New Holland TN60A, TN70A, TN75A, TN85A, TN95A Tractor Service Manual
1,191 pages · Publication 87393899
Added to your cart. View cart
What's inside
From the manual's own table of contents: 70 sections, 200 entries. See sample pages (PDF, 800 KB)
General28 topics
- SECTION 00 - GENERAL
- SECTION 10 - ENGINE
- SECTION 18 - CLUTCH
- SECTION 21 - TRANSMISSIONS
- SECTION 23 - FWD TRANSFER BOX
- SECTION 25 - FRONT AXLE MECHANICAL FWD
- SECTION 27 - REAR MECHANICAL TRANSMISSION
- SECTION 31 - MECHANICAL POWER TAKE-OFF
- SECTION 33 - BRAKING SYSTEM
- SECTION 35 - HYDRAULIC SYSTEM
- SECTION 41 - STEERING
- SECTION 44 - AXLES AND WHEELS
- SECTION 55 - ELECTRICAL SYSTEM
- SECTION 90 - PLATFORM, CAB, BODYWORK
- General Instructions
- Health and Safety
- Precautionary Statements
- Safety
- Ecology and the Environment
- Minimum Hardware Tightening Torques
- Federal Emissions Warranty
- Lubricants and Fluids
- Specifications
- Special Tools
- Tightening Torques
- Sectional Views
- Engine Troubleshooting
- Overhaul
10 102 70 Crankshaft Front Oil Seal4 topics
- Special Tools
- Sectional Views
- Description and Operation
- Overhaul
10 402 30 Cooling System Thermostat9 topics
- Special Tools
- Description and Operation
- Overhaul
- Tightening Torques
- Description and Operation
- Troubleshooting
- Overhaul
- Description of Operation
- Overhaul
10 414 10 Coolant Pump and Alternator Belts2 topics
- Lubrication System Components
- Overhaul
10 246 14 Bosch Injection Pump8 topics
- Tightening Torques
- Troubleshooting
- Description and Operation
- Torque settings
- Special Tools
- Cross-sectional views
- Description and operation
- Troubleshooting
21 118 85 Rear Transmission/Gearbox, Disassembly--Assembly1 topic
- Transmission/Gearbox, driving and driven shafts clearance adjustments
21 130 11 Range Gear Control Lever, Removal--Installation2 topics
- Torque values
- Cross-sectional views
21 154 60 Clutch casing, Disassembly--Assembly9 topics
- Fault Codes Indication
- Description of Systems (ECM and CDU)
- Description of Systems (ECM and EST)
- Fault Codes
- Torque settings
- Tools
- Cross--sectional views
- Description and operation
- Troubleshooting
23 202 52 Drive gear housing assembly removed, Disassembly -- Assembly2 topics
- Tools
- Cross--sectional Views
Show all 71 sections
44 511 80 Front Wheels Toe-in Check2 topics
- Description and operation
- Troubleshooting
27 120 32 Epicyclic Final Drive, Removal--Installation3 topics
- Tightening torques
- Sectional views
- Troubleshooting
31 112 20 Mechanical PTO assembly -- Removal--Installation1 topic
- Cross--Sectional Views
33 110 08 Handbrake Control. Stroke Adjustment2 topics
- Precautionary statements
- Description and Operation
35 104 High-pressure system hydraulic pump1 topic
- Hydraulic system configuration table
35 110 Mechanically controlled hydraulic lift2 topics
- Lift-O-Matic
- Hydraulic power lift (HPL) control valve oil flow
35 204 Remote control valves15 topics
- Rear remote valve arrangement
- Rear remote valve stacking
- Rear remote valve control levers
- Deluxe Quick-fit couplers
- Zero-pressure return port
- Mid-mount control valves (optional)
- Switching between single and double acting cylinders
- Single or double acting valve with automatic detent release and float
- Double-acting valve less automatic detent release and float
- Single-acting valve less automatic release and float
- TN60A, TN70A, and TN75A Series Hydraulic System Diagram
- Torque Settings
- Hydraulic Lift Tools
- Cross-sectional Views
- Hydraulic Lift Troubleshooting
35 110 40 Mechanically Controlled Lift Internal Controls Disassembly-Assembly1 topic
- Mechanically Controlled Lift Adjustments
35 110 08 Mechanically Controlled Lift Rod Mechanism Adjustments3 topics
- Lift Arm Descent Speed Adjustments
- Upper Stroke Limit Adjustment
- Adjusting the Upper Stroke Limit of the Lift-O-matic Device
35 260 Low-pressure, steering and lubrication system -- General Description5 topics
- Low-pressure oil flow
- Transmission lubrication system
- Steering system oil flow
- Electro-hydraulic four-wheel drive (FWD) for models with 40 kph transmissions
- System test fitting locations
41 000 Main data -- torque settings -- tools2 topics
- Components
- Troubleshooting
41 216 18 Steering control cylinder, Disassembly -- Assembly2 topics
- Main Data
- Description and Operation
41 206 20 Hydrostatic Steering Oil Pump -- Disassembly--Assembly (with unit removed)2 topics
- Torque Settings
- Tools
Analog Instruments2 topics
- Indicator Light Panel
- Transmitters, Sensors and Switches
55 000 Specifications5 topics
- Tightening Torques
- Troubleshooting
- Test and Check
- Overhaul
- Battery Maintenance
55 100 Electrical Circuit Connectors/Component Connectors Identification4 topics
- Wire Color Coding
- Connector Location Points
- Connectors / Component Connectors / Pin Locations
- Overhaul
55 000 How To Use Wiring Diagrams13 topics
- 2WD / Power-Shuttle Transmission Configuration / 3-Cylinder
- Mechanical 4WD / Power-Shuttle Transmission Configuration / 3-Cylinder
- 3-Cylinder
- 2WD / Mechanical Shuttle Transmission Configuration / 3-Cylinder
- Mechanical 4WD / Mechanical Shuttle Transmission Configuration / 3-Cylinder
- Configuration/ 3-Cylinder
- 2WD / Power-Shuttle Transmission Configuration / 4-Cylinder
- Mechanical 4WD / Power-Shuttle Transmission Configuration / 4-Cylinder
- 4-Cylinder
- 2WD / Mechanical Shuttle Transmission Configuration / 4-Cylinder
- Mechanical 4WD / Mechanical Shuttle Transmission Configuration / 4-Cylinder
- Configuration / 4-Cylinder
- Symbols Used in Electrical Diagrams
Inside this manual
Real pages from this service manual (1,191 pages). Open the sample pages (PDF, 800 KB)
- Troubleshooting, page 716: FAULT CODE 78
- Specifications, page 1,040: SECTION 55 -- ELECTRICAL SYSTEM -- CHAPTER 4
- Diagram, page 1,148: SECTION 55 -- ELECTRICAL SYSTEM -- CHAPTER 7
- Color page: SECTION 21 -- TRANSMISSIONS -- CHAPTER 1
- Color page: SECTION 10 -- ENGINE -- CHAPTER 3
- Foldout diagram: SECTION 55 -- ELECTRICAL SYSTEM -- CHAPTER 7
Other manuals for this machine
Save 10% on 2 manuals, 15% on 3 or more. Other manuals for the TN60A, TN70A, TN75A are listed below. Editions cover different serial number ranges: check the serial coverage and tick only the ones that match your machine.
Added to your cart. View cart
This is a service manual
Here's how it compares to the other manual types.
Service manual
Factory repair procedures and technical information such as specifications, troubleshooting, and wiring and hydraulic diagrams, for the models and systems the manual covers. See What's inside for its topics.
Operator's manual
Safe operation, controls, maintenance schedules, lubrication points, inspections, and basic checks. Repair procedures are in the service manual.
Parts manual
Illustrated diagrams with factory part numbers for identifying components and ordering parts. Repair procedures are in the service manual.
Engine service manuals are sometimes sold separately, since certain machine models were offered with more than one engine option.
What it's used for
Factory manual for in-house farm and construction shop use. Straightforward, complete, and easy to follow. It contains the OEM information dealership service departments and parts counters use to diagnose problems, identify components, and perform maintenance or repairs correctly.
Service shops and owner/operators who repair their own equipment
Identifying correct parts and seeing how assemblies come apart and go back together
Keeping equipment running with less downtime
Factory manual, 1,191 pages
Quantity one is the manual described above.
Fast free USA shipping
Ships in 1 business day.
60-day returns
Free if the mistake is ours. A manual ordered in error must come back unopened in its shrink-wrap; you pay return shipping and a 20% restocking fee applies. Return policy
Binder not included
Manuals over about 300 pages may need a standard 3-ring binder, which you can buy locally to keep the pages organized for shop use.
Questions about model, serial number, engine coverage or contents? Contact us before purchasing and we'll help confirm it's the right manual. Please verify the manual type, machine model, serial number range and engine coverage before purchasing: manuals ordered in error carry a 20% restocking fee (return policy).