Snorkel TB120 Telescopic Boom Lift Operator's Manual
107 pages · Publication 0192518
Added to your cart. View cart
- Models
- TB120
- Serial coverage
- Manufactured 7-05 and after
- Manual type
- Operator's Manual
- Pages
- 107
- Publication
- 0192518
- Condition
- Brand new
What's inside
From the manual's own table of contents: 171 topics. See sample pages (PDF, 577 KB)
- Aerial Platform Features
- Options
- Operator’s Manual
- Safety Alerts
- Operation
- Maintenance
- Used Material Disposal
- Manual of Responsibilities – ANSI
- MEWP Safe Use – AS/NZS
- AS/NZS 1418.10 Commissioning
- CE Compliance
- Additional Information
- Component Identification
- Working Envelope
- General Specifications
- Engine Oil Viscosity
- Electrocution Hazards
- Minimum Safe Approach Distance – ANSI
- Minimum Safe Approach Distance – AS/NZS
- Platform Capacity
- Manual Force
- Wind Speeds
- Prestart Inspection
- Work Place Inspection and Practices
Show all 171 topics
- Tip-Over and Falling Hazards
- Electrical System
- Hydraulic System
- Engine and Fuel Handling Precautions
- Placards and Decals
- General Safety Rules
- Emergency Stop Controls
- Emergency Power System
- Emergency Bleed Down System
- Emergency Lowering Knob
- Axle/Boom Interlock
- Ground Operation Switch
- Platform Foot Switch
- Guardrails
- Fall Protection Anchors
- Envelope Management System
- Height Restriction
- Ground Fault Circuit Interrupter
- Platform Overload Sensing System
- Tilt Alarm/Warning Light
- Engine Protection Systems
- High Engine Temperature Alarm
- Low Oil Pressure Alarm
- Horn
- Drive Motion Alarm
- Flashing Light
- Driving Lights
- Platform Work Lights
- Snorkel Guard
- Hour Meter
- Engine Temperature Gauge
- Ammeter
- Engine Air Filter Gauge
- Dual Fuel Engine Display
- Diagnostic Center/Engine Display
- EMS Display
- Platform Overload Warning Lights
- Tilt Warning Light
- Fuel Gauge
- Engine Oil
- Hydraulic Fluid Filter Gauge
- Fluid Level and Temperature Gauge
- Battery Disconnect Switch
- Axle Controls
- High Range Speed Selector – 4x4
- Lower Controls
- Start Switch
- Emergency Stop Button
- Controls Selector Switch
- Boom/Axle Switch
- Rotation Switch
- Boom Elevation Switch
- Boom Extension Switch
- Boom Speed Knob
- Platform Level Switch
- Platform Rotate Switch
- Engine/Emergency Power Switch
- Engine Speed Switch
- Fuel Switch
- Platform Overload Warning Light
- Diagnostic Center/Dual Fuel Engine Display
- Hydraulic Oil Warm-Up Switch
- Circuit Breaker Reset Buttons
- Upper Controls
- Boom Joystick
- Drive Joystick
- Drive Range Switch
- Boom Extend/Retract Joystick
- Throttle Switch
- Horn Button
- Override Switch
- Tilt Alarm
- Machine/Generator Switch
- Dual Fuel
- Driving and Platform Work Lights
- Operator’s Manual Holder
- Engine
- Oil Level
- Coolant
- Radiator
- Fuel Tank
- Fuel Line
- Air Filter
- Charging System
- Battery Fluid Level
- Battery Terminals
- Cables and Wiring Harness
- Fluid Level
- Fluid Filter
- Hoses, Tubes, and Fittings
- Tires and Wheels
- Lower Control Station
- Operating Controls
- Emergency Stop
- Emergency Power
- Emergency Lowering
- Level Sensor
- Structures
- Weldments
- Boom Slide Pads
- Wire Ropes
- Fasteners
- Upper Control Station
- Guardrail System
- Electrical Power Outlet
- Platform Control Cover
- Sandblast Protection Kit
- Air Line to Platform
- Tow Kit
- Platform Glazier Package
- Platform Welder
- Prestart Inspection Checklist
- Inspection and Maintenance Schedules
- Cold Weather Start-Up
- Engine Cold Weather Start Kit
- Cummins/Kubota – Block Heater
- Cummins – Ether Injection
- GM – Radiator Hose In-Line
- Hydraulic System Cold Weather Warm-Up
- Hydraulic System Warm-Up Switch
- Manually Warming The Hydraulic System
- Preparing for Operation
- Extending The Rear Axles
- Retracting The Rear Axles
- Boom Operation
- Driving and Steering
- Drive Speeds
- Four Wheel Drive
- High Range Speed Selector
- AC Generator
- Air Line
- Stowing
- Transporting
- Driving
- Winching
- Hoisting
- Securing for Transport
- Storage
- Electric Emergency Bleed Down System
- Manual Emergency Bleed Down System
- Towing
- Troubleshooting Chart
- Fuel Line Air Bleeding – Kubota V2403-T
- Open Bleeder Valve and Crank Engine
- Fill the Fuel Filter
- Operate Bleeder Pump
- Fuel Line Air Bleeding Kubota V2403-CR-TIE4B
Inside this manual
Real pages from this operator's manual (107 pages). Open the sample pages (PDF, 575 KB)
- Specifications, page 19: Chapter 2 – Specifications
- Controls and operation, page 39: Chapter 6 – Controls
- Maintenance, page 100: Appendix B – Inspection Checklists
- Color page, page 6: Warning
- Color page, page 23: Chapter 3 – Safety
Other manuals for this machine
Save 10% on 2 manuals, 15% on 3 or more. Other manuals for the TB120 are listed below. Editions cover different serial number ranges: check the serial coverage and tick only the ones that match your machine.
Added to your cart. View cart
This is an operator's manual
Here's how it compares to the other manual types.
Service manual
Factory repair procedures and technical information such as specifications, troubleshooting, and wiring and hydraulic diagrams, for the models and systems the manual covers. See What's inside for its topics.
Operator's manual
Safe operation, controls, maintenance schedules, lubrication points, inspections, and basic checks. Repair procedures are in the service manual.
Parts manual
Illustrated diagrams with factory part numbers for identifying components and ordering parts. Repair procedures are in the service manual.
What it's used for
Factory manual for in-house farm and construction shop use. Straightforward, complete, and easy to follow. It contains the OEM information dealership service departments and parts counters use to diagnose problems, identify components, and perform maintenance or repairs correctly.
Service shops and owner/operators who repair their own equipment
Identifying correct parts and seeing how assemblies come apart and go back together
Keeping equipment running with less downtime
Factory manual, 107 pages
Quantity one is the manual described above.
Fast free USA shipping
Ships in 1 business day.
60-day returns
Free if the mistake is ours. A manual ordered in error must come back unopened in its shrink-wrap; you pay return shipping and a 20% restocking fee applies. Return policy
Other editions and similar models
Questions about model, serial number, engine coverage or contents? Contact us before purchasing and we'll help confirm it's the right manual. Please verify the manual type, machine model, serial number range and engine coverage before purchasing: manuals ordered in error carry a 20% restocking fee (return policy).