Terex Genie S-60 J Telescopic Boom Lift Parts Manual
315 pages · Publication 1285304
Added to your cart. View cart
- Models
- Genie S-60 J
- Serial coverage
- from SN S60JH-101
- Manual type
- Parts Manual
- Pages
- 315
- Publication
- 1285304
- Condition
- Brand new
What's inside
From the manual's own table of contents: 14 sections, 119 entries. See sample pages (PDF, 436 KB)
Decals10 topics
- Decals with Words, Controls Side
- Decals with Words, Chassis
- Decals with Words, Engine Side
- Decals with Words, Boom
- Decals with Words, Platform
- Decals with Symbols, Controls Side
- Decals with Symbols, Chassis
- Decals with Symbols, Engine Side
- Decals with Symbols, Boom
- Decals with Symbols, Platform
Drive Chassis Components5 topics
- Steer Axle Linkage, View 1
- Steer Axle Linkage, View 2
- Steer Axle - Wheels and Hubs
- Non-steer Axle
- Oscillate Valve
Turntable Components23 topics
- Hydraulic and Fuel Tank Components
- Turntable Center Components
- Turntable Engine Side Components
- Turntable Controls Side Components
- Ground Control Box
- Turntable Covers - Controls Side
- Turntable Covers - Engine Side
- Turntable Counterweight
- Wire Harness
- Harness, Turntable Control
- Harness, Turntable Manifold
- Harness, Turntable Engine
- Harness, Cable Boom Power
- Harness, Boom Angle Sensor W/Limit Switch
- Harness PCON ALC600
- Harness, Jib Select
- Harness, LS1 Primary Retract
- Harness, Grount Cntl Box
- Harness, LS, OP, Drive Enable
- Cable,Retract Limit Switch
- Harness Joystick ALC600
- Battery Cable, Positive. Red
- Battery Cable, Negative. BLK
Battery Cable, Negative. BLK, Deutz2 topics
- Battery Negative Crossover Cable
- Harness, Engine, Kubota D1803
Harness, Engine, Kubota D110510 topics
- Harness, Welder Power To Plat
- Harness, Power To Plat AC
- Cable, Drive Light/Flashing Beacon Options
- Harness, Prox, Manifold, Plat
- Harness, Prox Sensor, ACP
- Harness, Light, Work
- Harness, Control, PASS
- Assembly, Cable, 8/5, Welder
- Assembly, Pigtail, 12/3, 15A Receptacle
- Harness, Oil Cooler, Liftpower
Engine Components11 topics
- Deutz D2011L03i Engine, View 1
- Deutz D2011L03i Engine, View 2
- Kubota D1803 Engine, View 1
- Kubota D1803 Engine, View 2
- Kubota D1803 Engine, View 3
- Kubota D1803 Engine, View 4
- Engine Tray (Deutz D2011L03i & Kubota D1803)
- Kubota D1105 Engine, View 1
- Kubota D1105 Engine, View 2
- Kubota D1105 Engine, View 3
- Engine Tray (Kubota D1105)
Boom Components7 topics
- Cable Track
- Boom Linkage, View 1
- Boom Linkage, View 2
- Extension Cylinder
- Primary and Secondary Boom Wear pads
- Boom End Components, Load Cell
- Boom End Components
Platform Components4 topics
- Platform Confurgation
- Platform Installation
- Platform Control Box
- Joysticks
Manifolds and Pumps6 topics
- Traction Manifold
- Function Manifold
- Jib and Platform Rotate Manifold
- Generator Manifold
- Two-Speed/Brake Manifold
- Pumps
Hydraulic Hose Routing and Fittings4 topics
- Turntable Components
- Drive System
- Oscillate System
- Boom Components
Accessories23 topics
- Drive Lights and Beacon Packages
- Work Lights
- Platform Accessories
- Half Mesh Option
- Air Line and Power to Platform
- Aircraft Protection, Standard Entry
- Aircraft Protection, Swing Gate
- Panel Cradle Option
- Contact Alarm Option
- Welder Option, Chassis Components
- Welder Option, Platform Components
- 3K Hydraulic Generator Option
- 7K Lift Power Generator Option (AUS) - View 1
- 7K Lift Power Generator Option (AUS) - View 2
- Hostile Environment, Boom Wipers
- Hostile Environment, Turntable Components
- Hostile Environment, Cylinder Bellows
- Hostile Environment, Ground and Platform Box Covers
- Engine Air Pre-Cleaners
- Fall Arrest Bar
- Cold Start Package
- Telematics Option
- PAS Option
Inside this manual
Real pages from this parts manual (315 pages). Open the sample pages (PDF, 435 KB)
- Parts illustration, page 115: 309.114A Battery Cable, Negative. BLK, Deutz
- Parts illustration, page 139: 309.124 Assembly, Cable, 8/5, Welder
- Parts illustration, page 271: 910.1 Welder Option, Chassis Components
Other manuals for this machine
Save 10% on 2 manuals, 15% on 3 or more. Other manuals for the Genie S-60 J are listed below. Editions cover different serial number ranges: check the serial coverage and tick only the ones that match your machine.
Added to your cart. View cart
This is a parts manual
Here's how it compares to the other manual types.
Service manual
Factory repair procedures and technical information such as specifications, troubleshooting, and wiring and hydraulic diagrams, for the models and systems the manual covers. See What's inside for its topics.
Operator's manual
Safe operation, controls, maintenance schedules, lubrication points, inspections, and basic checks. Repair procedures are in the service manual.
Parts manual
Illustrated diagrams with factory part numbers for identifying components and ordering parts. Repair procedures are in the service manual.
What it's used for
Factory manual for in-house farm and construction shop use. Straightforward, complete, and easy to follow. It contains the OEM information dealership service departments and parts counters use to diagnose problems, identify components, and perform maintenance or repairs correctly.
Service shops and owner/operators who repair their own equipment
Identifying correct parts and seeing how assemblies come apart and go back together
Keeping equipment running with less downtime
Factory manual, 315 pages
Quantity one is the manual described above.
Fast free USA shipping
Ships in 1 business day.
60-day returns
Free if the mistake is ours. A manual ordered in error must come back unopened in its shrink-wrap; you pay return shipping and a 20% restocking fee applies. Return policy
Binder not included
Manuals over about 300 pages may need a standard 3-ring binder, which you can buy locally to keep the pages organized for shop use.
Other editions and similar models
Questions about model, serial number, engine coverage or contents? Contact us before purchasing and we'll help confirm it's the right manual. Please verify the manual type, machine model, serial number range and engine coverage before purchasing: manuals ordered in error carry a 20% restocking fee (return policy).