New Holland TD5010, TD5020, TD5030, TD5040, TD5050 Tractor Service Manual
691 pages · Publication 84176561B
Added to your cart. View cart
What's inside
From the manual's own table of contents: 22 sections, 265 entries. See sample pages (PDF, 743 KB)
HOLLAND21 topics
- General instructions
- Notes for spare parts
- Notes for equipment
- Safety rules
- Consumables
- Tools
- Engine Troubleshooting
- Engine R.I
- General specifications
- Data
- Tightening torques
- Engine views
- Lubrication diagram
- Cooling system diagram
- Fault diagnosis
- Engine D.A. Checks, measurements and repairs
- Crankshaft front seal - Replacement
- Crankshaft rear seal - Replacement
- Valve tappet and rocker arm clearance - Adjustment
- Engine injector R.I
- Bosch injection pump R.I. Timing. Air bleed
SECTION 10 - ENGINE - CHAPTER 14 topics
- Coolant pump R.I
- Thermostat valve R.I
- Radiator R.I
- Coolant pump and generator drive belts. Tension adjustment
SECTION 18 - CLUTCH - CHAPTER 114 topics
- Cross-sectional views
- Clutch Troubleshooting
- Removal - Installation
- Overhaul
- Minimum permissible dimensions after refacing
- Adjustments
- Adjustment of the main and PTO clutch control linkage
- Type
- Mechanical
- Engagement and release mechanism
- Driven plate lining material for main transmission clutch (11”)
- Models TD5030
- Release lever coplanarity adjustment
- Clutch control adjustment
SECTION 21 - TRANSMISSIONS - CHAPTER 115 topics
- Main data
- Description and operation
- Gearbox
- Gearing type
- Range gear
- Slow
- Normal
- Fast
- Gearbox and range gear controls
- Inside diameter of gearbox driven gears
- Outside diameter of bushings (17, page 5)
- Clearance between gears and bushings
- Diameter of gearbox driven shaft (19, page 5)
- Inside diameter of bushings (17, page 5)
- Clearance between shaft and bushings
SECTION 21 - TRANSMISSIONS - CHAPTER 25 topics
- Section views
- Removal-Refitting
- Control
- Reduction unit
- Gearbox and reduction unit controls
SECTION 21 - TRANSMISSIONS - CHAPTER 31 topic
- Reduction ratio
SECTION 23 − DRIVE LINES − CHAPTER 114 topics
- Main specification
- Torque settings and Tools
- Cross−Sectional views
- Transmission shafts and guard (Disassembly − Assembly)
- Drive gear housing (Removal − Installation)
- Drive gear housing removed (Disassembly − Assembly)
- Relay lever pad width
- Pad seat width in driven gear
- Pad clearance in seat
- Relay lever pivot diameter
- Pivot housing bore in casing
- Pivot clearance in housing
- − Free
- Front drive sleeve shim thickness
SECTION 25 - MECHANICAL FRONT AXLE - CHAPTER 111 topics
- Complete front axle. Removal - Installation
- Front axle. Removal - Installation
- Steering knuckle bearing pins. Replacement
- Stub axle adjustment
- Wheel hub bearing adjustment
- Bevel drive adjustment
- Front axle differential. Overhaul
- Front axle differential with LIM-SLIP. Overhaul
- Front axle differential with NO SPIN. Overhaul
- Leading drive wheels toe-in check
- TD5050 Model
SECTION 27 − REAR AXLE AND TRANSMISSION − CHAPTER 118 topics
- Special tools
- Description and operation and troubleshooting
- 21.118.10 − 12 Transmission−gearbox casing Removal−Installation
- Transmission−gearbox casing Disassembly−Overhaul
- Gearbox driven shaft end float adjustment
- Differential lock engagement sleeve adjustment
- Determining the bevel pinion positioning adjustment ring
- Adjusting the taper roller bearings for the bevel pinion shaft
- Adjusting the bearings and checking the backlash
- Differential pinion and side gear backlash adjustment
- Bevel gear pair gear ratio
- Bevel gear pair tooth clearance
- Type of differential
- Mechanical differential lock control
- Differential pinion internal seat diameter
- Differential pinion pin diameter
- Diameter of side gear hubs
- Clearance between side gears and their seats
SECTION 31 - POWER TAKE-OFF - CHAPTER 114 topics
- Torque settings
- Sectional drawings
- Troubleshooting
- Removal - Refitting
- Bench overhaul
- Type (Independent and ground speed PTO)
- Engagement and control
- Direction of rotation (viewed from rear of tractor)
- Engine speed with PTO shaft rotating at 540 rev/min
- rev/min
- (30 km/h version)
- (4WD 40 km/h version)
- Diameter of PTO shaft at position of bearings
- Diameter of PTO shaft at splined end
SECTION 33 - BRAKING SYSTEM - CHAPTER 114 topics
- Description & Operation
- Tools - Troubleshooting
- overhauling on the bench
- Service brake removal and refitting
- Removal-Refitting of front brake pumps
- Bleeding air from the front braking system
- Adjusting service brake pedals travel
- Parking brake travel adjustment
- service brake
- parking brake
- Disc material for service brake
- Disc material for parking brake
- Mobile sector material for parking brake
- service brakes
SECTION 35 - HYDRAULIC SYSTEM - CHAPTER 114 topics
- Hydraulic circuit
- Description and operation of lift phases
- Hydraulic lift - disassembly reassembly
- Hydraulic lift - bench overhaul
- Adjusting the lift
- Linkage adjustment
- Pressure relief valve - disassembly reassembly
- Pressure relief valve - setting
- Lift control valve - disassembly assembly and overhaul on bench
- Lift pump
- Operating system
- LIFT-O-MA TIC
- Pressure relief valve setting
- Cylinder safety valve setting
SECTION 35 - HYDRAULIC SYSTEM - CHAPTER 210 topics
- Main data - Tools
- Auxiliary control valves - sectional views
- Auxiliary control valves - Assembly-Disassembly
- Spool binding test
- Spool leakage test
- Adjustment of the automatic detent release pressure
- Filter
- Pump
- Location
- Operation
SECTION 35 - HYDRAULIC SYSTEM - CHAPTER 33 topics
- Hydraulic diagram
- Description and operation of valve phases
- Trailer brake auxiliary control valve linkage adjustment
SECTION 41 - STEERING - CHAPTER 113 topics
- Principal data
- Hydrostatic steering control valve - Removal-Installation
- Hydrostatic steering control valve - Disassembly-Assembly
- Hydrostatic steering control valve - Bench testing
- Hydrostatic steering oil pump - Disassembly-Assembly
- Steering cylinder (two-wheel drive axle) - Removal-Refitting
- Steering cylinder (four wheel drive axle) - Removal-Refitting
- Oil filter
- Make
- DANFOSS
- ORSTA
- 2WD models
- 4WD models
SECTION 44 - FRONT AXLE AND WHEELS - CHAPTER 112 topics
- Sectional views
- Equipment - Fault diagnosis
- Removal-Refitting-Overhaul
- Wheel hub disassembly-assembly
- Stub axle overhaul
- Checking wheel alignment
- Wheel angle
- Diameter of stub axle pin (7, page 8) at bushing
- Bore of installed bushings (6)
- Clearance between stub axle pin and relative bushings
- Diameter of axle articulation pin (1, page 8)
- Clearance between stub axle pin and bushing
SECTION 50 - AUXILIARY UNITS - CHAPTER 117 topics
- Safety instructions
- General characteristics
- Equipment
- Operating principles
- Cab controls
- Main components of the cab air conditioning system
- Refrigerant recovery-recycling and evacuation-charging stations
- Drying recharging and checking cooling
- Functional testing of air conditioning system
- Summary of the cab air-conditioning system charging operations
- Checking for refrigerant leaks using an electronic leak detector
- Summary of fault diagnosis and maintenance
- Air conditioning and heating pipes - Replacement
- Receiver-drier - Replacement
- Condenser - Replacement
- Compressor - Removal-Refitting
- Compressor drive belt tension adjustment
SECTION 55 - ELECTRICAL SYSTEM - CHAPTER 12 topics
- Analogue instruments Introduction
- INTRODUCTION
SECTION 55 - ELECTRICAL SYSTEM - CHAPTER 21 topic
- Component description
SECTION 55 - ELECTRICAL SYSTEM - CHAPTER 322 topics
- Technical information
- Starting circuit
- System tests
- Removal and re-installation of starter motor
- Servicing
- Bench tests
- Power (kW)
- and 8600 rev/min
- System testing and trouble-shooting
- Removal, re-installation and servicing
- Nominal voltage (V)
- Max rotation speed (rpm)
- Maximum output (A)
- Removal and re-installation
- Battery checking and maintenance
- Charging the battery
- Battery problems - Frequent causes
- Voltage (V)
- Capacity (Ah)
- Number of elements
- Number of plates per element
- Energy reserve (SAE) (min.)
SECTION 55 - ELECTRICAL SYSTEM - CHAPTER 615 topics
- Fuses (all versions)
- Symbols used in electrical circuits
- Electrical wire colour coding
- Ground locations
- Electrical diagrams
- General diagrams (W/Cab)
- General diagrams (W/Out Cab)
- Analogue instrument circuit and connector overview
- Start-up circuit and connector overview
- Direction indicator & hazard warning light circuit and connector overview
- Windscreen and rear window wiper/washer circuit and connector overview
- Brake light circuit and connector overview
- Heating and air-conditioning system circuit and connector overview
- Work lamp (without cab circuit and connector overview)
- overview
SECTION 90 - CAB - CHAPTER 13 topics
- Disassembly-Assembly
- interior light switches (3) and remove the cover
- Remove the LH panel retaining screws (1)
Inside this manual
Real pages from this service manual (691 pages). Open the sample pages (PDF, 743 KB)
- Troubleshooting, page 60: SECTION 10 - ENGINE - CHAPTER 1
- Specifications, page 270: SECTION 25 - MECHANICAL FRONT AXLE - CHAPTER 1
- Diagram, page 650: SECTION 55 - ELECTRICAL SYSTEM - CHAPTER 6
- Color page, page 442: SECTION 35 - HYDRAULIC SYSTEM - CHAPTER 2
- Color page, page 471: SECTION 41 - STEERING - CHAPTER 1
- Foldout diagram (color): SECTION 33- BRAKING SYSTEM - CHAPTER 1
Other manuals for this machine
Save 10% on 2 manuals, 15% on 3 or more. Other manuals for the TD5010, TD5020, TD5030, TD5040, TD5050 are listed below. Editions cover different serial number ranges: check the serial coverage and tick only the ones that match your machine.
Added to your cart. View cart
This is a service manual
Here's how it compares to the other manual types.
Service manual
Factory repair procedures and technical information such as specifications, troubleshooting, and wiring and hydraulic diagrams, for the models and systems the manual covers. See What's inside for its topics.
Operator's manual
Safe operation, controls, maintenance schedules, lubrication points, inspections, and basic checks. Repair procedures are in the service manual.
Parts manual
Illustrated diagrams with factory part numbers for identifying components and ordering parts. Repair procedures are in the service manual.
Engine service manuals are sometimes sold separately, since certain machine models were offered with more than one engine option.
What it's used for
Factory manual for in-house farm and construction shop use. Straightforward, complete, and easy to follow. It contains the OEM information dealership service departments and parts counters use to diagnose problems, identify components, and perform maintenance or repairs correctly.
Service shops and owner/operators who repair their own equipment
Identifying correct parts and seeing how assemblies come apart and go back together
Keeping equipment running with less downtime
Factory manual, 691 pages
Quantity one is the manual described above.
Fast free USA shipping
Ships in 1 business day.
60-day returns
Free if the mistake is ours. A manual ordered in error must come back unopened in its shrink-wrap; you pay return shipping and a 20% restocking fee applies. Return policy
Binder not included
Manuals over about 300 pages may need a standard 3-ring binder, which you can buy locally to keep the pages organized for shop use.
Questions about model, serial number, engine coverage or contents? Contact us before purchasing and we'll help confirm it's the right manual. Please verify the manual type, machine model, serial number range and engine coverage before purchasing: manuals ordered in error carry a 20% restocking fee (return policy).