Snorkel 400S Telescopic Boom Lift Operator's Manual
95 pages · Publication 1433682
Added to your cart. View cart
- Models
- 400S
- Serial coverage
- 000000 and after
- Manual type
- Operator's Manual
- Pages
- 95
- Publication
- 1433682
- Condition
- Brand new
What's inside
From the manual's own table of contents: 151 topics. See sample pages (PDF, 584 KB)
- Aerial Platform Features
- Options
- Operator’s Manual
- Safety Alerts
- Operation
- Maintenance
- Used Material Disposal
- Manual of Responsibilities – ANSI
- MEWP Safe Use – AS/NZS
- AS/NZS 1418.10 Commissioning
- CE Compliance
- Additional Information
- Component Identification
- Working Envelope
- General Specifications
- Engine Specifications
- Engine Oil Viscosity
- Chapter 3 – Safety
- Electrocution Hazards
- Minimum Safe Approach Distance – ANSI
- Minimum Safe Approach Distance – AS/NZS
- Platform Capacity
- Manual Force
- Wind Speeds
Show all 151 topics
- Prestart Inspection
- Work Place Inspection and Practices
- Tip-Over and Falling Hazards
- Electrical System
- Hydraulic System
- Engine and Fuel Handling Precautions
- Placards and Decals
- General Safety Rules
- Emergency Stop Controls
- Emergency Power System
- Capacity Machines Only
- Ground Operation Switch
- Platform Foot Switch
- Guardrails
- Fall Protection Anchors
- Ground Fault Circuit Interrupter
- Platform Overload Sensing System
- Boom/Drive Cut-out
- Tilt Alarm/Warning Lights
- Engine Protection Systems
- High Engine Temperature Alarm
- Low Oil Pressure Alarm
- Horn
- Drive Motion Alarm
- All Motion Alarm
- Flashing Lights
- Driving Lights
- Platform Work Lights
- Snorkel Guard
- Diagnostic Center Display
- Platform Overload/Tilt Warning Lights
- Dual Platform Capacity System
- Engine Warning Lights
- Fuel
- Fluid Level and Temperature Gauge
- Engine Oil
- Battery Disconnect Switch
- Lower Controls
- Start/Emergency Power/Ground Operation Switch
- Emergency Stop Button
- Controls Selector Switch
- Rotation Switch
- Boom Elevation Switch
- Boom Extension Switch
- Platform Level Switch
- Platform Rotation Switch
- Platform Overload Warning Light
- Tilt Alarm
- Hydraulic Oil Warm-Up Switch
- Circuit Breaker Reset Buttons
- Upper Controls
- Start Switch
- Drive Joystick
- Drive Range Switch
- Boom Joystick
- Boom Extension Joystick
- Platform Rotate Joystick
- Engine/Emergency Power Switch
- Horn Switch
- Engine Speed Switch
- Override Switch
- AC Generator Switch
- Driving and Platform Work Lights
- Operator’s Manual Holder
- Engine
- Oil Level
- Coolant
- Radiator
- Fuel Tank
- Fuel Line
- Battery Terminals
- Cables and Wiring Harness
- Fluid Level
- Fluid Filter
- Hoses, Tubes, and Fittings
- Tires and Wheels
- Lower Control Station
- Operating Controls
- Emergency Stop
- Emergency Power
- Structures
- Weldments
- Boom Slide Pads
- Fasteners
- Upper Control Station
- Guardrail System
- Electrical Power Outlet
- Level Sensor
- Panel Carrier
- Sandblast Protection Kit
- Air Line to Platform
- Tow Kit
- Platform Glazier Package
- Platform Welder
- Pipe Rack
- Prestart Inspection Checklist
- Inspection and Maintenance Schedules
- Cold Weather Start-Up
- Hydraulic System Cold Weather Warm-Up
- Hydraulic System Warm-Up Switch
- Manually Warming The Hydraulic System
- Preparing for Operation
- Boom Operation
- Driving and Steering
- Drive Speeds
- Pivoting Front Axle
- Machine in Stowed Position
- Machine Not in Stowed Position
- Gradeability
- Percent vs. Degree of Slope
- Driving on a Slope
- Calculating Percent Grade
- Machine Gradeability
- AC Generator
- Air Line
- Snorkel OnSite
- After Use Each Day
- Stowing
- Transporting
- Driving
- Winching
- Hoisting
- Securing for Transport
- Storage
- ty Machines Only
- Towing
- Troubleshooting Chart
Inside this manual
Real pages from this operator's manual (95 pages). Open the sample pages (PDF, 582 KB)
- Specifications, page 16: Chapter 2 – Specifications
- Controls and operation, page 30: • Start/emergency power/ground operation switch
- Maintenance, page 88: Appendix B – Inspection Checklists
- Color page, page 6: Warning
- Color page, page 19: Chapter 3 – Safety
Other manuals for this machine
Save 10% on 2 manuals, 15% on 3 or more. Other manuals for the 400S are listed below. Editions cover different serial number ranges: check the serial coverage and tick only the ones that match your machine.
Added to your cart. View cart
This is an operator's manual
Here's how it compares to the other manual types.
Service manual
Factory repair procedures and technical information such as specifications, troubleshooting, and wiring and hydraulic diagrams, for the models and systems the manual covers. See What's inside for its topics.
Operator's manual
Safe operation, controls, maintenance schedules, lubrication points, inspections, and basic checks. Repair procedures are in the service manual.
Parts manual
Illustrated diagrams with factory part numbers for identifying components and ordering parts. Repair procedures are in the service manual.
What it's used for
Factory manual for in-house farm and construction shop use. Straightforward, complete, and easy to follow. It contains the OEM information dealership service departments and parts counters use to diagnose problems, identify components, and perform maintenance or repairs correctly.
Service shops and owner/operators who repair their own equipment
Identifying correct parts and seeing how assemblies come apart and go back together
Keeping equipment running with less downtime
Factory manual, 95 pages
Quantity one is the manual described above.
Fast free USA shipping
Ships in 1 business day.
60-day returns
Free if the mistake is ours. A manual ordered in error must come back unopened in its shrink-wrap; you pay return shipping and a 20% restocking fee applies. Return policy
Questions about model, serial number, engine coverage or contents? Contact us before purchasing and we'll help confirm it's the right manual. Please verify the manual type, machine model, serial number range and engine coverage before purchasing: manuals ordered in error carry a 20% restocking fee (return policy).