation after Storage
- TOPS and FOGS
- Introduction
- Before entering the cab
- Machine walk round inspection
- Opening and closing the cab door
- Securing the door open
- Entering and exiting the cab
- Opening the windscreen
- Opening the side window
- Adjusting the seat
- Heater controls
- Fastening the seat belt
- Cab radio (optional)
- Switches and instruments
- Track controls
- Engine controls
- Switches
- Instruments
- Dozer controls
- Excavator controls
- Changing the Control Pattern (ISO/SAE)
- Slew cab
- Swing boom
- Raise / Lower boom
- Dipper
- Bucket
- Refuelling the machine
- Before starting the engine
- Starting the engine
- Jump Starting the Engine
- Cold climate warm up
- Operating in high / low temperatures
- Stopping and parking the machine
- Preparing for road / site travel
- Getting the machine moving
- Working with the dozer
- Working with the excavator
- Working on a slope
- Digging
- digging on the level
- Digging near walls
- Lifting Regulations and Safe Working Loads
- Using the attachments and site safety
- Moving a disabled machine
- Transporting the machine
- Preparing the transporter for loading
- Loading onto the transporter
- Securing the machine
- Unloading the machine
- Service Tools
- Sealing and Retaining Compounds
Section 24 topics
- Safety Notices
- General Safety
- Operating Safety
- Maintenance Safety
Section 331 topics
- Fluids, Lubricants, Capacities and Specifications
- Engine Lubrication Chart
- Lubricants - Health and Safety
- Torque Settings
- Hydraulic Fittings and Torque Settings
- Fuel Systems
- Bleeding the fuel system - 8052
- Bleeding the fuel system - 8060
- Draining the Filter Element - 8052
- Changing the Filter Element - 8052
- Draining the Sediment Bowl
- Changing the Filter Element - 8060
- Cleaning Lift Pump Strainer - 8060
- Service Schedules
- Greasing
- Greasing (every 250 hours) Slew Ring Bearing
- Greasing (every 1000 hours) Slew Ring Gear Teeth
- Checking and Adjusting the Fluid Level
- Replacing the Hydraulic Filter
- Checking the Ram Piston Rods
- Track Gearbox
- Changing the Element
- Checking the Oil Level
- Changing the Oil and Filter
- Coolant Mixtures
- Checking the Coolant Level
- Changing the Coolant
- Adjusting the Fan Belt
- Warning Symbols
- First Aid - Electrolyte
- Checking the Electrolyte Level
Section A21 topics
- Available Attactments
- Selection
- Removal (Non Quickhitch Models)
- Installing a Bucket (Non Quickhitch Models)
- Replacing Bucket Teeth
- Quickhitch
- Installing
- Removal
- Installing Excavator Quickhitch Attachments
- Removing Excavator Quickhitch Attachments
- Hydraulic Attachment Circuits
- Single Acting Hydraulic Circuit
- Fitting Instrauctions (980/88808)
- Double Acting Hydraulic Circuit
- Fitting Instructions (980/88809)
- Hydraulic Breakers
- Removing a Quickhitch Rockbreaker
- Installing a Quickhitch Rockbreaker
- Making the Machine Ready
- Assembly/Installation
- Using Hand Held Tools
Body & Framework5 topics
- General Description
- Removal and Replacement
- Removal & Replacement
- Seat Base Installation
- Setting up
Electrics15 topics
- Technical Data
- Battery
- Fan Belt
- Starter Motor
- Mounting
- Bulb Change
- Schematic Diagrams
- Wiring Harness Repair
- Wire Identification
- Harness Locations and Connections - 8052
- Main Harness
- Cab Harness
- Canopy Harness
- Optional Working Light Harness
- Boom Working Light Harness
Section D3 topics
- Description and Operation
- Port Identification
- Inspection
Hydraulics17 topics
- Hydraulic Circuit (Schematic)
- Main Circuit
- Servo Circuit
- Description
- Load Sensing - Maximum Flow
- Load Sensing - Standby
- Load Sensing - Maximum Pressure (No Flow)
- Initial Build Performance Checks
- Pump Drive - Removal and Replacement
- Renewing Pump Drive Seal
- Pump - Dismantling and Assembly
- Dismantling and Assembly
- Cross Line Relief Valve
- Testing Compensator Shuttle Signal Network
- Servo Hand Controllers
- Pressure Maintenance Valve
- Slew Cross Line Relief Valve
Track & Running Gear2 topics
- Clean and Inspection
- Converting Steel - Rubber/Rubber - Steel
Inside this manual
Real pages from this service manual (297 pages). Open the sample pages (PDF, 472 KB)
- Diagram, page 138: Section C
- Specifications, page 186: *Technical Data - 8060
- Repair procedure, page 234: Track Motor - 8060
- Color page, page 209: Section E
- Color page, page 237: Section E
- Foldout diagram, page 167: Harness Data
This is a service manual
Here's how it compares to the other manual types.
Service manual
Factory repair procedures and technical information such as specifications, troubleshooting, and wiring and hydraulic diagrams, for the models and systems the manual covers. See What's inside for its topics.
Operator's manual
Safe operation, controls, maintenance schedules, lubrication points, inspections, and basic checks. Repair procedures are in the service manual.
Parts manual
Illustrated diagrams with factory part numbers for identifying components and ordering parts. Repair procedures are in the service manual.
Engine service manuals are sometimes sold separately, since certain machine models were offered with more than one engine option.
What it's used for
Factory manual for in-house farm and construction shop use. Straightforward, complete, and easy to follow. It contains the OEM information dealership service departments and parts counters use to diagnose problems, identify components, and perform maintenance or repairs correctly.
Service shops and owner/operators who repair their own equipment
Identifying correct parts and seeing how assemblies come apart and go back together
Keeping equipment running with less downtime
Factory manual, 297 pages
Quantity one is the manual described above.
Fast free USA shipping
Ships in 1 business day.
60-day returns
Free if the mistake is ours. A manual ordered in error must come back unopened in its shrink-wrap; you pay return shipping and a 20% restocking fee applies. Return policy
Questions about model, serial number, engine coverage or contents? Contact us before purchasing and we'll help confirm it's the right manual. Please verify the manual type, machine model, serial number range and engine coverage before purchasing: manuals ordered in error carry a 20% restocking fee (return policy).