Terex Genie S-40 XC, S-40 HF, S-40 TraX, S-45 XC, S-45 HF, S-45 TraX Telescopic Boom Lift Service Manual
157 pages · Publication 1286829GT · Genie S-40 XC, S-40 HF, S-40 TraX, S-45 XC, S-45 HF, S-45 TraX,
Added to your cart. View cart
- Models
- Genie S-40 XC, S-40 HF, S-40 TraX, S-45 XC, S-45 HF, S-45 TraX
- Serial coverage
- from S40XCH-104, from S45XCH-101
- Manual type
- Service Manual
- Pages
- 157
- Publication
- 1286829GT
- Condition
- Brand new
What's inside
From the manual's own table of contents: 55 sections, 114 entries. See sample pages (PDF, 554 KB)
Introduction Introduction4 topics
- Important Information
- Find a Manual for this Model
- Revision History
- Serial Number Legend
Section 1 Safety Rules1 topic
- General Safety Rules
Section 2 Specifications13 topics
- Machine Specifications
- Performance Specifications
- Hydraulic Oil Specifications
- Hydraulic Component Specifications
- Manifold Component Specifications
- Ford MSG-425 EFI Engine Specifications
- Deutz D2011 L03i Engine Specifications
- Deutz D 2.9 L4 Engine Specifications
- Perkins 404F-E22T Engine Specifications
- Machine Torque Specifications
- TRAX Torque Specifications
- Hydraulic Hose and Fitting Torque Specifications
- Torque Procedure
Machine Functions3 topics
- How to Adjust the Machine Maximum Speed Setting
- How to Adjust the Joystick Ramp Rate Setting
- How to Adjust the Joystick Threshold Setting
Platform Overload System4 topics
- How to Calibrate the Platform Overload System
- How to Calibrate the Platform Overload System - HF Models
- How to Perform a Zero Load Platform Overload Calibration
- How to Replace the Platform Overload Load Cell
Jib Boom Lift Cylinder20 topics
- Primary Boom Components
- Cable Track
- How to Remove the Cable Track
- How to Repair the Cable Track
- Boom
- Boom Lift Cylinder
- Boom Extension Cylinder
- Platform Leveling Master Cylinder
- Primary Boom Angle Sensor Calibration
- Boom Length Sensor
- Engines
- RPM adjustment - Deutz Models
- RPM adjustment - Perkins Models
- Flex Plate
- How to install the Pump and Bell Housing Assembly
- Ford MSG-425 Engine Fault Codes
- Engine Fault Codes - Deutz D 2.9 L4 and Perkins 404F-22 Models
- Hydraulic Pump
- Function Pump
- Drive Pump
Show all 55 sections
Valve Adjustments - Function Manifold3 topics
- How to Adjust the System Relief Valve
- How to Adjust the Boom Down Relief Valve
- How to Adjust the Boom Extend Relief Valve
Valve Adjustment - Oscillate Relief Valve1 topic
- How to Set Up the Oscillate Directional Valve
Valve Coils1 topic
- How to Test a Coil Diode
Turntable Rotation Assembly2 topics
- How to Adjust the Turntable Rotation Gear Backlash
- How to Calibrate the Turntable Tilt Sensor
Section 4 Fault Codes7 topics
- Introduction
- Control System Fault Codes
- How to Retrieve Control System Fault Codes
- Control System Fault Codes - Models with Revision H Software or Higher
- Engine Fault Codes
- Deutz D 2.9 L4 Engine Fault Codes
- Perkins 404F-E22T Engine Fault Codes
Inside this manual
Real pages from this service manual (157 pages). Open the sample pages (PDF, 553 KB)
- Specifications, page 13: Specifications
- Troubleshooting, page 95: Control System Fault Codes
- Diagram, page 151: Electrical Schematic - Perkins 404F-E22T Models
- Foldout diagram, page 144: Service and Repair Manual
Other manuals for this machine
Save 10% on 2 manuals, 15% on 3 or more. Other manuals for the Genie S-40 XC, S-45 XC are listed below. Editions cover different serial number ranges: check the serial coverage and tick only the ones that match your machine.
Added to your cart. View cart
This is a service manual
Here's how it compares to the other manual types.
Service manual
Factory repair procedures and technical information such as specifications, troubleshooting, and wiring and hydraulic diagrams, for the models and systems the manual covers. See What's inside for its topics.
Operator's manual
Safe operation, controls, maintenance schedules, lubrication points, inspections, and basic checks. Repair procedures are in the service manual.
Parts manual
Illustrated diagrams with factory part numbers for identifying components and ordering parts. Repair procedures are in the service manual.
Engine service manuals are sometimes sold separately, since certain machine models were offered with more than one engine option.
What it's used for
Factory manual for in-house farm and construction shop use. Straightforward, complete, and easy to follow. It contains the OEM information dealership service departments and parts counters use to diagnose problems, identify components, and perform maintenance or repairs correctly.
Service shops and owner/operators who repair their own equipment
Identifying correct parts and seeing how assemblies come apart and go back together
Keeping equipment running with less downtime
Factory manual, 157 pages
Quantity one is the manual described above.
Fast free USA shipping
Ships in 1 business day.
60-day returns
Free if the mistake is ours. A manual ordered in error must come back unopened in its shrink-wrap; you pay return shipping and a 20% restocking fee applies. Return policy
Other editions and similar models
Questions about model, serial number, engine coverage or contents? Contact us before purchasing and we'll help confirm it's the right manual. Please verify the manual type, machine model, serial number range and engine coverage before purchasing: manuals ordered in error carry a 20% restocking fee (return policy).