MidWestTechService, Parts and Operator's Manuals, in stock and ready to ship!
Fast free USA shippingShips in 1 business daySave 10% on 2 manuals, 15% on 3+

New Holland HW345, HW365 Windrower Service Manual

1,573 pages · Publication 87576216

$159.95
Fast free USA shippingShips in 1 business daySave 10% on 2 manuals, 15% on 3 or morePay by credit or debit card or with PayPal. No PayPal account needed.
Models
HW345, HW365
Manual type
Service Manual
Pages
1,573
Publication
87576216
Condition
Brand new
New Holland HW345, HW365 Windrower Service Manual, publication 87576216

What's inside

From the manual's own table of contents: 363 sections, 700 entries. See sample pages (PDF, 670 KB)

SECTION 00 - GENERAL INFORMATION
SECTION 10 - ENGINE
SECTION 25 - FRONT MECHANICAL DRIVE
SECTION 29 - HYDROSTATIC TRANSMISSION
SECTION 33 - BRAKES AND CONTROLS
SECTION 35 - HYDRAULIC SYSTEMS
SECTION 44 - REAR AXLE
SECTION 50 - CLIMATE CONTROL
SECTION 55 - ELECTRICAL SYSTEMS
SECTION 58 - HEADER ATTACHMENTS
SECTION 88 - OPTIONAL EQUIPMENT
SECTION 90 - PLATFORM, CAB AND DECALS
00 000 Precautionary Statements
Safety
General Safety Information
Introduction
About Improvements
Product Identification Numbers (PIN)
Engine PIN Number
Company Policy
Parts and Specification
Lubrication
Recommended Lubricants and Coolants
Sealants
Show all 363 sections
Minimum Hardware Tightening Torques
Installation of Adjustable Fittings in Straight Thread O ring Bosses
Standard Torque Data for Hydraulic Tubes and Fittings
Pipe Thread Fitting Torque
Installation of ORFS (O ring Flat Faced) Fittings
Specifications
Torque Values
Special Tools
Troubleshooting
Description of Operation
Cylinder Block Assembly
Cylinder Head Assembly
Camshaft Assembly
Crankshaft Assembly
Connecting Rods
Pistons
Manifolds
Timing Gears
Lubrication System
Crankcase Breather
Overhaul
Engine - Complete1 topic
  • Removal
Flywheel1 topic
  • Installation
Engine Overhaul -- Introduction
Timing Check
Component Overhaul
Cylinder Head, Valves, and Related Parts9 topics
  • Cylinder Head Removal
  • Cylinder Head Disassembly
  • Inspection and Repair, Cylinder Head
  • Valve Inserts
  • Valve Guides
  • Valve Springs
  • Rocker Shaft Inspection and Reassembly
  • Cylinder Head Reassembly
  • Hydraulic Tappets
Engine Front Cover and Timing Gears2 topics
  • Timing Gears Checking and Removal
  • Inspection and Repair of Gears
Oil Pan1 topic
  • Inspection and Repair
Rear Cover Plate
Oil Pump1 topic
  • Disassembly
Oil Pressure Relief Valve
Camshaft
Camshaft Bearings
Connecting Rod Bush Replacement
Cylinder Block Overhaul
Cylinder Bore3 topics
  • Specifications
  • Sleeving -- Boring and Honing
  • Reassembly
Installing Piston Assembly Into Block
Crankshaft
Front Seal
Engine Compression Test3 topics
  • Test Procedure
  • Test Readings
  • Test Conclusion
Fuel System Torque Chart
Fuel System1 topic
  • Fuel Shut Off (Injection Pump)
6-cylinder Fuel and Induction System
Bosch VP Distributor -- Type Fuel Injection System
Fuel Tank
Electric Lift Pump
Fuel Filters4 topics
  • Testing
  • Bleeding Air From Filter
  • Injection System Bleeding
  • Air Leakage Test
Fuel Injection Pump
Fuel Injectors
Cold Start Assist (Option)
Plumbing
Fuel Tanks1 topic
  • Connecting Fuel Tanks
Electronically Controlled Fuel Injection Pump
Bosch VP Fuel Injection Pump -- (Electronically Controlled)1 topic
  • Inspection
Injection Pump Timing Check2 topics
  • Testing and Overhaul
  • Nozzle Opening Pressure
Air Cleaner
General Torques
Description of Operation -- Air Cleaner
Inner Element
Troubleshooting -- Air Cleaner
Overhaul --Air Cleaner3 topics
  • Clean or Replace Primary (Outer) Air Filter
  • Replace the Secondary (Inner) Air Filter
  • Air Intake Hoses
Description of Operation -- Turbocharger
Troubleshooting -- Turbocharger
Overhaul -- Turbocharger4 topics
  • Cleaning
  • Center Shaft Radial Check
  • Axial Clearance Check
  • Leak Diagnosis
Cooling System (CNH 7.5 Liter Engine)
Tightening Torques
Thermostat
Water Pump
Drive Belt
Cooling Capacities
Coolant Flow
Cooling Fluid
Radiator
Temperature Warning Sender
Belt Tensioner
Idler Pulley2 topics
  • Reassembly: 6-cylinder
  • Installation: 6-cylinder
Engine Oil Consumption
Evaluating Oil Consumption
Front Mechanical Drive
Planetary Gearbox Drive1 topic
  • Assembly
Labor Guide
Hydrostatic Transmission Identification
Torque Specifications
Torque Chart
Motor Area
Pumps
High Pressure Relief Valves
Check Valves
Charge Pump
Charge Relief Valve (Pump)
Header Lift Pump
Motors1 topic
  • Variable Displacement Motor
Reservoir
Oil Flow2 topics
  • Neutral
  • Forward/Reverse
Hydraulic System Diagram
Solenoid Valve3 topics
  • Low-Range Operation
  • High-Range Operation
  • Cooling Circuit
Relief Valve1 topic
  • Operation
Linkage
Sauer-Danfoss Authorized Service Centers -- North America
Excessive Noise
Overheating Transmissions1 topic
  • Loss of Propulsion
Control Linkage Inspection
High-Pressure Relief Valve Check
Charge Pump Relief Valve
Check Valve
Pressure Testing2 topics
  • Port Locations
  • Charge Pressure
Charge Pressure System Test2 topics
  • Tandem Pump Charge Pressure Test
  • Complete Charge System Test
High Pressure Relief Valve Test4 topics
  • Case Pressure Test (Pump)
  • Case Pressure Test (Motor)
  • Suction Test
  • Case Flow Test
Ground Speed Circuit1 topic
  • Troubleshooting
Troubleshooting Charts4 topics
  • Windrower Will Not Shift into High Range
  • Windrower Will Not Shift into Low Range
  • Charge Pump
  • Hydrostatic System
Explanation of Terms Used in Failure Analysis5 topics
  • Lack of Lubrication
  • Operating at Excessive Temperature Levels
  • Use of Improper Fluid
  • Cavitation
  • Overspeeding of the Unit
Parts Worn or Scored From Contamination2 topics
  • Abrasive Contaminants
  • Plates Scored from Water in Oil (Non-Particle Contaminants)
Minor Repairs
Tandem Pump11 topics
  • Rear Half Pump Breakdown
  • Front Half Pump Breakdown
  • Shaft Seal Replacement
  • Charge Pump Removal
  • Charge Pump Inspection
  • Charge Pump Assembly
  • O ring Seals
  • Trunnion Seal (Control Shaft Side)
  • Trunnion Cover (Plain)
  • Tandem Pump Removal
  • Tandem Pump Installation
Ground Drive Motor
Start-Up
Maintenance
Worm Shaft
Theory of Operation
Pintle Arm Rotary Potentiometer (R21)
Propulsion Rotary Position Sensor (R23)
MFH Rotary Position Sensor (R18)
Neutral Adjustment
Active Calibrations
Dealer Setup Menu Navigation
MFH Calibration
Brake Assembly
Rotating, Stationary, and Primary Disc Assembly
Brake Bleeding Procedure
System Component Locations
Reading Diagram Symbols
Theory of Operation -- Ground Drive2 topics
  • Ground Drive
  • Circuit Diagrams
Service Techniques5 topics
  • General
  • Oil Level
  • Hoses and Tubes
  • O Ring Flat Face Seal Fittings
  • O Ring Flat Face Seal Fitting Torque Values
Theory of Operation -- Header Drive2 topics
  • Header Drive
  • Electronic Displacement Control (EDC)
Theory of Operation -- Header Lift System5 topics
  • Header Lift System
  • Neutral State
  • Header Lift
  • Accumulator Charge
  • Header Lower/Flotation
Theory of Operation -- Floatation/Accumulators2 topics
  • Floatation/Accumulators
  • Increase/Decrease Floatation
Theory of Operation -- Header Tilt System1 topic
  • Header Tilt System
Theory of Operation -- Auxiliary Hydraulic Pump1 topic
  • Auxiliary Hydraulic Pump (optional)
Independent Control Valve (ICV) Manifold (HW345/365)9 topics
  • Service Parts
  • Valve Identification Codes
  • Component Identification and Location
  • Right-Hand (RH) View
  • Plan View
  • Front View
  • Rear View
  • Bottom View
  • Left-hand (LH) View (Hidden Against Mounting Plate)
Energized Solenoid Chart
Zero-Leak Plugs3 topics
  • Install
  • Plug Torque Requirements
  • Zero-Leak Plug to SAE J514 ORB Plug Cross Reference
Auxiliary Control Valve (Speed Control) Manifold (HW345/365)
Auxiliary Control Valve
Theory of Operation -- Cartridge Valves7 topics
  • Cartridge Valves (Solenoid-operated)
  • Two-way Two-position (Normally Closed) Poppet Valves
  • Three-way Two-position Spool Valve
  • Two-way Two-position (Normally Open) Poppet Valve
  • (Normally Open) Pressure Reducing/Relieving Valves
  • (Normally Open) Solenoid-operated Relief Valves
  • (Normally Closed) Solenoid-operated Proportional Flow Control
Main Manifold Cartridge Torque Requirement1 topic
  • Replacement
Solenoid Coils
Cartridge Valves (Non-solenoid-operated)4 topics
  • Direct-acting Flow Control Needle Valve
  • Pilot-operated Relief Valve
  • Differential-Pressure-Sensing Valve
  • Adjustment
Header Drive Pump10 topics
  • Removing the Multifunction Valve Cartridge
  • Installing the Multifunction Valve Cartridge
  • Removing the Charge Pressure Relief Valve
  • Installing the Charge Pressure Relief Valve
  • Diagnosing the EDC and Pilot Control Valve Assembly
  • Dealer Setup Menu Navigation
  • Removing the EDC and PCP Valve Assembly
  • Installing the EDC and PCP Valve Assembly
  • Removing the Charge Cooling Circuit Manifold
  • Installing the Remote Charge Cooling Circuit Manifold
Major Components2 topics
  • Removing the Pump Shaft Seal
  • Installing the Pump Shaft Seal
Start-up Procedure
Pressure Checks -- Header Drive System11 topics
  • Test Equipment
  • Pressure Readings
  • Charge Pressure -- Header Drive Pump
  • Charge Pressure -- Header Drive Motor
  • Pump Gauge Information
  • Case Pressure
  • High Pressure
  • Motor Gauge Information
  • Inlet Vacuum
  • Case Drain Flow
  • Cooling Circuit Bypass Pressure
Troubleshooting -- Header Drive System
General5 topics
  • Reduced System Pressure
  • Reduced Hydraulic Flow
  • Excessive Noise
  • Overheating
  • Power Loss
Parts Evaluation4 topics
  • Discoloration
  • Scratches or Grooves
  • Rework
  • Repeat Failures
Hydraulic Oil Temperatures
Header Drive System1 topic
  • Further Troubleshooting Tips
Header Drive Motor
Adjustments2 topics
  • Header Drive Pump
  • Neutral Adjustment
Diagnosing the Multifunction Valves
Diagnosing the Charge Pressure Relief Valve
Header Drive Motors
Header Drive Speed Sensor Gap
Sauer-Danfoss Authorized Service Centers - North America
Adjustment Instructions
Six Cylinder -- RH Header Lift Relief Valve (L-03) Pressure Adjustment
Six Cylinder -- LH Header Lift Relief Valve (L--04) Pressure Adjustment
Accumulators -- Header Lift
Accumulator -- Surge Suppression
Hydraulic Accumulator Breakdown
Checking Pre-Charge
Pre-Charging Procedure
Lift Cylinders
Tilt Cylinder
Auxiliary Engine Mounted Hydraulic Pump (optional)
Hydraulic Reservoir Replacement1 topic
  • Tank Preparation (Plastic Tanks only)
44 000 Introduction
Overview
Extensions and Axle Tube
Wheel Width
Extension Widths (Spindle to Spindle)
Wheel, Axle Shaft and Hub
Axle Support Fork
Extension
Axle Tube and Pivot Pin
Extensions and Axle Tubes
Air Spring
Axle Tubes and Pivot Pins
The Basics of Refrigeration
Air Conditioning Process
R134a Refrigerant Information
Refrigerant Ingredients2 topics
  • Lubricants
  • Refrigerant (R134a)
Cab Air Flow
System Components
Compressor Pump
Compressor Clutch (L-27)
External Cab Filter1 topic
  • Removal/Replacement
Recirculation Filter1 topic
  • Cleaning With Air
Condenser
Receiver/Drier
Expansion Valve3 topics
  • Description
  • Valve Components
  • Port Identification
Evaporator
Blower Fan
Description of Operation -- Climate Controls
Control Panel – Manual Temperature Control (A-05)2 topics
  • Blower Fan Switch
  • Temperature Control Switch
Control Panel – (ATC) Automatic Temperature Control (If Equipped)
Control Operation Specifications1 topic
  • ATC Operator Controls
Compressor Protection Switches2 topics
  • High-pressure Cutout Switch (S-40)
  • Low-pressure Cutout Switch (S-69)
Troubleshooting and Servicing Air Conditioning System
General Safety and Service Precautions
Cleanliness
Preliminary Troubleshooting and Testing1 topic
  • Operational Checks
Troubleshooting -- Fault Code Chart
Display Fault Codes
Advanced Diagnostics
Diagnosis Charts – Air Conditioning System2 topics
  • Test Procedure: Stabilizing the System
  • Test Ports
Pressure/Temperature Relationships2 topics
  • Leak Testing
  • Refilling
Contaminants
Refrigerant Extraction and Recycling Equipment3 topics
  • Using Extraction Equipment
  • Using Recycled Equipment
  • Recycling Vs. Reclaiming
Containment of Air Conditioning Refrigerants7 topics
  • Recovery
  • Flushing
  • Recharging/Refilling
  • Using a Manifold Gauge Set
  • Checking Refrigerant for Excess Air
  • Containers for Storing Recycled Refrigerant
  • Disposal of Empty or Near-empty Disposable Containers
Applicable SAE Standards
Manifold Gauge Readings and Interpretations
Performance Test Examples
High (S-40) Pressure Switches
Low (S-69) Pressure Switches
Blower Motor
Blower Fan Resistor
HVAC Cores
Inspection and Cleaning
Heater Core and/or Evaporator Core
Compressor and Clutch
Compressor Clutch Components2 topics
  • Checking Compressor Oil for Contamination
  • Adding Compressor Oil
Clutch Procedures6 topics
  • Clutch Run-In
  • Clutch Test
  • Clutch Removal
  • Clutch Inspection
  • Clutch Installation
  • Electrical Connection
Fault Codes and Fault Finding
Electrical Terms and Equipment1 topic
  • Definition
Electrical System Components
Electrical Components Chart
Rocker Switches1 topic
  • Momentary Rocker Switches
Circuit Breakers1 topic
  • Location of Circuit Breakers
Fuses1 topic
  • Fuse Panel Identification Table
Basic Circuitry/Component Testing4 topics
  • Continuity Test for Open Circuits
  • Continuity Test for Short to Ground
  • Resistance Test for Electrical Components
  • Measuring Voltage
Diodes
Electro-hydraulic Solenoid Valve Coils1 topic
  • Operational Check
Relays
Welding on the Machine
Wiring Harnesses, Connectors, Power Sources and Controls
Connectors
Harness Splices
Fuses, Relays and Switches1 topic
  • Switch and Relay Contacts
Grounds
Power Sources
Wire Harness Identification2 topics
  • Wire Color Codes
  • Primary Harness Connectors
Ground System
Ground Points
Windrower Electronic System
Function Monitoring, Machine Configuration and Diagnostics Menus6 topics
  • Selectable Functions Monitoring
  • Machine Configuration/User Setup Menu
  • Critical Warning Displays -- Automatic Shutdown
  • Critical Warning Displays -- No Shutdown
  • Non-critical Warning Displays
  • Electrical Fault Codes
System Monitoring
Description, Power Distribution, and Troubleshooting
XCM Power
Unswitched XCM Power
Switched XCM Power1 topic
  • Power Distribution
Main Distribution Panel – Fuse Block
Unswitched Power
#2 Main Circuit Breaker
#4 Main Circuit Breaker Busbar
Battery Busbar
#1 Main Circuit Breaker Busbar
Switched Power
VI Supply Busbar
IGN Control Busbar
ACC Control Busbar
XCM Function and Configure Select Switches
Air Conditioning Systems1 topic
  • General Principles of Operation (Manual and ATC Systems)
Manual HVAC System (Standard)
A/C Clutch Circuit (Manual HVAC)
Automatic (ATC) HVAC System
General Operation5 topics
  • Heater Operation
  • Heater Operation – Sequence of Events
  • Defrosting/Defogging Operation
  • Air Conditioner (A/C) Operation
  • Ventilation
System Component Functions12 topics
  • Automatic Fan Speed Control (AUTO)
  • Manual Mode Fan Speed Control (Up/Down)
  • A/C Compressor Clutch Control
  • Heater Water Valve
  • Cab Air Temperature Sensor
  • Evaporator Probe
  • ATC HVAC Component Usage
  • Fault Codes
  • Advanced Diagnostics Display Mode
  • Revision Level
  • Setting Parameters
  • ATC Troubleshooting Quick-Checks
A/C Clutch Circuit (ATC HVAC)
Lamp Replacement Chart
Flashing Lights and Turn Signals
Road Lights, Tail Lights and Console Light Circuits
Work Lights Circuits
Exit Lighting (Left Side Stubble Light)1 topic
  • Procedure
Console and Dome Lights Circuits
General Information3 topics
  • Engine Functions for the XCM (Inputs)
  • Engine Functions for the XCM (Outputs)
  • Starting Circuits
Air Filter Switch Circuit
Fuel Level Gauge Circuit1 topic
  • Sender Resistance Chart
Coolant Temperature Circuit2 topics
  • 4-Line Display -- Engine Coolant Temperature Scale
  • A-Pillar Display -- Engine Coolant Temperature Scale
Engine Fuel Solenoid Circuit
Engine Oil Pressure Switch (S-72) Circuit
Engine Starting Motor Circuit
Fuel Lift Pump Circuit1 topic
  • Removal/Testing
Fuel Water Switch (S-59)2 topics
  • Draining the Fuel System Water (Switch Off)
  • Fuel Injection Pump Module (A-04) Connections
Thermostart System Circuit (If equipped)
Engine Boost Temperature/Pressure Sender (B-13)
Rotary Radiator Screen Cleaner Circuit
Battery2 topics
  • Size and Rating
  • How a Battery Works
Battery Troubleshooting4 topics
  • Determining the Cause of Battery Failure
  • Application and Installation
  • Service History
  • Visual Inspection
Troubleshooting Summary
Testing the Battery -- General2 topics
  • Key Off” Current Drain
  • Voltage Drop Test
Charging the Battery7 topics
  • Determining Battery Charge Procedure
  • Slow Charge Procedure: For Batteries with Charges Below 11.0 V
  • Selecting Battery Charging Method
  • Slow Charge Procedure
  • with Voltage of 11 to 12.5 V
  • Battery Charging Time Standard Charge Procedure
  • Battery Charging Precautions
Battery Specifications
Alternator12 topics
  • Charging System Excitation Circuit Operation
  • Alternator and Voltage Regulator
  • Maintaining the Alternator
  • Alternator Connections
  • Alternator and Voltage Regulator Precautions
  • Alternator Belt Tension
  • Alternator Drive Belt Removal
  • Alternator Drive Belt Replacement
  • Welding on the Machine
  • Testing the Alternator
  • Alternator Removal
  • Alternator Installation
Hydraulic Oil Level Switch Circuit
Hydraulic Oil Temperature Switch Circuit
Hydraulic Charge Pressure Switch Circuit
Seat Occupied Circuit
Header Drive Circuit
Header Reverse Circuit
Header Speed Circuit
Master Hydraulic Solenoid Circuit
Header Raise/Lower Circuit2 topics
  • Header Raise Circuit
  • Header Lower Circuit
Header Tilt Up/Tilt Down Circuit2 topics
  • Header Tilt Up Circuit
  • Header Tilt Down Circuit
Header Flotation Trim Circuit
Hydrostatic High Speed Circuit
Accessing Diagnostic Mode
Inputs9 topics
  • Engine Inputs
  • Fuel Inputs
  • Header Inputs
  • Hydraulics Inputs
  • Lights Inputs
  • Preheat Inputs
  • Propulsion Inputs
  • PTO Inputs
  • Reel Inputs
Outputs4 topics
  • Fuel Outputs
  • Header Outputs
  • HVAC Outputs
  • Preheat Outputs
Inputs and Outputs Component Chart
Wiggle Test
Display (LCD) Test
Fault History Screen
Enable/Disable the Low and Medium Priority Fault/Warning Messages
Select Audible Alarm Volume
Audible Alarm Priorities3 topics
  • Low Priority Warnings
  • Medium Priority Warnings
  • High Priority Warnings
55 000 CAN Network Basics
Fault Code Format (SPN/FMI Codes)
SPN/FMI Code Charts2 topics
  • FMI Codes
  • SPN Codes
Engine Fault Codes3 topics
  • FAULT CODE -- 101-03 Oil Pressure Switch Shorted to High Source
  • FAULT CODE -- 101-04 Oil Pressure Switch Shorted to Low Source
  • FAULT CODE -- 102-03 Air Filter Restriction Switch Shorted to High Source
Fuel Fault Codes1 topic
  • FAULT CODE -- 301-04 Fuel Water Switch Shorted to Low Source
Hydraulic Fault Codes1 topic
  • Shorted to High Source
Propulsion Fault Codes33 topics
  • FAULT CODE -- 404-03 MFH Position Sensor Shorted to High Source
  • FAULT CODE -- 404-04 MFH Position Sensor Shorted to Low Source
  • FAULT CODE -- 404-14 MFH Position Sensor Special Instructions
  • FAULT CODE -- 405-03 Pintle Arm Position Sensor Shorted to High Source
  • FAULT CODE -- 405-04 Pintle Arm Position Sensor Shorted to Low Source
  • Shorted to Low Source
  • and Pot B Needs Calibration
  • FAULT CODE -- 408-03 MFH Neutral Switch Shorted to High Source
  • FAULT CODE -- 408-07 MFH Neutral Switch Mechanical Out of Range
  • FAULT CODE -- 409-03 Park Brake Switch Shorted to High Source
  • Needs Calibration
  • FAULT CODE -- 418-03 MFH Position Sensor Shorted to High Source
  • FAULT CODE -- 418-04 MFH Position Sensor Shorted to Low Source
  • FAULT CODE -- 418-13 MFH Position Sensor Needs Calibration
  • FAULT CODE -- 419-03 MFH Position Sensor Shorted to High Source
  • FAULT CODE -- 419-04 MFH Position Sensor Shorted to Low Source
  • FAULT CODE -- 419-07 MFH Position Sensor Mechanical Out of Range
  • FAULT CODE -- 419-13 MFH Position Sensor Needs Calibration
  • FAULT CODE -- 420-03 MFH Position Sensor Shorted to High Source
  • FAULT CODE -- 420-04 MFH Position Sensor Shorted to Low Source
  • FAULT CODE -- 420-07 MFH Position Sensor Mechanical Out of Range
  • FAULT CODE -- 420-13 MFH Position Sensor Needs Calibration
  • FAULT CODE -- 421-03 MFH Position Sensor Shorted to High Source
  • FAULT CODE -- 421-04 MFH Position Sensor Shorted to Low Source
  • FAULT CODE -- 421-13 MFH Position Sensor Needs Calibration
  • FAULT CODE -- 424-13 Propulsion Forward Coil Needs Calibration
  • FAULT CODE -- 425-13 Propulsion Forward Coil Needs Calibration
  • FAULT CODE -- 426-13 Propulsion Reverse Coil Needs Calibration
  • FAULT CODE -- 427-13 Propulsion Reverse Coil Needs Calibration
  • FAULT CODE -- 431-03 MFH Position Sensor R-18 Shorted to High Source
  • FAULT CODE -- 432-03 MFH Position Sensor R-18 Shorted to High Source
  • FAULT CODE -- 433-03 Propulsion Cylinder Shorted to High Source
  • FAULT CODE -- 434-03 Propulsion Cylinder Shorted to High Source
PTO Fault Codes1 topic
  • FAULT CODE -- 200-12 Header Speed Sensor Bad Intelligent Device
Wiring Harnesses10 topics
  • FM Harness (Front)
  • FM Harness (Rear)
  • LL and LR Harnesses (Lighting)
  • FM Harness (Engine LH)
  • FM Harness (Engine RH)
  • CM Harness (Electrical Panel)
  • CM Harness (Inside Cab)
  • CM Harness (Seat and Right Hand Console)
  • OR Harness (Outside Roof)
  • RM Harness (Inside Roof)
Standard Wire Harnesses
FM Wire Harness Connectors
CM Wire Harness Connectors
SC Wire Harness Connectors

Inside this manual

Real pages from this service manual (1,573 pages). Open the sample pages (PDF, 669 KB)

Sample pages from the New Holland HW345, HW365 Windrower Service Manual: Specifications, Diagram, Troubleshooting, Color page, Color page
  • Specifications, page 161: SECTION 10 -- ENGINE -- CHAPTER 1
  • Diagram, page 929: SECTION 55 - ELECTRICAL SYSTEMS - CHAPTER 7
  • Troubleshooting, page 1,169: SECTION 55 - ELECTRICAL SYSTEMS - CHAPTER 11
  • Color page: SECTION 55 - ELECTRICAL SYSTEMS - CHAPTER 5
  • Color page: SECTION 90 - PLATFORM, CAB AND DECALS - CHAPTER 1

This is a service manual

Here's how it compares to the other manual types.

This manual

Service manual

Factory repair procedures and technical information such as specifications, troubleshooting, and wiring and hydraulic diagrams, for the models and systems the manual covers. See What's inside for its topics.

Operator's manual

Safe operation, controls, maintenance schedules, lubrication points, inspections, and basic checks. Repair procedures are in the service manual.

Parts manual

Illustrated diagrams with factory part numbers for identifying components and ordering parts. Repair procedures are in the service manual.

Engine service manuals are sometimes sold separately, since certain machine models were offered with more than one engine option.

What it's used for

Factory manual for in-house farm and construction shop use. Straightforward, complete, and easy to follow. It contains the OEM information dealership service departments and parts counters use to diagnose problems, identify components, and perform maintenance or repairs correctly.

Service shops and owner/operators who repair their own equipment

Identifying correct parts and seeing how assemblies come apart and go back together

Keeping equipment running with less downtime

Factory manual, 1,573 pages

Quantity one is the manual described above.

Fast free USA shipping

Ships in 1 business day.

60-day returns

Free if the mistake is ours. A manual ordered in error must come back unopened in its shrink-wrap; you pay return shipping and a 20% restocking fee applies. Return policy

Binder not included

Manuals over about 300 pages may need a standard 3-ring binder, which you can buy locally to keep the pages organized for shop use.

Questions about model, serial number, engine coverage or contents? Contact us before purchasing and we'll help confirm it's the right manual. Please verify the manual type, machine model, serial number range and engine coverage before purchasing: manuals ordered in error carry a 20% restocking fee (return policy).