New Holland Cursor 11 Tier 4B, Stage IV F3GFE613A*B001, F3GFE613B*B001 Engine Service Manual
337 pages · Publication 47608463
Added to your cart. View cart
- Models
- Cursor 11 Tier 4B, Stage IV F3GFE613A*B001, F3GFE613B*B001
- Manual type
- Service Manual
- Pages
- 337
- Publication
- 47608463
- Condition
- Brand new
What's inside
From the manual's own table of contents: 98 topics. See sample pages (PDF, 298 KB)
- Engine
- Engine and crankcase
- Cylinder heads
- Pan and covers
- Crankshaft and flywheel
- Connecting rods and pistons
- Valve drive and gears
- Balancer and damper
- Pump drives
- Fuel filters
- Fuel injection system
- Turbocharger and lines
- Intake and exhaust manifolds and muffler
- Engine lubrication system
- Engine cooling system
- Oil cooler and lines
- Fan and drive
- Selective Catalytic Reduction (SCR) exhaust treatment
- Electrical systems
- Fuel injection system
- Engine cooling system
- Engine intake and exhaust system
- Engine control system
- Cold start aid
Show all 98 topics
- Selective Catalytic Reduction (SCR) electrical system
- Foreword - Important notice regarding equipment servicing
- Safety rules
- Safety rules - Ecology and the environment
- Torque - Minimum tightening torques for normal assembly
- Basic instructions - Shop and assembly
- Technical Data
- Overview
- Service instruction - Finding Top Dead Center (TDC)
- Liner - Remove
- Liner - Install
- Liner - Measure – Protrusion
- Under block - Remove
- Under block - Install
- General specification
- Remove
- Install
- Disassemble
- Check
- Assemble
- Remove – Outlet to cabin heater
- Install – Outlet to cabin heater
- Cleaning
- Measure
- Replace
- Front seal - Remove
- Front seal - Install
- Rear seal - Remove
- Rear seal - Install
- Journal - Clearance
- Connecting rod - Measure
- Pin - Measure
- Ring - Measure
- Upper idler gear - General specification
- Lower idler gear - General specification
- Exploded view
- Adjust
- Timing check
- Timing adjust
- Upper idler gear - Remove
- Upper idler gear - Install
- General specification – Pressure relief valve
- Dynamic description
- Sectional view
- Relief valve - Overview
- Configure - Reset ECU data
- Relief valve - Configure - Reset ECU data
- Relief valve - Remove
- Relief valve - Inspect
- Relief valve - Install
- General specification – Overpressure valve
- General specification – Regulator valve
- Overview – Overpressure valve
- Overview - Regulator valve
- Remove – Regulator valve
- Install – Regulator valve
- Spray nozzle - Remove
- Spray nozzle - Install
- Water manifold - Exploded view
- Water manifold - Remove
- Water manifold - Install
- Remove – Air conditioner
- Install – Air conditioner
- Service instruction - SCR fault repair verification test
- Configure - Engine restart counter reset
- Inspect
- Flywheel - Overview
- Camshaft - Overview
- Flywheel - Remove
- Flywheel - Install
- Camshaft - Remove
- Camshaft - Install
- Configure - Reset ECU data (Upstream sensor)
- Configure - Reset ECU data (Downstream sensor)
Inside this manual
Real pages from this service manual (337 pages). Open the sample pages (PDF, 298 KB)
- Specifications, page 21: Engine - Engine and crankcase
- Repair procedure, page 61: Engine - Pan and covers
- Color page, page 204: Engine - Engine lubrication system
This is a service manual
Here's how it compares to the other manual types.
Service manual
Factory repair procedures and technical information such as specifications, troubleshooting, and wiring and hydraulic diagrams, for the models and systems the manual covers. See What's inside for its topics.
Operator's manual
Safe operation, controls, maintenance schedules, lubrication points, inspections, and basic checks. Repair procedures are in the service manual.
Parts manual
Illustrated diagrams with factory part numbers for identifying components and ordering parts. Repair procedures are in the service manual.
Engine service manuals are sometimes sold separately, since certain machine models were offered with more than one engine option.
What it's used for
Factory manual for in-house farm and construction shop use. Straightforward, complete, and easy to follow. It contains the OEM information dealership service departments and parts counters use to diagnose problems, identify components, and perform maintenance or repairs correctly.
Service shops and owner/operators who repair their own equipment
Identifying correct parts and seeing how assemblies come apart and go back together
Keeping equipment running with less downtime
Factory manual, 337 pages
Quantity one is the manual described above.
Fast free USA shipping
Ships in 1 business day.
60-day returns
Free if the mistake is ours. A manual ordered in error must come back unopened in its shrink-wrap; you pay return shipping and a 20% restocking fee applies. Return policy
Binder not included
Manuals over about 300 pages may need a standard 3-ring binder, which you can buy locally to keep the pages organized for shop use.
Other editions and similar models
Questions about model, serial number, engine coverage or contents? Contact us before purchasing and we'll help confirm it's the right manual. Please verify the manual type, machine model, serial number range and engine coverage before purchasing: manuals ordered in error carry a 20% restocking fee (return policy).