JLG 100HX, 100HX+10, 110HX Boom Lift Service Manual
162 pages · Publication 3120636
Added to your cart. View cart
What's inside
From the manual's own table of contents: 183 sections, 232 entries. See sample pages (PDF, 534 KB)
Maintenance2 topics
- Capacities
- Component Data
Hydraulic Filter - Inline1 topic
- Performance Data
Show all 183 sections
Maximum Tire Loads2 topics
- Torque Requirements
- Lubrication
Lubrication Specifications1 topic
- Pressure Settings
Extend-A-Reach Valve2 topics
- Cylinder Specifications
- Boom Tape
With 4620038 Turntable4 topics
- Major Component Weights
- Serial Number Locations
- General
- Servicing and Maintenance Guidelines
Lubrication and Servicing1 topic
- Lubrication Information
Changing Hydraulic Oil2 topics
- Cylinders - Theory of Operation
- Valves - Theory of Operation
Crossover Relief Valves1 topic
- Boom Chains
Inspection Procedure2 topics
- Wear Pads
- Drift Test
Lift Cylinder1 topic
- Cylinder Checking Procedures
Cylinders w/Dual Counterbalance Valve1 topic
- Cylinder Removal and Installation
Master Level Cylinder Installation1 topic
- Cylinder Repair
Cleaning and Inspection1 topic
- SECTION NO. TITLE PAGE NO. Boom Maintenance
Installation1 topic
- Tilt Alarm Switch Leveling
Voltmeter Adjustment1 topic
- Limit Switch Adjustments
Horizontal Cut-Out Switch2 topics
- Throttle Checks and Adjustments - Deutz F4l-912 Engine
- Throttle Checks and Precision Governor Adjustments - Ford Engine
Carburetor and Governor Adjustments1 topic
- Pressure Setting Procedures
Extend-A-Reach Valve (If Equipped)1 topic
- Swing Bearing
Swing Bearing Torque Values9 topics
- Drive Torque Hub
- Swing Torque hub
- Swing Brake - Ausco - Machines Built To 1992
- Swing Brake - Mico - Machines Built To 1992
- Swing Brake - Machines Built 1992 To Present
- Drive Brake - Ausco - Machines Built Prior To March 1992
- Drive Brake - Mico - Machines Built March 1992 TO S/N 33476
- SECTION NO. TITLE PAGE NO. Drive Brake - Mico - Machines Built S/N 33476 To Present
- Free Wheeling Option
To Engage Drive Motors and Brakes (Normal Operation)1 topic
- OEM Controllers
LO RANGE Adjustment (CREEP)2 topics
- Boom Marking Tape Installation
- Boom Length/angle Sensor Adjustment Procedures
3rd Generation Radius Cards1 topic
- Load Management System
Load Management System Daily Check3 topics
- Load Management System Adjustment
- Turntable Springs
- Pump Coupling Conversion Procedures
Hayes Coupling5 topics
- Hydraulic Component Start-Up Procedures and Recommendations
- Platform Rotator Brake
- Preventive Maintenance and Inspection Schedule
- Troubleshooting
- Hydraulic Circuit Checks
Inside this manual
Real pages from this service manual (162 pages). Open the sample pages (PDF, 534 KB)
- Specifications, page 21: SECTION 1 - SPECIFICATIONS
- Troubleshooting, page 121: SECTION 3. TROUBLESHOOTING
- Diagram, page 157: Figure 3-18. Wiring Diagram - 100HX+10 w/Ford Engine (Sheet 2 of 4)
Other manuals for this machine
Save 10% on 2 manuals, 15% on 3 or more. Other manuals are listed below. Editions cover different serial number ranges: check the serial coverage and tick only the ones that match your machine.
Added to your cart. View cart
This is a service manual
Here's how it compares to the other manual types.
Service manual
Factory repair procedures and technical information such as specifications, troubleshooting, and wiring and hydraulic diagrams, for the models and systems the manual covers. See What's inside for its topics.
Operator's manual
Safe operation, controls, maintenance schedules, lubrication points, inspections, and basic checks. Repair procedures are in the service manual.
Parts manual
Illustrated diagrams with factory part numbers for identifying components and ordering parts. Repair procedures are in the service manual.
Engine service manuals are sometimes sold separately, since certain machine models were offered with more than one engine option.
What it's used for
Factory manual for in-house farm and construction shop use. Straightforward, complete, and easy to follow. It contains the OEM information dealership service departments and parts counters use to diagnose problems, identify components, and perform maintenance or repairs correctly.
Service shops and owner/operators who repair their own equipment
Identifying correct parts and seeing how assemblies come apart and go back together
Keeping equipment running with less downtime
Factory manual, 162 pages
Quantity one is the manual described above.
Fast free USA shipping
Ships in 1 business day.
60-day returns
Free if the mistake is ours. A manual ordered in error must come back unopened in its shrink-wrap; you pay return shipping and a 20% restocking fee applies. Return policy
Other editions and similar models
Questions about model, serial number, engine coverage or contents? Contact us before purchasing and we'll help confirm it's the right manual. Please verify the manual type, machine model, serial number range and engine coverage before purchasing: manuals ordered in error carry a 20% restocking fee (return policy).