Case 340 Articulated Truck Service Manual
647 pages · Publication 9-93760
Added to your cart. View cart
- Models
- 340
- Manual type
- Service Manual
- Pages
- 647
- Publication
- 9-93760
- Condition
- Brand new
What's inside
From the manual's own table of contents: 10 sections, 393 entries. See sample pages (PDF, 649 KB)
CONDITIONS OF USE27 topics
- General diagram
- INTRODUCTION
- INFORMATION ON THIS HANDBOOK
- Definitions
- Symbols
- Purpose of this handbook
- To whom this manual is addressed
- Safekeeping of this handbook
- Updates to this handbook
- Units of measure
- SCHEDULED USE
- VEHICLE OPERATORS
- WASTE DISPOSAL
- SCRAPPING THE VEHICLE
- MANUFACTURER
- Warranty conditions
- Liability
- SERVICE
- Warranty coupons
- Spare parts
- GENERAL OPERATION RULES
- Pre--disassembly preparation
- During disassembly
- After disassembly
- During assembly
- Interchangeable parts
- Welding on the chassis
SAFETY INSTRUCTIONS19 topics
- Safety information and symbols
- General instructions
- PREVENTING FIRES
- ROLLOVER ACCIDENTS
- Prevention
- What to do if the vehicle rolls over
- INSTRUCTIONS FOR USE
- Starting and stopping
- Driving the vehicle
- Working the vehicle
- Towing the vehicle
- Replacing a wheel
- MAINTENANCE
- General
- Electrical power disconnection
- Safety locks
- Preventing injuries
- Preventing intoxication and contamination
- Preventing burns and electrocution
For the personnel and vehicle safety, read carefully the SAFETY INSTRUCTIONS contained in this handbook41 topics
- VEHICLE COMPOSITION
- DIMENSIONS
- DIMENSIONS WITH BODY RAISED
- WEIGHTS
- (HORIZONTAL POSITION)
- PERFORMANCE
- PERFORMANCE ALIGNMENT CHART
- MAIN TECHNICAL SPECIFICATIONS
- Chassis number
- ON MAIN GROUPS
- Chassis
- Engine
- Automatic transmission
- Drive axles
- Tipping cylinder
- Front suspension cylinder
- Front drive axle
- Intermediate and rear drive axles
- Suspension
- Brakes
- Wheels and tires
- Hydraulic system
- Brake cooling circuit
- Electrical system
- Drive cab
- Body
- LIST OF BULBS
- CAPACITIES
- TIRE PRESSURE TABLE
- COOLANT
- WINDSCREEN WASHER FLUID
- BATTERY ELECTROLYTE DENSITY TABLE
- TIGHTENING TORQUE
- PLATES APPLIED TO THE VEHICLE
- EUROPEAN VERSION
- INSIDE ENGINE HOOD PLATE
- U.S.A. VERSION
- INSIDE CAB PLATE
- STANDARD TIGHTENING TORQUES
- Screws and nuts with metric thread
- MEASURES (INTERNATIONAL SYSTEM)
ENGINE64 topics
- TECHNICAL SPECIFICATION
- WALK AROUND
- TRANSVERSAL SECTION
- LONGITUDINAL SECTION
- ELECTRONIC SYSTEM CONTROL
- Electrical and electronic components
- side
- Component location on engine left--hand side
- EDC ENGINE CONTROL UNIT LOCATION
- EDC CONTROL UNIT PIN -- OUT
- Connector “A” (Engine)
- Connector “B” (Cab/Chassis)
- GENERAL CHARACTERISTICS
- ASSEMBLY CLEARANCE DATA
- DIAGNOSTIC CONNECTOR PIN--OUT
- FAULT DISPLAY
- (blink--code)
- ENGINE FAILURE LIST
- ERROR CODES TABLE
- CURSOR TROUBLE SHOOTING GUIDE
- Foreword
- BLINK CODE
- TROUBLESHOOTING BY SYMPTOMS
- TIGHTENING TORQUES
- ENGINE BLOCK FASTENING SCREWS
- SCREWS TIGHTENING SEQUENCE
- FIXING SCREWS TIGHTENING SEQUENCE
- SEQUENCE
- FOR HEAT EXCHANGER SCREWS
- FOR ENGINE OIL SUMP SCREWS
- TOOLS
- ENGINE REMOVAL--REPLACEMENT
- Removal
- Replacement
- Checks and tests
- EXCHANGER REMOVAL--REPLACEMENT
- SPECIALIST MAINTENANCE
- Engine oil change
- Engine oil filter change
- Accessory drive belts
- Fuel circuit bleeding
- Fuel filter change
- cleaning
- DISMANTLING THE ENGINE ON THE BENCH
- REPAIR OPERATIONS
- CYLINDER BLOCK
- Checks and measurements
- CYLINDER LINERS
- Replacing cylinder liners
- Fitting and checking protrusion
- CRANKSHAFT
- Measuring main journals and crank pins
- half--shells
- FOR SELECTION
- pump
- Checking main journal installation clearance
- Checking crankshaft end float
- Piston--connecting rod assembly
- Measuring the diameter of the pistons
- coupling
- Piston rings
- CONNECTING ROD
- Checking con--rods
- Fitting piston rings
AUTOMATIC TRANSMISSION35 topics
- DESCRIPTION
- SECTION VIEW
- PIPE ARRANGEMENT VIEW
- TRANSMISSION SPEED SENSORS
- Speed sensor location
- Speed sensor setting
- FUNDAMENTAL COMPONENTS
- Torque converter
- Lock--up clutch
- Clutches
- Hydrodynamic brake (retarder)
- Central differential lock
- OPERATION
- FRONT DIFFERENTIAL FITTING
- TRANSMISSION OIL COOLING SYSTEM
- Test point delivery oil to filters unit location
- diagram
- COMPONENTS
- Connector key
- Transmission control unit pin--out
- DIAGNOSTIC
- TRANSMISSION FAILURE LIST
- TECHNICAL DATA
- AEB PROCEDURE
- Display – meaning of AEB procedure messages
- Central splitter
- Axle splitter
- Front axle
- Propeller shafts
- Driveline
- Checking oil level
- Changing the oil
- CENTRAL BEARING OVERHAUL
- Dismantling
- Assembly
FRONT AXLE10 topics
- First reduction: bevel pair
- Second reduction: hub and epicyclic train
- SPECIFICATIONS AND DATA
- Bevel gear (first reduction)
- Epicyclic train and hub (second reduction)
- FRONT HUB REMOVAL--REFIT
- Refit
- SPECIAL MAINTENANCE
- FRONT DIFFERENTIAL
- FRONT HUBS
INTERMEDIATE AXLE6 topics
- Splitter Unit
- First reduction: bevel gear pair
- Splitter unit and bevel gear pair (first reduction)
- Hub and epicyclic gear (second reduction)
- INTERMEDIATE AXLE REMOVAL--REFIT
- Pipes and supports removal
REAR AXLE23 topics
- Bevel gear pair (first reduction)
- Hub and epicyclic train (second reduction)
- REAR AXLE REMOVAL--REFIT
- Service braking circuit -- schematic diagram
- Service and parking brakes -- location
- Braking assembly
- Parking brake assembly
- WHEELS
- Front suspension
- Hydro--pneumatic cylinder -- description
- Hydro--pneumatic cylinder -- section
- Hydro--pneumatic cylinder -- view
- Rear suspension
- REMOVAL--REPLACEMENT
- Transfer shaft removal
- Piping and hub removal
- Front suspension element inflating device
- Equipment connection diagram
- Checking suspension element height
- Checking suspension element pressure
- Inflating the suspension elements
- Deflating the suspension element pressure
- Changing the suspension fluid element
HYDRAULIC SYSTEM33 topics
- Main components location
- TIPPING AND STEERING SYSTEM
- Main components
- Function
- EMERGENCY STEERING SYSTEM
- BRAKING SYSTEM
- BRAKES COOLING SYSTEM
- SYSTEM
- Interface flange
- Main pump
- Brake pump
- Emergency steering pump
- Tipping distributor
- Steering valve
- Counter--pressure valve
- Accumulators
- Fan drive
- Cartridge filters
- CONTROL PROCEDURES
- Checking parking brake efficiency
- valve
- efficiency
- PRESSURE TESTING PROCEDURE
- Hydraulic system pressure test point
- Hydraulic system pressure test point location
- Main pump (KAWASAKI)
- Tipping valve (EATON)
- Multifunctionnal display
- Main menu
- Vehicle management
- Calibrate body angle
- BRAKE PUMP REMOVAL--REPLACEMENT
- TIPPING VALVE REMOVAL--REPLACEMENT
PNEUMATIC SYSTEM125 topics
- PNEUMATIC DIAGRAM
- Compressor
- DRIER
- Parking brake distributor
- Checks
- MAIN COMPONENTS PNEUMATIC SYSTEM
- SINGLE--CHAMBER AIR DRIER
- AIR INTAKE VALVE
- PRESSURE RELIEF VALVE
- PARKING BRAKE ENGAGING DISTRIBUTOR
- PIPES AND COUPLINGS
- End forming on rigid pipes
- Bending rigid pipes
- Cutting rigid pipes
- couplings
- connection couplings
- ELECTRICAL SUPPLY
- Batteries
- GROUND POINTS
- TROL UNIT
- RELAYS AND FUSES
- Relays
- Supplementary relays
- Relays, resistors and diodes supplementary
- Fuse overview
- Supplementary fuses
- Fusebox component wiring
- BULKHEAD CONNECTORS
- Bulkhead location
- connector PIN OUT side
- through bulkhead connector PIN OUT side
- MULTIPLEX SYSTEM OVERVIEW
- Conventional control
- MULTIPLEX system
- CAN LINE
- Static efficiency tests
- Measurement values
- MULTIPLEX SYSTEM GENERAL DIAGRAM
- CAN OPEN LINE
- CAN OPEN line block diagram
- TOPOGRAPHIC DIAGRAM
- CAN OPEN LINE CIRCUIT DIAGRAM
- BODY COMPUTER SYSTEM COMPONENTS
- HEAD (body computer)
- HEAD and closing resistor location
- HEAD control unit PIN OUT
- MIDAC
- MIDAC LOCATION
- MIDAC 1 control unit PIN OUT
- MIDAC 2 control unit PIN OUT
- MIDAC 3 control unit PIN OUT
- CLUSTER
- CLUSTER location
- CLUSTER control unit PIN OUT
- CAN J1939 LINE
- CAN J1939 LINE CIRCUIT DIAGRAM
- LIST OF MULTIPLEX SYSTEM FAULTS
- Layout electrical system
- Hood/cab switch 209
- (manual pump)
- (electric pump)
- Component layout
- CAB REMOVAL--REPLACEMENT
- HOOD
- LOWER COVERS
- SIDE COVERS
- SIDE PANELS
- HOOD TILTING CYLINDER
- CAB TILTING CYLINDER
- Front chassis
- Rear chassis
- Articulation
- Articulation joint
- Articulation ball joint pre--load adjustment
- TESTS AND CHECKS
- Chassis lateral bending check
- Finding chassis bending up and down
- Finding chassis twist
- Precautions
- Straightening the chassis
- (FRONT CHASSIS)
- Side views
- Front distributor
- (REAR CHASSIS)
- Rear distributor
- MANUAL GREASING SYSTEM
- AIR--CONDITIONING SYSTEM
- Functional principle
- Functional outline
- Climate control system
- Climate control system air vents
- ELECTRICAL CIRCUIT DIAGRAM
- Colour code
- EQUIPMENT
- DIAGNOSTICS
- Fan not working
- Fan works but with poor air--flow
- Normal function but poor air cooling
- functioning poorly
- Diagnosis by pressure measurement
- Low pressure circuit -- insufficient pressure
- Low pressure circuit -- excessive pressure
- High pressure circuit -- insufficient pressure
- High pressure circuit -- excessive pressure
- System charge check
- Cleaning/replacing passenger air cleaner
- Cleaning condenser
- GENERAL SERVICING
- Usable fluids
- Draining R134a fluid
- Works on system piping
- Compressor lubricant
- PROCEDURES
- AND RECOVERY STATION OEM--1418
- CONTROL PANEL
- CHARGE CYLINDER AND OIL TANK
- SAFETY STANDARDS
- OPERATIONS FLOW DIAGRAM
- ON VEHICLE
- CREATING VACUUM IN SYSTEM
- RESTORING SYSTEM OIL
- WITH REFRIGERANT
- CHECKING SYSTEM PRESSURES
- STATION FROM SYSTEM
- WITH HFC R134A
Inside this manual
Real pages from this service manual (647 pages). Open the sample pages (PDF, 648 KB)
- Specifications, page 58: TECHNICAL DATA
- Troubleshooting, page 128: SECTION 3.1
- Diagram, page 518: ELECTRICAL SYSTEM
- Color page, page 461: HYDRAULIC SYSTEM
- Color page, page 499: Defective exhaust valve, valve seat or O---ring
- Foldout diagram, page 568: ELECTRICAL SYSTEM
Other manuals for this machine
Save 10% on 2 manuals, 15% on 3 or more. Other manuals for the 340 are listed below. Editions cover different serial number ranges: check the serial coverage and tick only the ones that match your machine.
Added to your cart. View cart
This is a service manual
Here's how it compares to the other manual types.
Service manual
Factory repair procedures and technical information such as specifications, troubleshooting, and wiring and hydraulic diagrams, for the models and systems the manual covers. See What's inside for its topics.
Operator's manual
Safe operation, controls, maintenance schedules, lubrication points, inspections, and basic checks. Repair procedures are in the service manual.
Parts manual
Illustrated diagrams with factory part numbers for identifying components and ordering parts. Repair procedures are in the service manual.
Engine service manuals are sometimes sold separately, since certain machine models were offered with more than one engine option.
What it's used for
Factory manual for in-house farm and construction shop use. Straightforward, complete, and easy to follow. It contains the OEM information dealership service departments and parts counters use to diagnose problems, identify components, and perform maintenance or repairs correctly.
Service shops and owner/operators who repair their own equipment
Identifying correct parts and seeing how assemblies come apart and go back together
Keeping equipment running with less downtime
Factory manual, 647 pages
Quantity one is the manual described above.
Fast free USA shipping
Ships in 1 business day.
60-day returns
Free if the mistake is ours. A manual ordered in error must come back unopened in its shrink-wrap; you pay return shipping and a 20% restocking fee applies. Return policy
Binder not included
Manuals over about 300 pages may need a standard 3-ring binder, which you can buy locally to keep the pages organized for shop use.
Other editions and similar models
Questions about model, serial number, engine coverage or contents? Contact us before purchasing and we'll help confirm it's the right manual. Please verify the manual type, machine model, serial number range and engine coverage before purchasing: manuals ordered in error carry a 20% restocking fee (return policy).