Snorkel TB42, TB50 Telescopic Boom Lift Operator's Manual
87 pages · Publication 0074923
Added to your cart. View cart
What's inside
From the manual's own table of contents: 142 topics. See sample pages (PDF, 423 KB)
- Aerial Platform Features
- Options
- Operator’s Manual
- Safety Alerts
- Operation
- Maintenance
- Manual of Responsibilities
- Additional Information
- Component Identification
- Working Envelope – TB42
- Working Envelope – TB50
- General Specifications – TB42
- General Specifications – TB50
- Engine Specifications
- Engine Oil Viscosity
- Electrocution Hazards
- Minimum Safe Approach Distance
- Prestart Inspection
- Work Place Inspection and Practices
- Tip-Over and Falling Hazards
- Electrical System
- Hydraulic System
- Engine and Fuel Handling Precautions
- Placards and Decals
Show all 142 topics
- Emergency Stop Controls
- Emergency Power System
- Emergency Lowering Knob
- Ground Operation Switch
- Platform Foot Switch
- Guardrails
- Lanyard Anchors
- Ground Fault Circuit Interrupter
- Tilt Alarm
- Engine Protection Systems
- High Engine Temperature Alarm
- Low Oil Pressure Alarm
- Horn
- All Motion Alarm
- Flashing Light
- Driving Lights
- Platform Work Lights
- Hour Meter
- Engine Temperature Gauge
- Ammeter – Cummins/Deutz/Ford Engines
- Voltmeter – General Motors Engines
- Engine Air Filter Gauge
- Fuel Gauge
- Engine Oil
- Hydraulic Fluid Filter Gauge
- Fluid Level and Temperature Gauge
- Battery Disconnect Switch
- Lower Controls
- Emergency Stop Button
- Control Selector Switch
- Start Switch
- Rotation Switch
- Boom Elevation Switch
- Boom Extend/Retract Switch
- Boom Speed Knob
- Platform Level Switch
- Platform Rotation Switch
- Engine/Emergency Power Switch
- Throttle Switch
- Fuel Switch
- Hydraulic System Warm-up Switch
- Circuit Breaker Reset Buttons
- Upper Controls
- Drive Joystick
- Drive Range Switch
- Boom Joystick
- Boom Extension Switch
- Machine/Generator Switch
- Driving and Platform Work Lights
- Horn Button
- Engine
- Oil Level
- Coolant
- Radiator
- Fuel Tank
- Fuel Line
- Air Filter
- Charging System
- Cold Weather Start Kit
- Battery Fluid Level
- Battery Terminals
- Cables and Wiring Harness
- Fluid Level
- Fluid Filter
- Hoses, Tubes, and Fittings
- Tires and Wheels
- Lower Control Station
- Operating Controls
- Emergency Stop
- Emergency Power
- Emergency Lowering
- Level Sensor
- Sandblast Protection Kit
- Structures
- Weldments
- Slide Pads
- Wire Ropes
- Fasteners
- Upper Control Station
- Guardrail System
- Electrical Power Outlet
- Air Line to Platform
- Tow Kit
- Platform Glazier Package
- Platform Control Cover
- Prestart Inspection Checklist
- Cold Weather Start Up
- Engine Cold Weather Start Kit
- Cummins, Kubota and Ford – Block Heater
- Cummins – Ether Injection
- Deutz – Manifold Preheater
- GM – Radiator Hose In-Line
- Hydraulic System Cold Weather Warm-Up
- Manually Warming The Hydraulic System
- Preparing for Operation
- Boom Operation
- Driving and Steering
- Drive Speeds
- Motion Warning Alarm
- Four Wheel Drive
- Gradeability
- Percent vs. Degree of Slope
- Driving on a Slope
- Calculating Percent Grade
- Machine Gradeability
- AC Generator
- Dual Fuel
- Air Line
- Platform Capacity
- Stowing
- Transporting
- Driving
- Winching
- Hoisting
- Securing for Transport
- Towing
- Troubleshooting Chart
- Fuel Line Air Bleeding – Kubota V2403-M-T
Inside this manual
Real pages from this operator's manual (87 pages). Open the sample pages (PDF, 422 KB)
- Specifications, page 13: Chapter 2 – Specifications
- Controls and operation, page 28: The following are located on the lower control panel.
- Maintenance, page 38: Air Filter
- Color page, page 52: Chapter 7 – Prestart Inspection
Other manuals for this machine
Save 10% on 2 manuals, 15% on 3 or more. Other manuals for the TB42, TB50 are listed below. Editions cover different serial number ranges: check the serial coverage and tick only the ones that match your machine.
Added to your cart. View cart
This is an operator's manual
Here's how it compares to the other manual types.
Service manual
Factory repair procedures and technical information such as specifications, troubleshooting, and wiring and hydraulic diagrams, for the models and systems the manual covers. See What's inside for its topics.
Operator's manual
Safe operation, controls, maintenance schedules, lubrication points, inspections, and basic checks. Repair procedures are in the service manual.
Parts manual
Illustrated diagrams with factory part numbers for identifying components and ordering parts. Repair procedures are in the service manual.
What it's used for
Factory manual for in-house farm and construction shop use. Straightforward, complete, and easy to follow. It contains the OEM information dealership service departments and parts counters use to diagnose problems, identify components, and perform maintenance or repairs correctly.
Service shops and owner/operators who repair their own equipment
Identifying correct parts and seeing how assemblies come apart and go back together
Keeping equipment running with less downtime
Factory manual, 87 pages
Quantity one is the manual described above.
Fast free USA shipping
Ships in 1 business day.
60-day returns
Free if the mistake is ours. A manual ordered in error must come back unopened in its shrink-wrap; you pay return shipping and a 20% restocking fee applies. Return policy
Other editions and similar models
Questions about model, serial number, engine coverage or contents? Contact us before purchasing and we'll help confirm it's the right manual. Please verify the manual type, machine model, serial number range and engine coverage before purchasing: manuals ordered in error carry a 20% restocking fee (return policy).