Snorkel 400S, 460SJ Telescopic Boom Lift Service and Maintenance Manual
321 pages · Publication 1435330-000
Added to your cart. View cart
What's inside
From the manual's own table of contents: 34 sections, 184 entries. See sample pages (PDF, 975 KB)
General34 topics
- Component Identification
- Chassis Component Location
- Serial Number Locations
- Working Envelope
- Abbreviations List
- Operator’s Manual Procedures
- General Specifications
- Engine Specifications
- Hydrostatic Pump Specifications
- Variable Displacement Hydraulic Pump Specifications
- Drive Motor Specifications
- Swing Drive Specifications
- Pressure Filter Specifications
- Gear Hub Box Specifications
- Brake Specifications
- Fastener Torque Chart
- Standard System
- Metric System
- Chassis Hydraulic Component Location
- Front Axle Assembly
- Traction Manifold
- Deutz Engine
- Hydrostatic Drive Pump
- Right View
- Left View
- Section Function Pump
- Drive Motor
- Gear Hub
- Chassis Hydraulic Hoses
- Oscillating Axle Cylinder
- Steer Cylinder
- Turntable Hydraulics
- Kubota Engine
- Hydraulic and Fuel Tank Tray
Hydraulic Pump1 topic
- Deutz Engine
Function Manifold1 topic
- Kubota Engine
Turntable Electrical4 topics
- Left Side
- Right Side
- Angle Limit Switch with Rocker Limit Switch
- Dual Capacity Sensors
Lower Control Box12 topics
- Rear Panel Components
- 400S - Single Capacity
- Front View
- Bottom View
- Internal Wiring
- 400S - Dual Capacity T4F
- 460SJ - Single Capacity T4F
- 460SJ - Dual Capacity T4F
- Valve Current Control Module
- Display
- GP400 Controller
- Terminal Board Module
Upper Control Box30 topics
- Outside View
- Inside View
- Wire Chart
- GP440 Controller
- Foot Switch
- Joystick
- Harnesses
- Hydrostatic Pump Harness
- Harnesses and Routing
- Engine Harness
- Hydraulic Manifold Harness
- Glo-Plug Relay Harness
- Function Manifold Harness
- Upper Control Box to Lower Control Box Harness
- Boom Elevation Limit Switch Harness
- Boom Angle Sensor
- Angle Sensor Harness
- Proximity Switch / Angle Sensor Harness
- Selector Valve Harness
- Upper Controls Internal Harness
- Deutz 2.9 L Engine
- Right View
- Left View
- V1505 Kubota Engine
- Right View
- Left View
- Throttle Solenoid
- Kubota Engine
- Bell Housing
- Front Axle
Main Boom3 topics
- Right Side View from Platform
- Boom Lift and Master Level Cylinders
- Left Side View from Platform
2KW Belt Driven Generator4 topics
- Specifications
- Installation
- Harness
- Troubleshooting
Show all 35 sections
Generator4 topics
- Hydraulic Components
- Electrical Panel
- Electrical Components
- Generator Switch at Upper Control Box
10KW Generator2 topics
- Power to Platform
- Generator to Inverter Installation
Cold Weather Package2 topics
- Kubota Engine and Turntable
- Kubota Engine and Platform
Platform AC Power1 topic
- ANSI
Bumpguard40 topics
- Platform Installation
- Upper Control Box
- Wiring
- LED Light Wire Harness
- Platform Lights
- Installation
- Harness
- Safety Precautions
- Recommended Tools
- Torque Hubs
- Throttle Adjustment
- Kubota Engine
- Check and Adjust Speed Sensor
- Kubota Engine
- Neutral Adjustment Screw
- Module Navigation
- Fault and Flash Codes
- Engine Codes
- Deutz Engine
- Oscillating Axle Lock Cylinder Operation
- Boom Elevation and Limit Switch Adjustment
- Boom Pressure Settings
- Hydraulic Pressure Adjustments for Function Manifold
- Booms Disassembly / Extend Cylinder Removal
- Cylinder Removal
- Main Boom
- Jib Boom
- Rotator
- Bleeding Procedure
- Assembly and Disassembly Procedure
- Troubleshooting Guide
- Overload Calibration
- General Maintenance
- Lubrication Points
- Battery Care and Maintenance
- Maintenance Schedule
- Prestart Inspection Checklist
- Frequent Inspection and Maintenance – Every 90 Days or 150 Hours
- Frequent Maintenance – Every 90 Days or 150 Hours
- Annual Maintenance – Every 500 Hours
Hydraulic Schematic6 topics
- Turntable with Tow Package and Hydraulic Warm-up Valve - Sheet 1
- Turntable with Oil Cooler - Sheet 1
- Sheet 1
- Tow Package and Cold Weather Package - Sheet 2
- Sheet 2
- Function Manifold
Electrical Schematic6 topics
- Deutz Engine Harness
- Kubota Engine Harness
- Board Pin Outs
- 12V TBM
- VCCM
- Lower Control Box
Inside this manual
Real pages from this service and maintenance manual (321 pages). Open the sample pages (PDF, 973 KB)
- Specifications, page 83: LOWER CONTROL BOX
- Troubleshooting, page 183: Section 9 Options
- Diagram, page 299: Section 12 Schematics
- Color page, page 90: October 2023
- Color page, page 139: October 2023
- Foldout diagram (color), page 319
Other manuals for this machine
Save 10% on 2 manuals, 15% on 3 or more. Other manuals are listed below. Editions cover different serial number ranges: check the serial coverage and tick only the ones that match your machine.
Added to your cart. View cart
This is a service manual
Here's how it compares to the other manual types.
Service manual
Factory repair procedures and technical information such as specifications, troubleshooting, and wiring and hydraulic diagrams, for the models and systems the manual covers. See What's inside for its topics.
Operator's manual
Safe operation, controls, maintenance schedules, lubrication points, inspections, and basic checks. Repair procedures are in the service manual.
Parts manual
Illustrated diagrams with factory part numbers for identifying components and ordering parts. Repair procedures are in the service manual.
Engine service manuals are sometimes sold separately, since certain machine models were offered with more than one engine option.
What it's used for
Factory manual for in-house farm and construction shop use. Straightforward, complete, and easy to follow. It contains the OEM information dealership service departments and parts counters use to diagnose problems, identify components, and perform maintenance or repairs correctly.
Service shops and owner/operators who repair their own equipment
Identifying correct parts and seeing how assemblies come apart and go back together
Keeping equipment running with less downtime
Factory manual, 321 pages
Quantity one is the manual described above.
Fast free USA shipping
Ships in 1 business day.
60-day returns
Free if the mistake is ours. A manual ordered in error must come back unopened in its shrink-wrap; you pay return shipping and a 20% restocking fee applies. Return policy
Binder not included
Manuals over about 300 pages may need a standard 3-ring binder, which you can buy locally to keep the pages organized for shop use.
Questions about model, serial number, engine coverage or contents? Contact us before purchasing and we'll help confirm it's the right manual. Please verify the manual type, machine model, serial number range and engine coverage before purchasing: manuals ordered in error carry a 20% restocking fee (return policy).