New Holland TD3.50 Tractor Service Manual
501 pages · Publication 47840677
Added to your cart. View cart
- Models
- TD3.50
- Manual type
- Service Manual
- Pages
- 501
- Publication
- 47840677
- Condition
- Brand new
What's inside
From the manual's own table of contents: 22 sections, 191 entries. See sample pages (PDF, 642 KB)
HOLLAND23 topics
- General Instructions
- Notes for spare parts
- Notes for equipment
- Safety Rules
- Consumables
- Specifications
- Tightening Torques
- Special Tools
- Cross Sectional Views
- Engine Cooling System
- Troubleshooting
- Engine - Remove and Install
- Engine Removal and Overhaul
- Engine Timing Gear Cover, Timing Gears, and Cam Shaft
- Cylinder Head
- Valves
- Cylinder Block
- Pistons
- Crankshaft - Main Bearing and Thrust Washer
- Camshaft
- Hydraulic Oil Pump
- Description of operation - Engine Lubrication System
- Description of operation - Cooling System
Electrical Circuits9 topics
- Fuses (all versions)
- Symbols used in electrical circuits
- Electrical wire colour coding
- Ground location points
- General electrical diagram
- Start-up circuit
- Direction indicator & hazard warning light circuit
- Worklamp
- Side Lights, main and dipped headlights, parking light circuit
SECTION 10 -- ENGINE -- CHAPTER 17 topics
- Technical Information
- Fuel system technical data
- Angular tightening torque values
- Longitudinal and cross sectional views of the engine
- Cross sectional view of the lubrication system
- Removal - Installation - Overhaul
- Checking, dimensions and overhaul
SECTION 18 - CLUTCH PEDAL - CHAPTER 121 topics
- General Specifications
- Tightening Torque Values
- Sectional View
- Removal- Installation
- General Repair
- Control, Measurement and Repair
- Adjustments
- Type
- Operation
- Separation Mechanism
- Transmission Clutch Disk
- PTO Clutch Disk
- All Models
- Valeo
- Wear Limit
- Transmission Pressure Plate
- PTO Pressure Plate
- See page 18
- Operating clearance of PTO clutch disengaging sleeve
- Disengagement tines setting
- Clutch mechanism setting
SECTION 21 - TRANSMISSION - CHAPTER 12 topics
- Liquid Sealants
- Description and Operation
SECTION 21 - TRANSMISSION - CHAPTER 24 topics
- General Recommendations For Overhauling Operations
- Transmission Assembly, Removal - Installation
- Transmission - Mechanical - Disassemble 8x8 Shuttle Transmission
- Gear Assembly
SECTION 23 - DRIVELINES - CHAPTER 114 topics
- Torque Settings and Tools
- Cross-Sectional Views
- Transmission shafts and guard (Disassembly - Assembly)
- Drive gear housing (Removal - Installation)
- Drive gear housing removed (Disassembly - Assembly)
- Reduction ratio
- Relay lever wear pad width
- Pad seat width in driven gear
- Pad clearance in seat
- Relay lever pivot diameter
- Pivot housing bore in casing
- Pivot clearance in housing
- Free
- Front drive sleeve shim thickness
SECTION 25 - FRONT MECHANICAL AXLE TRANSMISSIONS - CHAPTER 110 topics
- Tools
- Complete front axle. Remove - Install
- Front axle Remove - Install
- Steering knuckle bearing pins. Replace
- Stub axle adjustment
- Wheel hub bearing adjustment
- Bevel drive adjustment
- Front axle differential. Overhaul
- Front axle differential with LIM-SLIP - Overhaul
- Leading drive wheels toe-in check
SECTION 27 - REAR AXLE AND TRANSMISSION - CHAPTER 15 topics
- Seals
- Low Gear Drive Line Schema
- High Gear Drive Line Schema
- Reverse Gear Drive Line Schema
- Internal Components, Disassembly - Assembly
SECTION 27 - REAR AXLE AND TRANSMISSION - CHAPTER 25 topics
- Differential assembly
- Differential pinion and side gear backlash
- Repair and Inspection
- Adjustment of bevel wheel bearings and crown pinion backlash adjustment
- Final drive housing
SECTION 31 - PTO - CHAPTER 14 topics
- RemovalInstallation - Overhaul
- Engagement and Control
- Rotation (looking from tractor rear end)
- Number of splines
SECTION 33 - BRAKE SYSTEM - CHAPTER 13 topics
- Brake Control, Removal - Installation
- Brake Assembly, Removal - Installation
- Brake Pedal Free Play Setting
SECTION 35 - HYDRAULIC SYSTEM - CHAPTER 13 topics
- Introduction and Circuit Identification
- Open Centre High Pressure Hydraulic Circuit
- Hydraulic Circuit Diagram
BÖLÜM 35 -HYDRAULIC SYSTEMS - CHAPTER 28 topics
- Remove - Install
- Disassembly - Assembly
- Location
- Installation
- Manufacturer
- Drive
- Rotation (from drive end)
- Engine / Pump rpm ratio
SECTION 35 - HYDRAULIC SYSTEM - CHAPTER 34 topics
- Operation of Distributor
- Internal Three-Point Hitch
- Operation of Internal Lift-O-Matic Levers
- Adjustment and Settings
SECTION 41 - HYDRAULIC SYSTEM - CHAPTER 16 topics
- Hydraulic circuit
- Oil Filter
- Brand
- DANFOSS
- ORSTA
- 4WD model
SECTION 55 - ELECTRICAL SYSTEM - CHAPTER 13 topics
- Semi-digital instruments Introduction
- Transmitters, sensors and switches
- INTRODUCTION
SECTION 55 - ELECTRICAL SYSTEM - CHAPTER 22 topics
- Description of the component
- Instrument console control
SECTION 55 - ELECTRICAL SYSTEM - 3 CHAPTER13 topics
- Description and operation of the system
- STARTING CIRCUIT
- System testing
- Starter motor - Remove - Install
- Service
- Bench test
- Power (kW)
- Number of teeth
- Starter motor - Crankcase fixing nut
- Starter motor box - ground cable side
- Solenoid valve nut
- Nut on the starter motor
- Solenoid valve fixing bolts
SECTION 55 - ELECTRICAL SYSTEM - 4 CHAPTER11 topics
- Testing the system and troubleshooting
- Removal - Installation and service
- Nominal voltage (V)
- Nominal current (A)
- Resistance of the windings (W)
- ponents (kg/cm2)
- Alternator tightening torques
- Pulley fixing bolts
- Rectifier fixing screws
- Brush box and regulator screws
- Terminal nuts
SECTION 55 - ELECTRICAL SYSTEM - CHAPTER 59 topics
- Removal and Re-installation
- Battery Checking and Maintenance
- Battery Charging
- Battery Problems - Frequent Causes
- Voltage (V)
- Capacity (Ah)
- Number of elements
- Number of plates per element
- Energy reserve (SAE) (min.)
SECTION 55 - ELECTRICAL SYSTEM - CHAPTER 63 topics
- General electrical diagram
- Brake lamp circuit
- Worklamp
Inside this manual
Real pages from this service manual (501 pages). Open the sample pages (PDF, 641 KB)
- Specifications, page 156: SECTION 18 - CLUTCH PEDAL - CHAPTER 1
- Troubleshooting, page 457: SECTION 55 - ELECTRICAL SYSTEM - 4 CHAPTER
- Color page, page 260: SECTION 27 - REAR AXLE AND TRANSMISSION - CHAPTER 1
- Color page, page 363: SECTION 35 - HYDRAULIC SYSTEM - CHAPTER 3
- Foldout diagram (color), page 406: SECTION 41 - HYDRAULIC SYSTEM - CHAPTER 1 11
This is a service manual
Here's how it compares to the other manual types.
Service manual
Factory repair procedures and technical information such as specifications, troubleshooting, and wiring and hydraulic diagrams, for the models and systems the manual covers. See What's inside for its topics.
Operator's manual
Safe operation, controls, maintenance schedules, lubrication points, inspections, and basic checks. Repair procedures are in the service manual.
Parts manual
Illustrated diagrams with factory part numbers for identifying components and ordering parts. Repair procedures are in the service manual.
Engine service manuals are sometimes sold separately, since certain machine models were offered with more than one engine option.
What it's used for
Factory manual for in-house farm and construction shop use. Straightforward, complete, and easy to follow. It contains the OEM information dealership service departments and parts counters use to diagnose problems, identify components, and perform maintenance or repairs correctly.
Service shops and owner/operators who repair their own equipment
Identifying correct parts and seeing how assemblies come apart and go back together
Keeping equipment running with less downtime
Factory manual, 501 pages
Quantity one is the manual described above.
Fast free USA shipping
Ships in 1 business day.
60-day returns
Free if the mistake is ours. A manual ordered in error must come back unopened in its shrink-wrap; you pay return shipping and a 20% restocking fee applies. Return policy
Binder not included
Manuals over about 300 pages may need a standard 3-ring binder, which you can buy locally to keep the pages organized for shop use.
Other editions and similar models
Questions about model, serial number, engine coverage or contents? Contact us before purchasing and we'll help confirm it's the right manual. Please verify the manual type, machine model, serial number range and engine coverage before purchasing: manuals ordered in error carry a 20% restocking fee (return policy).