Komatsu D375A-5E0 Bulldozer Operation & Maintenance Manual
344 pages · Publication TEN00258-02
Added to your cart. View cart
- Models
- D375A-5E0
- Serial coverage
- 50065 and up
- Manual type
- Operation & Maintenance Manual
- Pages
- 344
- Publication
- TEN00258-02
- Condition
- Brand new
What's inside
From the manual's own table of contents: 99 topics. See sample pages (PDF, 380 KB)
- NECESSARY INFORMATION
- PRODUCT IDENTIFICATION NUMBER (PIN), MACHINE SERIAL NO. PLATE
- EPA REGULATIONS, ENGINE NUMBER PLATE
- BLADE SERIAL NO. PLATE POSITION
- RIPPER SERIAL NO. PLATE POSITION
- ROPS, FOPS NO. PLATE POSITION
- POSITION OF SERVICE METER
- TABLE TO ENTER SERIAL NO. AND DISTRIBUTOR
- PRECAUTIONS FOR OPERATION
- BEFORE STARTING ENGINE
- OPERATION
- TRANSPORTATION
- BATTERY
- TOWING
- PRECAUTIONS FOR MAINTENANCE
- SWITCHES
- CONTROL LEVERS, PEDALS
- DUST INDICATOR
- POWER SOURCE
- FUSE BOX
- DOOR OPEN LOCK
- SASH GLASS INTERMEDIATE LOCK
- CAP WITH LOCK
- DOOR POCKET
Show all 99 topics
- ASHTRAY
- TOOL BOX
- CAR STEREO, HANDLING
- AIR CONDITIONER, HANDLING
- CHECK BEFORE STARTING ENGINE, ADJUST
- STARTING ENGINE
- OPERATIONS AND CHECKS AFTER STARTING ENGINE
- STOPPING ENGINE
- MOVING MACHINE
- STOPPING MACHINE
- SHIFTING GEAR
- SHIFTING BETWEEN FORWARD AND REVERSE
- STEERING MACHINE
- PARKING MACHINE
- CHECK AFTER STOPPING ENGINE
- CHECK AFTER FINISHING WORK
- LOCKING
- WORK POSSIBLE USING BULLDOZER
- EFFECTIVE USE OF MODE SELECTION SYSTEM
- RIPPER OPERATION
- OPERATING METHOD FOR RIPPING OPERATIONS
- ADJUSTING POSTURE OF WORK EQUIPMENT
- TIPS FOR LONGER UNDERCARRIAGE LIFE
- TRANSPORTATION PROCEDURE
- LOADING, UNLOADING WORK
- METHOD OF LIFTING MACHINE
- TRAVELING ON ROADS
- REMOVAL OF CAB
- INSTALLATION OF CAB
- INSTALLATION OF ROPS
- COLD WEATHER OPERATION
- PRECAUTIONS FOR LOW TEMPERATURE
- AFTER COMPLETION OF WORK
- AFTER COLD WEATHER
- LONG-TERM STORAGE
- BEFORE STORAGE
- DURING STORAGE
- AFTER STORAGE
- STARTING MACHINE AFTER LONG-TERM STORAGE
- TROUBLESHOOTING
- AFTER RUNNING OUT OF FUEL
- METHOD OF TOWING MACHINE
- IF BATTERY IS DISCHARGED
- OTHER TROUBLE
- WHEN MODE SELECTION SYSTEM FLASHES
- WEAR PARTS
- WEAR PARTS LIST
- RECOMMENDED FUEL, COOLANT, AND LUBRICANT
- OTHER THAN KOMATSU GENUINE OIL
- STANDARD TIGHTENING TORQUES FOR BOLTS AND NUTS
- TORQUE LIST
- PERIODIC REPLACEMENT OF SAFETY CRITICAL PARTS
- SAFETY CRITICAL PARTS
- MAINTENANCE SCHEDULE CHART
- SERVICE PROCEDURE
- INITIAL 250 HOURS SERVICE (ONLY AFTER THE FIRST 250 HOURS)
- WHEN REQUIRED
- CHECK BEFORE STARTING
- EVERY 250 HOURS SERVICE
- EVERY 500 HOURS SERVICE
- EVERY 1000 HOURS SERVICE
- EVERY 2000 HOURS SERVICE
- EVERY 4000 HOURS SERVICE
- EVERY 8000 HOURS SERVICE
- LEVELING (SPREADING) OPERATION
- DITCHING OPERATION
- BOULDER RAISING OPERATION
- SIDE-CUTTING OPERATIONS
- HORIZONTAL DOZING OPERATIONS FROM SIDE SLOPE (ROUGH GROUND)
- SHOE SLIP CONTROL
- MODE SELECTION SWITCH PANEL (SHOE SLIP CONTROL)
- IF MODE SELECTION SYSTEM FLASHES
- HANDLING MACHINES EQUIPPED WITH VHMS
- VHMS INSTALLED, COMMUNICATIONS TERMINAL NOT INSTALLED
- VHMS AND COMMUNICATIONS TERMINAL INSTALLED
Inside this manual
Real pages from this operation & maintenance manual (344 pages). Open the sample pages (PDF, 380 KB)
- Controls and operation, page 121: EXPLANATION OF COMPONENTS
- Specifications, page 156: 7. Check that engine pre-heating pilot lamp (3) on the monitor
- Maintenance, page 246: SERVICE PROCEDURE
Other manuals for this machine
Save 10% on 2 manuals, 15% on 3 or more. Other manuals for the D375A-5E0 are listed below. Editions cover different serial number ranges: check the serial coverage and tick only the ones that match your machine.
Added to your cart. View cart
This is an operator's manual
Here's how it compares to the other manual types.
Service manual
Factory repair procedures and technical information such as specifications, troubleshooting, and wiring and hydraulic diagrams, for the models and systems the manual covers. See What's inside for its topics.
Operator's manual
Safe operation, controls, maintenance schedules, lubrication points, inspections, and basic checks. Repair procedures are in the service manual.
Parts manual
Illustrated diagrams with factory part numbers for identifying components and ordering parts. Repair procedures are in the service manual.
What it's used for
Factory manual for in-house farm and construction shop use. Straightforward, complete, and easy to follow. It contains the OEM information dealership service departments and parts counters use to diagnose problems, identify components, and perform maintenance or repairs correctly.
Service shops and owner/operators who repair their own equipment
Identifying correct parts and seeing how assemblies come apart and go back together
Keeping equipment running with less downtime
Factory manual, 344 pages
Quantity one is the manual described above.
Fast free USA shipping
Ships in 1 business day.
60-day returns
Free if the mistake is ours. A manual ordered in error must come back unopened in its shrink-wrap; you pay return shipping and a 20% restocking fee applies. Return policy
Binder not included
Manuals over about 300 pages may need a standard 3-ring binder, which you can buy locally to keep the pages organized for shop use.
Other editions and similar models
Questions about model, serial number, engine coverage or contents? Contact us before purchasing and we'll help confirm it's the right manual. Please verify the manual type, machine model, serial number range and engine coverage before purchasing: manuals ordered in error carry a 20% restocking fee (return policy).