New Holland TL60E, TL75E, TL85E, TL95E Tractor Service Manual
637 pages · Publication 84281020
Added to your cart. View cart
What's inside
From the manual's own table of contents: 13 sections, 204 entries. See sample pages (PDF, 717 KB)
ENGINE9 topics
- GENERAL FEATURES
- MAIN DATA
- TIGHTENING TORQUE
- TOOLS
- CROSS-SECTIONS
- LUBRICATION AND COOLING SCHEMATICS
- ENGINE TROUBLESHOOTING
- DISASSEMBLEY – INSTALLATION – SERVICING
- BLEEDING
CLUTCH6 topics
- CUT SECTIONS
- CLUTCH TROUBLESHOOTING
- DISASSEMBLING – INSTALLING
- SERVICING
- CHECKING, MEASURING AND REPAIRING
- ADJUSTMENTS
TRANSMISSION8 topics
- SPECIFICATIONS
- TORQUE DATA
- SPECIAL TOOLS
- CUTOUT DRAWINGS
- HYDRAULIC DESCRIPTION, OPERATION AND DIAGRAMS
- DISASSEMBLY AND INSTALLATION
- DESCRIPTION AND OPERATION
- TROUBLESHOOTING
TRANSMISSION SHAFT3 topics
- DESCRIPTION, OPERATION AND HYDRAULIC DIAGRAMS
- DISASSEMBLY – REPAIRING
- DISASSEMBLY – ASSEMBLY
FRONT WHEEL DRIVE8 topics
- TORQUES
- FRONT SHAFT – DISASSEMBLY
- FRONT WHEEL DRIVE DIFFERENTIAL
- CONICAL PINION ADJUSTMENTS (PINION DEPTH)
- CONICAL PINION ADJUSTMENTS
- DIFFERENTIAL ADJUSTMENTS
- PINS AND BALL BUSHES
- TURNING CASE ADJUSTMENT
REAR TRANSMISSION7 topics
- CROSS-SECTION DRAWINGS
- SEPARATING THE TRANSMISSION FROM THE TRACTOR – WITH CAB
- REAR TRANSMISSION – ASSEMBLY – TRACTORS WITH CAB
- SEPARATING THE TRANSMISSION FROM THE TRACTOR – WITH PLATFORM
- REAR TRANSMISSION – ASSEMBLY – TRACTORS WITH PLATFORM
- TRANSMISSION BOX – ADJUSTMENTS
- REAR AXLE END SET (END REDUCTION)
POWER TAKE OFF3 topics
- BENCH SERVICING
- CUT DRAWINGS
- DESCRIPTION, OPERATION AND DIAGRAMS FOR HYDRAULIC CIRCUITS
BRAKING SYSTEM3 topics
- DISASSEMBLING – REPAIRING – SERVICING THE SERVICE BRAKE
- DISASSEMBLING – REPAIRING THE SERVICE BRAKE CYLINDERS
- DISASSEMBLING – REPAIRING – SERVICING THE PARKING BRAKE
HYDRAULIC SYSTEM4 topics
- REMOVAL FROM TRACTOR
- ASSEMBLING ON THE TRACTOR
- BENCH SERVICE
- HYDRAULIC DIAGRAMS
STEERING7 topics
- CONTROL VALVE SPECIFICATIONS
- TIGHTENING TORQUES
- STEERING PUMP SPECIFICATIONS
- STEERING CIRCUIT PRESSURE TEST
- STEERING MOTOR – SERVICE
- STEERING CYLINDER SERVICE
- HYDROSTATIC STEERING OIL PUMP – SERVICE
FRONT AXLE AND WHEELS4 topics
- FRONT AXLE -DISASSEMBLY – REPAIRING – SERVICING
- WHEEL HUB DISASSEMBLY – ASSEMBLY
- STUB AXLE SERVICING
- CHECKING FRONT WHEEL ALIGNMENT
AUXILIARY UNITS17 topics
- SAFETY PRECAUTIONS
- PRINCIPLES OF THE AIR CONDITIONER
- CAB HEATING AND VENTILATION CONTROLS
- CAB AIR CONDITIONER CONTROLS
- USING THE AIR CONDITIONER SYSTEM
- SYSTEM COMPONENTS – DESCRIPTION AND OPERATION
- TROUBLESHOOTING AND TESTING THE AIR CONDITIONING SYSTEM
- TESTING PROCESS
- PERFORMANCE DIAGNOSTIC TESTS
- EXAMPLES OF READING GAUGES AND THEIR INTERPRETATIONS
- PERFORMANCE TEST: EXAMPLE 1
- WASHING THE AIR CONDITIONING SYSTEM
- EVACUATING THE AIR CONDITIONING SYSTEM
- CHARGING THE AIR CONDITIONING SYSTEM
- SERVICING COMPONENTS (EXCLUDING THE COMPRESSOR) THE BASICS
- COMPRESSOR DRIVE BELT – ADJUSTMENT
- AIR CONDITIONER AND HEATING PIPES – REPLACEMENT
ELECTRICAL SYSTEM112 topics
- ANALOG DASHBOARD
- TRANSMITTERS, SENSORS AND SWITCHES
- INTRODUCTION
- DESCRIPTION AND OPERATION OF COMPONENTS
- FUSE AND RELAY BOX
- HEADLIGHTS – ADJUSTMENT
- BULBS – REPLACING
- STARTER MOTOR OPERATION
- STARTER CIRCUIT ELECTRICAL DIAGRAM
- TRIAL OF THE STARTER SYSTEM ON THE TRACTOR
- REMOVING AND INSTALLING THE STARTER MOTOR
- DISASSEMBLING AND ASSEMBLING THE STARTER MOTOR
- BENCH TRIALS
- SERVICING THE ALTERNATOR AND TESTING THE COMPONENTS
- INSPECTION AND REPAIR
- REMOVAL AND INSTALLATION
- MAINTAINING AND TESTING THE BATTERY
- PERFORMANCE TESTS
- CHARGING TESTS
- COMMONEST CAUSES OF BATTERY DAMAGE
- COLOR CODE AND CIRCUIT IDENTIFICATION
- FUSES BOX AND RELAY LAY OUT
- TABLE OF FUSES
- ISOBUS – SUPPLY SYSTEM – CAB – LOCATION PAGE 6
- TRAILER COMPONENTS – LOCATION PAGE 7
- ISOBUS – TRACTOR/IMPLEMENT CONNECTOR – LOCATION PAGE 8
- ISOBUS – CIRCUITS – LOCATION PAGE 9
- MAIN CAB HARNESS – SWITCHES – LOCATION PAGE 10
- ISOBUS – CAB CONNECTORS – LOCATION PAGE 11
- MAIN CAB HARNESS – SWITCHES – LOCATION PAGE 12
- MAIN CAB HARNESS – SEAMS – LOCATION PAGE 13
- MAIN CAB HARNESS – RELAY/FUSE BOX – LOCATION PAGE 14
- MAIN CAB HARNESS – ELECTRICAL COMPONENTS – LOCATION PAGE 15
- MAIN CAB HARNESS – RELAY/FUSE BOX – LOCATION PAGE 16
- ENGINE ELECTRICAL COMPONENTS – LOCATION PAGE 17
- TRANSMISSION ELECTRICAL COMPONENTS – LOCATION PAGE 18
- MAIN CAB HARNESS – GROUNDING – LOCATION PAGE 19
- ENGINE HOOD – HEADLIGHT – LOCATION PAGE 20
- RIGHT SIDE ROOF – LOCATION PAGE 21
- LEFT SIDE ROOF – LOCATION PAGE 22
- RIGHT SIDE ROOF – AIR CONDITIONER – LOCATION PAGE 23
- DASHBOARD – LOCATION PAGE 24
- INJECTION PUNP – DISASSEMBLY, ASSEMBLY, SYNCHRONIZATION AND BLEEDING
- Cycle
- Injection
- No. of in–line cylinders
- mod TL60E
- mod TL75E
- mod TL85E
- mod TL95E
- Piston stroke
- Compression ratio
- Maximum power rpm
- Max. torque rpm: mod TL60E
- Max. torque rpm: mod TL75E
- Max. torque rpm: mod TL85E
- Max. torque rpm: mod TL95E
- Number of main bushings
- Sump
- Lubrication
- Pump control
- Engine rpm and oil pump ratio
- Oil filtering
- hot and running at maximum rpm
- Pressure limiting valve
- Initial valve opening pressure
- For more technical data on lubrication
- Cooling
- Radiator for mod. TL60E and TL75E
- Radiator for mod TL85E, TL95E
- Fan fastened to the water pump pulley
- Water pump
- Engine rpm and water pump ratio
- Temperature control
- Water thermometer
- Initial blue range
- Central green range
- Final red range
- For more technical data about the cooling installation
- Rev count
- Drive
- Gauge calibrated for engine at
- Distribution
- start: before TDC
- finish: after BDC
- start: before BDC
- finish: after TDC
- intake
- exhaust
- For more technical data on distribution
- Air filtering
- Feeding pump
- Fuel filtering
- control shaft at 1600 rpm
- Cam controlled
- BOSCH injection pump
- DELPHI injection pump
- BOSCH
- DELPHI
- GARRET type
- Injection pump
- Direction of rotation
- Injection sequence
- BOSCH type
- Injection holder type
- Injector type
- DELPHI TYPE
- Number of holes
- Diameter of injector holes
- Calibration pressure (bar)
- type
- pipe dimension
Inside this manual
Real pages from this service manual (637 pages). Open the sample pages (PDF, 715 KB)
- Specifications, page 226: SECTION 25 – FRONT WHEEL DRIVE – CHAPTER 1
- Troubleshooting, page 451: SECTION 41 – STEERING – CHAPTER 1
- Diagram, page 595: SECTION 55 – ELECTRICAL SYSTEM – CHAPTER 4
- Color page, page 434: SECTION 35 – HYDRAULIC SYSTEM – CHAPTER 2
- Color page, page 33: SECTION 10 – ENGINE – CHAPTER 1
- Foldout diagram, page 634: SECTION 55 – ELECTRICAL SYSTEM – CHAPTER 6
This is a service manual
Here's how it compares to the other manual types.
Service manual
Factory repair procedures and technical information such as specifications, troubleshooting, and wiring and hydraulic diagrams, for the models and systems the manual covers. See What's inside for its topics.
Operator's manual
Safe operation, controls, maintenance schedules, lubrication points, inspections, and basic checks. Repair procedures are in the service manual.
Parts manual
Illustrated diagrams with factory part numbers for identifying components and ordering parts. Repair procedures are in the service manual.
Engine service manuals are sometimes sold separately, since certain machine models were offered with more than one engine option.
What it's used for
Factory manual for in-house farm and construction shop use. Straightforward, complete, and easy to follow. It contains the OEM information dealership service departments and parts counters use to diagnose problems, identify components, and perform maintenance or repairs correctly.
Service shops and owner/operators who repair their own equipment
Identifying correct parts and seeing how assemblies come apart and go back together
Keeping equipment running with less downtime
Factory manual, 637 pages
Quantity one is the manual described above.
Fast free USA shipping
Ships in 1 business day.
60-day returns
Free if the mistake is ours. A manual ordered in error must come back unopened in its shrink-wrap; you pay return shipping and a 20% restocking fee applies. Return policy
Binder not included
Manuals over about 300 pages may need a standard 3-ring binder, which you can buy locally to keep the pages organized for shop use.
Other editions and similar models
Questions about model, serial number, engine coverage or contents? Contact us before purchasing and we'll help confirm it's the right manual. Please verify the manual type, machine model, serial number range and engine coverage before purchasing: manuals ordered in error carry a 20% restocking fee (return policy).