Snorkel TB65J Telescopic Boom Lift Operator's Manual
75 pages · Publication 0084248
Added to your cart. View cart
- Models
- TB65J
- Serial coverage
- 000000 and after
- Manual type
- Operator's Manual
- Pages
- 75
- Publication
- 0084248
- Condition
- Brand new
What's inside
From the manual's own table of contents: 146 topics. See sample pages (PDF, 410 KB)
- Aerial Platform Features
- Options
- Operator’s Manual
- Safety Alerts
- Operation
- Maintenance
- Manual of Responsibilities
- Additional Information
- Component Identification
- General Specifications
- Engine Specifications
- Engine Oil Viscosity
- Electrocution Hazards
- Minimum Safe Approach Distance
- Prestart Inspection
- Work Place Inspection and Practices
- Tip-Over and Falling Hazards
- Electrical System
- Hydraulic System
- Engine and Fuel Handling Precautions
- Placards and Decals
- Emergency Stop Controls
- Emergency Power System
- Emergency Lowering Knob
Show all 146 topics
- Ground Operation Switch
- Platform Foot Switch
- Guardrails
- Lanyard Anchors
- Ground Fault Circuit Interrupter
- Tilt Alarm
- Engine Protection Systems
- High Engine Temperature Alarm
- Low Oil Pressure Alarm
- All Motion Alarm
- Horn
- Drive Motion Alarm
- Flashing Light
- Driving Lights
- Platform Work Lights
- Hour Meter
- Engine Temperature Gauge
- Ammeter
- Voltmeter – GM Engines
- Engine Air Filter Gauge
- Fuel Gauge
- Engine Oil
- Hydraulic Fluid Filter Gauge
- Fluid Level and Temperature Gauge
- Battery Disconnect Switch
- Lower Controls
- Start Switch
- Emergency Stop Button
- Controls Selector Switch
- Rotation Switch
- Boom Elevation Switch
- Boom Extension Switch
- Boom Speed Knob
- Jib Articulation Switch
- Platform Level Switch
- Platform Rotation Switch
- Engine/Emergency Power Switch
- Engine Speed Switch
- Manifold Air Inlet Heater – Deutz Only
- Fuel Switch
- Hydraulic Oil Warm-Up Switch
- Circuit Breaker Reset Buttons
- Upper Controls
- Boom Joystick
- Drive Joystick
- Drive Range Switch
- Throttle Switch
- Horn Button
- Machine/Generator Switch
- Driving and Platform Work Lights
- Operator’s Manual Holder
- Engine
- Oil Level
- Coolant
- Radiator
- Fuel Tank
- Fuel Line
- Air Filter
- Charging System
- Cold Weather Start Kit
- Battery Fluid Level
- Battery Terminals
- Cables and Wiring Harness
- Fluid Level
- Fluid Filter
- Hoses, Tubes, and Fittings
- Tires and Wheels
- Lower Control Station
- Operating Controls
- Emergency Stop
- Emergency Power
- Emergency Lowering
- Level Sensor
- Structures
- Weldments
- Boom Slide Pads
- Extension Cylinder Slide Pads
- Wire Ropes
- Fasteners
- Upper Control Station
- Guardrail System
- Electrical Power Outlet
- Platform Control Cover
- Sandblast Protection Kit
- Driving and Work Lights
- Platform Glazier Package
- Prestart Inspection Checklist
- Cold Weather Start-Up
- Engine Cold Weather Start Kit
- Cummins — Block Heater
- Deutz — Manifold Preheater
- GM — Radiator Hose In-Line
- Hydraulic System Cold Weather Warm-Up
- Hydraulic System Warm-Up Switch
- Manually Warming The Hydraulic System
- Preparing for Operation
- Boom Operation
- Driving and Steering
- Drive Speeds
- Gradeability
- Theoretical Gradeability
- Actual Gradeability
- Percent vs. Degree of Slope
- Driving on a Slope
- Calculating Percent Grade
- Machine Gradeability
- AC Generator
- Dual Fuel
- LP Fuel Tank
- Air Line
- Glazier Package
- Platform Capacity
- Platform Welder
- Stowing
- Tucked Stow
- Transporting
- Driving
- Winching
- Hoisting
- Securing for Transport
- Towing
- Troubleshooting Chart
Inside this manual
Real pages from this operator's manual (75 pages). Open the sample pages (PDF, 409 KB)
- Specifications, page 10: Chapter 2 – Specifications
- Maintenance, page 20: After the engine has been running for a few minutes under
- Controls and operation, page 26: Chapter 6 – Controls
- Color page, page 42: Chapter 7 – Prestart Inspection
Other manuals for this machine
Save 10% on 2 manuals, 15% on 3 or more. Other manuals for the TB65J are listed below. Editions cover different serial number ranges: check the serial coverage and tick only the ones that match your machine.
Added to your cart. View cart
This is an operator's manual
Here's how it compares to the other manual types.
Service manual
Factory repair procedures and technical information such as specifications, troubleshooting, and wiring and hydraulic diagrams, for the models and systems the manual covers. See What's inside for its topics.
Operator's manual
Safe operation, controls, maintenance schedules, lubrication points, inspections, and basic checks. Repair procedures are in the service manual.
Parts manual
Illustrated diagrams with factory part numbers for identifying components and ordering parts. Repair procedures are in the service manual.
What it's used for
Factory manual for in-house farm and construction shop use. Straightforward, complete, and easy to follow. It contains the OEM information dealership service departments and parts counters use to diagnose problems, identify components, and perform maintenance or repairs correctly.
Service shops and owner/operators who repair their own equipment
Identifying correct parts and seeing how assemblies come apart and go back together
Keeping equipment running with less downtime
Factory manual, 75 pages
Quantity one is the manual described above.
Fast free USA shipping
Ships in 1 business day.
60-day returns
Free if the mistake is ours. A manual ordered in error must come back unopened in its shrink-wrap; you pay return shipping and a 20% restocking fee applies. Return policy
Questions about model, serial number, engine coverage or contents? Contact us before purchasing and we'll help confirm it's the right manual. Please verify the manual type, machine model, serial number range and engine coverage before purchasing: manuals ordered in error carry a 20% restocking fee (return policy).